journal article·2024-03

Effect of Rolling Temperature on Martensitic Transformation and Strain Hardening of Fe–21.2Mn–0.68C Steel

E. Dryzek, M. Wróbel, Ł. Rogal, M. Sarnek

Publisher page

Abstract

In this work, the temperature dependence of the stacking fault energy (SFE) of Fe–21.2Mn–0.68C steel was calculated using the thermodynamic model. The obtained dependence showed a decrease in the SFE with temperature and a saturation below the austenite Néel temperature. To demonstrate the effect of the SFE on the deformation-induced martensite transformations and strain hardening of Fe–21.2Mn–0.68C steel, the rolling was performed at different temperatures: close to the liquid nitrogen temperature, at room temperature, and at 473 K. The microstructure studies using electron backscatter diffraction, transmission electron microscopy, X-ray diffraction, and magnetization measurements revealed ε-martensite and a small amount of α′-martensite in samples rolled at two lower temperatures that correlated with their strain-hardening behavior. The calculated values of the SFE for these rolling temperatures were equal to 2 and 14 mJ/m2, respectively, confirming the plasticity mechanism’s dependence on the SFE.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (100+)

Show source-provided references
1. R.A. Hadfield: Science, 1888, vol. 12, pp. 284–86.
2. R.A. Hadfield: High manganese steel, (1883), British Patent, N°200/1883
3. ASTM Standard A128/A128M-93 (2012)
4. T.H. Raufoss: Raufoss Ammunisjonsfabrikker A/S, Norway, (1978) US Patent 4,130,418
5. G. Dinui, A. Najafizadeh, R. Uei, and S.M. Monir-Vaghefi: Mater. Des., 2010, vol. 31, pp. 3395–3402.10.1016/j.matdes.2010.01.049 ↗
6. H. Schumann: Neue Hütte, 1972, vol. 17, pp. 605–09.
7. L. Rémy and A. Pineau: Mat. Sci. Eng., 1977, vol. 28, pp. 99–107.10.1016/0025-5416(77)90093-3 ↗
8. T.W. Kim and Y.G. Kim: Mat. Sci. Eng. A, 1993, vol. 160, pp. 13–15.10.1016/0921-5093(93)90463-O ↗
9. O. Grässel, G. Frommeyer, C. Derder, and H. Hofman: J. Phys. IV France, 1997, vol. 07, pp. 383–88.10.1051/jp4:1997560 ↗
10. O. Grässel, L. Krüger, G. Frommeyer, and L.W. Meyer: Int. J. Plast., 2000, vol. 16, pp. 1391–1409.10.1016/S0749-6419(00)00015-2 ↗
11. G. Frommeyer, U. Brüx, and P. Neumann: ISIJ Int., 2003, vol. 43, pp. 438–46.10.2355/isijinternational.43.438 ↗
12. G. Frommeyer and O. Grädumay: Rev. Metall., 1998, vol. 95, pp. 1299–1310.10.1051/metal/199895101299 ↗
13. O. Bouaziz, H. Zurob, B. Chehab, J.D. Embury, S. Allain, and M. Huang: Mater. Sci. Technol., 2011, vol. 27, pp. 707–09.10.1179/026708309X12535382371852 ↗
14. D. Cornette, P. Cugy, A. Hildenbrand, M. Bouzekri, and G. Lovato: Metall. Res. Technol., 2005, vol. 107, pp. 905–18.
15. J.B. Nam, Development of New Auto Steels and Application Technology, China, 2013, Automotive Steel Conference, World Steel/CISA.
16. S. Allain, J.-P. Chateau, O. Bouaziz, S. Migot, and N. Guelton: Mater. Sci. Eng. A, 2004, vol. 387–389, pp. 158–62.10.1016/j.msea.2004.01.059 ↗
17. G. Dini, A. Najafizadeh, S.M. Monir-Vaghefi, and R. Ueji: Mater. Sci. Technol., 2010, vol. 26, pp. 181–86.10.1016/S1005-0302(10)60030-8 ↗
18. R.W. Cahn and P. Haasen, eds.: Physical metallurgy, North-Holland Publishing Co., Amsterdam, 1983.
19. G.B. Olson and M. Cohen: J. Less-comm Met., 1972, vol. 28, pp. 107–18.10.1016/0022-5088(72)90173-7 ↗
20. S. Lu, Q.-M. Hu, B. Johansson, and L. Vitos: Acta Mater., 2011, vol. 59, pp. 5728–34.10.1016/j.actamat.2011.05.049 ↗
21. A.R. Troiano and F.T. McGuire: Trans. ASM, 1943, vol. 31, pp. 340–64.
22. W. Schmidt: Arch. Eisenhüttenw., 1929/30, vol. 3, pp. 293–300.10.1002/srin.192901289 ↗
23. I. Gutierrez-Urrutia and D. Raabe: Scripta Mater., 2013, vol. 68, pp. 343–47.10.1016/j.scriptamat.2012.08.038 ↗
24. F. Lecroisey and A. Pineau: Metall. Mater. Trans. B, 1972, vol. 3, pp. 391–400.10.1007/BF02642042 ↗
25. G.B. Olson and M. Cohen: Metall. Mater. Trans. A, 1976, vol. 7A, pp. 1905–14.
26. J. Guimaraes and S.F. De Oliveira: Scripta Met., 1979, vol. 13, pp. 537–42.10.1016/0036-9748(79)90103-0 ↗
27. H.-S. Yang and H.K.D.H. Bhadeshia: Scripta Mater., 2009, vol. 60, pp. 493–95.10.1016/j.scriptamat.2008.11.043 ↗
28. J. Dash and H.M. Otte: Acta Met., 1963, vol. 11, pp. 1169–78.10.1016/0001-6160(63)90044-0 ↗
29. J.F. Breedis and L. Kaufman: Metall. Mater. Trans. B, 1971, vol. 2, pp. 2359–71.10.1007/BF02814874 ↗
30. T. Narutani, G.B. Olson, and M. Cohen: J. Phys. Colloques, 1982, vol. 43, pp. 429–34.10.1051/jphyscol:1982465 ↗
31. T. Narutani: Mater. Trans. JIM, 1989, vol. 30, pp. 33–45.10.2320/matertrans1989.30.33 ↗
32. J.A. Lishtenfeld, M.C. Mataya, and C.J. Tyne: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 147–61.10.1007/s11661-006-0160-5 ↗
33. P.M. Kelly: Acta Metall., 1965, vol. 13, pp. 635–46.10.1016/0001-6160(65)90126-4 ↗
34. L.I. Lysak and B.J. Nikolin: Fiz. Met. Metalloved., 1964, vol. 17, pp. 708–13.
35. P. Sahu, A.S. Hamada, T. Sahu, J. Puustinen, T. Oittinen, and L.P. Karjalainen: Metal. Mater. Trans. A, 2012, vol. 43A, pp. 47–55.10.1007/s11661-011-0818-5 ↗
36. E.I. Galindo-Nava and P.E.J. Rivera-Díaz-del-Castillo: Acta Mater., 2017, vol. 128, pp. 120–34.10.1016/j.actamat.2017.02.004 ↗
37. C. Liu, S. Shen, P. Xie, and C. Wu: Mater Charact, 2022, vol. 191, p. 112095.10.1016/j.matchar.2022.112095 ↗
38. E. Dryzek, M. Sarnek, and M. Wróbel: Nukleonika, 2015, vol. 60, pp. 709–12.10.1515/nuka-2015-0126 ↗
39. L. Chen, Y. Zhao, and X. Qin: Acta Metall. Sin., 2013, vol. 26, pp. 1–15.10.1007/s40195-012-0501-x ↗
40. M. Iker, D. Gaude-Fugarolas, P.J. Jacques, and F. Delannay: Adv. Mat. Res., 2006, vol. 15–17, pp. 852–57.
41. O. Bouaziz: Scripta Mater., 2012, vol. 66, pp. 982–85.10.1016/j.scriptamat.2011.11.029 ↗
42. A. Uniwersał, M. Wróbel, K. Wierzbanowski, S. Wroński, and A. Baczmański: Mater. Charact., 2019, vol. 148, pp. 214–23.10.1016/j.matchar.2018.12.017 ↗
43. P.E. Werner, L. Eriksson, and M. Westdahl: J. Appl. Crystallogr., 1985, vol. 18, pp. 367–70.10.1107/S0021889885010512 ↗
44. A. Boultif and D. Louër: J. Appl. Crystallogr., 2004, vol. 37, pp. 724–31.10.1107/S0021889804014876 ↗
45. Y. Lü, B. Hutchinson, D.A. Molodov, and G. Gottstein: Acta Mater., 2010, vol. 58, pp. 3079–90.10.1016/j.actamat.2010.01.045 ↗
46. S. Lee and B. De Cooman: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 5018–24.10.1007/s11661-013-1860-2 ↗
47. G.H. Eichelman and F.C. Hull: Trans. Am. Soc. Metal., 1953, vol. 45, pp. 77–104.
48. H. Schumann: Archiv für das Eisenhüttenwesen, 1967, vol. 38, pp. 647–56.10.1002/srin.196704234 ↗
49. H. Schumann: Krist. Tech., 1974, vol. 9, pp. 1141–52.10.1002/crat.19740091009 ↗
50. F.B. Pickering: in Proc. Conf. Stainless Steels 84, Göteborg, 3-4 Sept. 1984, the Institute of Metals London, 1985, pp. 2–28.
51. H.-S. Yang, J.H. Jang, H.K.D.H. Bhadeshia, and D.W. Suh: Calphad, 2012, vol. 36, pp. 16–22.10.1016/j.calphad.2011.10.008 ↗
52. J.P. Hirth: Metall. Trans. B, 1970, vol. 1, pp. 2367–74.10.1007/BF03038365 ↗
53. T. Schneider, M. Acct, B. Rellinghaus, E.F. Wassermann, and W. Pepperhoff: Phys. Rev. B, 1995, vol. 51, pp. 8917–21.10.1103/PhysRevB.51.8917 ↗
54. T. Sasaki, K. Watanabe, K. Nohara, Y. Ono, N. Kondo, and S. Sato: ISIJ Int., 1982, vol. 22, pp. 1010–20.10.2355/isijinternational1966.22.1010 ↗
55. O. Zambrano: J. Eng. Mater. Technol., 2016, vol. 138, p. 041010.10.1115/1.4033632 ↗
56. A. Saeed-Akbari, J. Imlau, U. Prahl, and W. Bleck: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 3076–90.10.1007/s11661-009-0050-8 ↗
57. D.T. Pierce, J.A. Jiménez, J. Bentley, D. Raabe, C. Oskay, and J.E. Wittig: Acta Mater., 2014, vol. 68, pp. 238–53.10.1016/j.actamat.2014.01.001 ↗
58. K. Sato, M. Ichinose, Y. Hirotsu, and Y. Inoue: ISIJ Int., 1989, vol. 29, pp. 868–77.10.2355/isijinternational.29.868 ↗
59. A. Dumay, J.-P. Chateau, S. Allain, S. Migot, and O. Bouaziz: Mat. Sci. Eng. A, 2008, vol. 483–484, pp. 184–87.10.1016/j.msea.2006.12.170 ↗
60. A.T. Dinsdale: Calphad, 1991, vol. 15, pp. 317–425.10.1016/0364-5916(91)90030-N ↗
61. B. Wu, B. Qian, and Y. Wen: Mater. Sci. Technol., 2016, vol. 33, pp. 1019–25.10.1080/02670836.2016.1262318 ↗
62. L. Li and T.Y. Hsu: Calphad, 1997, vol. 21, pp. 443–48.10.1016/S0364-5916(97)00044-8 ↗
63. S. Allain, J.-P. Chateau, and O. Bouaziz: Mater. Sci. Eng. A, 2004, vol. 387–389, pp. 143–47.10.1016/j.msea.2004.01.060 ↗
64. J.-E. Jin, M. Jung, C.-Y. Lee, J. Jeong, and Y.-K. Lee: Met. Mater. Int., 2012, vol. 18, pp. 419–23.10.1007/s12540-012-3006-2 ↗
65. W. Huang: Calphad, 1989, vol. 13, pp. 243–52.10.1016/0364-5916(89)90004-7 ↗
66. A.P. Miodownik: Int. J. Mater. Res., 1998, vol. 89, pp. 840–46.
67. K. Ishida: Phys. Stat. Sol. (a), 1976, vol. 36, pp. 717–28.10.1002/pssa.2210360233 ↗
68. Y.-K. Lee and C. Choi: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 355–60.10.1007/s11661-000-0271-3 ↗
69. J.-Y. Lee, J.-S. Hong, S.-H. Kang, and Y.-K. Lee: Mater. Sci. Eng. A, 2021, vol. 809, p. 140972.10.1016/j.msea.2021.140972 ↗
70. Y.W. Choi, Z. Dong, W. Li, S. Schönecker, H. Kim, S. Kwon, and L. Vitos: Mater. Des., 2020, vol. 187, p. 108392.10.1016/j.matdes.2019.108392 ↗
71. J.S. Aristeidakis and G.N. Haidemenopoulos: Acta Mater., 2020, vol. 193, pp. 291–310.10.1016/j.actamat.2020.03.052 ↗
72. S.M. Cotes, A. Fernández Guillermet, and M. Sade: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 83–91.10.1007/s11661-004-0111-y ↗
73. P.U. Volosevich, V.N. Gridnev, and Yu.N. Petrov: Fiz. Met. Metalloved., 1976, vol. 42, pp. 372–76.
74. G. Frommeyer, U. Brux, and P. Neumann: ISIJ Int., 2003, vol. 43, pp. 438–46.10.2355/isijinternational.43.438 ↗
75. P. Chowdhury, D. Canadinc, and H. Sehitoglu: Mater. Sci. Eng. R, 2017, vol. 122, pp. 1–28.10.1016/j.mser.2017.09.002 ↗
76. L. Rémy: Thesis, Universite d'Orsay, Paris, 1975
77. B. Ma, Ch. Li, Y. Han, and J. Wang: J. Magn. Magn. Mater., 2016, vol. 419, pp. 249–54.10.1016/j.jmmm.2016.06.013 ↗
78. L. Zhao, N.H. van Dijk, A.J.E. Lefering, and J. Sietsma: J. Mater. Sci., 2013, vol. 48, pp. 1474–79.10.1007/s10853-012-6902-4 ↗
79. L. Bracke, G. Mertens, J. Penning, B.C. de Cooman, M. Liebeherr, and N. Akdut: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 307–17.10.1007/s11661-006-0002-5 ↗
80. J. Kowalska, W. Ratuszek, M. Witkowska, A. Zielińska-Lipiec, and T. Tokarski: J. Alloys Compd., 2015, vol. 643, pp. 39–45.10.1016/j.jallcom.2015.04.086 ↗
81. J. Kowalska and M. Kowalski: J. Mater. Eng. Perform., 2020, vol. 29, pp. 1495–1501.10.1007/s11665-019-04516-y ↗
82. R.T. Van Tol, J.K. Kim, L. Zhao, J. Sietsma, and B.C. De Cooman: J. Mater. Sci., 2012, vol. 47, pp. 4845–50.10.1007/s10853-012-6345-y ↗
83. J. Kowalska, J. Ryś, and G. Cempura: Materials (Basel), 2021, vol. 14, p. 6935.10.3390/ma14226935 ↗
84. J.E.C. Sabisch, J.D. Sugar, J. Ronevich, C. San Merchi, and D.L. Medlin: Metall. Mater. Trans. A, 2021, vol. 52A, pp. 1516–25.10.1007/s11661-021-06170-3 ↗
85. S.-J. Lee, J. Han, S. Lee, S.-H. Kang, S.-M. Lee, and Y.-K. Lee: Sci. Rep., 2017, vol. 7, p. 3573.10.1038/s41598-017-03862-y ↗
86. B.J. Duggan, M. Hatherly, W.B. Hutchinson, and P.T. Wakefield: Met. Sci., 1978, vol. 12, pp. 343–51.10.1179/030634578790433909 ↗
87. D. Sagapurama, K. Viswanathanb, K.P. Trumblec, and S. Chandrasekarc: Philos. Mag., 2018, vol. 98, pp. 3267–99.10.1080/14786435.2018.1524586 ↗
88. K. Viswanathan, S. Yadoav, and D. Sagapuram: Appl. Mech. Rev., 2020, vol. 72, p. 060802.10.1115/1.4049353 ↗
89. G.B. Olson and M. Cohen: Metall. Mater. Trans. A, 1975, vol. 6A, pp. 791–95.10.1007/BF02672301 ↗
90. D. Medlin, J. Sabisch, J. Sugar, Ch. San Merchi and J. Ronevich, Strain localization and martensitic transformations at shear bands in a low SFE austenitic stainless steel, https://www.osti.gov/servlets/purl/1783573. Accessed 29 May 202310.2172/2431705 ↗
91. M. Blicharski, S. Dymek, and M. Wróbel: J. Mater. Process. Technol., 1995, vol. 53, pp. 75–84.10.1016/0924-0136(95)01963-F ↗
92. M. Blicharski and S. Gorczyca: Met. Sci., 1978, vol. 12, pp. 302–12.10.1179/msc.1978.12.7.303 ↗
93. Y. Xiong, Y. Yue, T. He, Y. Lu, F. Ren, and W. Cao: Materials, 2018, vol. 11, p. 1557.10.3390/ma11091557 ↗
94. J.E.C. Sabisch, J.D. Sugar, J. Ronevich, C. San Marchi, and D.I. Medlin: Metall. Mater. Trans. A, 2021, vol. 52A, pp. 1516–25.10.1007/s11661-021-06170-3 ↗
95. J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, 2nd ed. Elsevier Ltd., Amsterdam, 2004.
96. M. Wróbel, S. Dymek, and M. Blicharski: Arch. Metall., 1993, vol. 39, pp. 195–203.
97. M. Hatherly and A.S. Malin: Scripta Metall., 1984, vol. 18, pp. 449–54.10.1016/0036-9748(84)90419-8 ↗
98. B.C. DeCooman, Y. Estrin, and S.K. Kim: Acta Mater., 2018, vol. 142, pp. 283–362.10.1016/j.actamat.2017.06.046 ↗
99. P.S. Branicio, J.Y. Zhang, and D.J. Srolovitz: Phys. Rev. B, 2013, vol. 88, p. 64104.10.1103/PhysRevB.88.064104 ↗
100. M. Wróbel, S. Dymek, M. Blicharski, and S. Gorczyca: Text. Microstruct., 1988, vol. 10, p. 364628.