Engineering Grain Boundary Constitution in Pulse Electrodeposited Nickel Coatings for Enhanced Resistance to Electrochemical Degradation
Source abstract
Abstract
Ni coatings were electrodeposited over mild steel using a pulsed electrodeposition technique at three different duty cycles (30, 60, and 80 pct) with three different frequencies (25, 75, and 150 Hz) corresponding to each duty cycle. The influence of particular duty cycle sets and frequency on the micro-texture and corrosion behavior of coatings was investigated. Potentiodynamic polarization tests revealed the lowest corrosion rate for deposits obtained at 80 pct duty cycle and frequency of 75 Hz. In comparison, the highest corrosion rate was measured for deposits obtained at 80 pct duty cycle and frequency of 150 Hz. A decrease of around 57 pct in corrosion current density between the lowest and the highest corrosion-resistant coatings was observed. Similar trends in corrosion behavior were observed using electrochemical impedance spectroscopy (EIS) results. Electron backscatter diffraction (EBSD) analysis revealed that the pulse deposition parameters did not affect the coating surface texture but significantly altered the grain boundary constitution and coating strain. The lower corrosion rate of coatings obtained at 80 pct duty cycle and 75 Hz frequency was due to a higher fraction of both coincident site lattice boundaries (CSLs) and low-angle grain boundaries (LAGBs) along with lower coating strain. The higher corrosion rate of coatings obtained at 80 pct duty cycle and 150 Hz frequency was due to a higher fraction of high-angle grain boundaries (HAGBs), a lower fraction of CSLs, and higher coating strain. © The Minerals, Metals & Materials Society and ASM International 2024.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Corrosion Behavior and Inhibition · Electrodeposition and Electroless Coatings · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (52)
Show source-provided references
1. N.S. Mbugua, M. Kang, Y. Zhang, N.J. Ndiithi, G.V. Bertrand, and L. Yao: Materials, 2020, vol. 13, p. 13.10.3390/ma13163475 ↗
2. R.A. Horch, T.D. Golden, N.A. D’souza, and L. Riester: Chem. Mater., 2002, vol. 14(8), pp. 3531–38. https://doi.org/10.1021/cm010812+.10.1021/cm010812+ ↗
3. E. Beltowska-Lehman, P. Indyka, A. Bigos, M.J. Szczerba, J. Guspiel, H. Koscielny, and M. Kot: Mater. Chem. Phys., 2016, vol. 173, pp. 524–33. https://doi.org/10.1016/j.matchemphys.2016.02.050.10.1016/j.matchemphys.2016.02.050 ↗
4. A. Laszczyńska, W. Tylus, J. Winiarski, and I. Szczygieł: Surf. Coat. Technol., 2017, vol. 317, pp. 26–37. https://doi.org/10.1016/j.surfcoat.2017.03.043.10.1016/j.surfcoat.2017.03.043 ↗
5. M.H. Allahyarzadeh, M. Aliofkhazraei, A.R. Rezvanian, V. Torabinejad, and A.R.S. Rouhaghdam: Surf. Coat. Technol., 2016, vol. 307A, pp. 978–1010. https://doi.org/10.1016/j.surfcoat.2016.09.052.10.1016/j.surfcoat.2016.09.052 ↗
6. F. Doğan, M. Uysal, E. Duru, H. Akbulut, and S. Aslan: J. Asian Ceram. Soc., 2020, vol. 8(4), pp. 1271–84. https://doi.org/10.1080/21870764.2020.1840704.10.1080/21870764.2020.1840704 ↗
7. F. Erdemir, O. Güler, and A. Çanakçı: J. Energy Storage, 2021, vol. 44A, 103364. https://doi.org/10.1016/j.est.2021.103364.10.1016/j.est.2021.103364 ↗
8. O. Güler, M. Kocaman, S.B. Akçay, H. Çuvalcı, and T. Varol: Surf. Coat. Technol., 2022, vol. 421, 129025. https://doi.org/10.1016/j.surfcoat.2022.129025.10.1016/j.surfcoat.2022.129025 ↗
9. O. Güler: Colloids Surf. A, 2023, vol. 673, 131858. https://doi.org/10.1016/j.colsurfa.2023.131858.10.1016/j.colsurfa.2023.131858 ↗
10. S.B. Akçay, M. Kocaman, M. Çelebi, O. Güler, and T. Varol: Surf. Coat. Technol., 2024, vol. 478, 130417. https://doi.org/10.1016/j.surfcoat.2024.130417.10.1016/j.surfcoat.2024.130417 ↗
11. K.S. Jyotheender and C. Srivastava: Materialia, 2022, vol. 22, 101431. https://doi.org/10.1016/j.mtla.2022.101431.10.1016/j.mtla.2022.101431 ↗
12. A. Aliyu, K.S. Jyotheender, and C. Srivastava: Surf. Coat. Technol., 2021, vol. 412, p. 127079. https://doi.org/10.1016/j.surfcoat.2021.127079.10.1016/j.surfcoat.2021.127079 ↗
13. A.P. Meshram, A. Gupta, and C. Srivastava: Materialia, 2022, vol. 22, 101413. https://doi.org/10.1016/j.mtla.2022.101413.10.1016/j.mtla.2022.101413 ↗
14. P. Biswas, S.K. Das, and P. Sahoo: Mater. Today Proc., 2023, vol. 80, pp. 1122–29.10.1016/j.matpr.2022.12.119 ↗
15. V.B. Chintada, T.R. Gurugubelli, and R. Koutavarapu: Mater. Chem. Phys., 2022, vol. 291, 126682. https://doi.org/10.1016/j.matchemphys.2022.126682.10.1016/j.matchemphys.2022.126682 ↗
16. W.E.G. Hansal, G. Sandulache, R. Mann, and P. Leisner: Electrochim. Acta, 2013, vol. 114, pp. 851–58.10.1016/j.electacta.2013.08.182 ↗
17. S. Ahmadiyeh, A. Rasooli, and M.G. Hosseini: Metall. Mater. Trans. A, 2020, vol. 51A, pp. 3167–79.10.1007/s11661-020-05718-z ↗
18. C. Prasad, K. Bhavani, R. Vemuri, V.V. Ramana, and K. Sriramvikas: Chem. Data Collect., 2022, vol. 41, 100927. https://doi.org/10.1016/j.cdc.2022.100927.10.1016/j.cdc.2022.100927 ↗
19. F. Nasirpouri, M.R. Sanaeian, A.S. Samardak, E.V. Sukovatitsina, A.V. Ognev, L.A. Chebotkevich, M.G. Hosseini, and M. Abdolmaleki: Appl. Surf. Sci., 2014, vol. 292, pp. 795–805.10.1016/j.apsusc.2013.12.053 ↗
20. M. Cherkaoui, E. Chassaing, and K.V. Quang: Surf. Coat. Technol., 1988, vol. 34(3), pp. 243–52. https://doi.org/10.1016/0257-8972(88)90116-8.10.1016/0257-8972(88)90116-8 ↗
21. H.L. Seet, X.P. Li, Z.J. Zhao, Y.K. Kong, H.M. Zheng, and W.C. Ng: J. Appl. Phys., 2005, vol. 97, p. 15. https://doi.org/10.1063/1.1855712.10.1063/1.1855712 ↗
22. T. Liu, H. Li, and Z. Xiao: Int. J. Electrochem. Sci., 2023, vol. 18, 100130. https://doi.org/10.1016/j.ijoes.2023.100130.10.1016/j.ijoes.2023.100130 ↗
23. M.S. Chandrasekar and M. Pushpavanam: Electrochim. Acta, 2008, vol. 53, pp. 3313–22. https://doi.org/10.1016/j.electacta.2007.11.054.10.1016/j.electacta.2007.11.054 ↗
24. R. Ramanauskas, L. Gudavičiute, O. Ščit, D. Bučinskiene, and R. Juskenas: Trans. Inst. Met. Finish., 2008, vol. 86, pp. 103–108.10.1179/174591908X272924 ↗
25. A. John, A. Saeed, and Z.A. Khan: Materials, 2023, vol. 16(6), p. 2192. https://doi.org/10.3390/ma16062192.10.3390/ma16062192 ↗
26. M.H. Sliem, K. Shahzad, V.N. Sivaprasad, R.A. Shakoor, A.M. Abdullah, O. Fayyaz, R. Kahraman, and M.A. Umer: Surf. Coat. Technol., 2020, vol. 403, 126340. https://doi.org/10.1016/j.surfcoat.2020.126340.10.1016/j.surfcoat.2020.126340 ↗
27. A. Boukhouiete and J. Creus: J. Mater. Environ. Sci., 2015, vol. 6(7), pp. 1840–44.
28. C. Kollia, N. Spyrellis, J. Amblard, M. Froment, and G. Maurin: J. Appl. Electrochem., 1990, vol. 20(6), pp. 1025–32. https://doi.org/10.1007/BF01019584.10.1007/BF01019584 ↗
29. N.S. Qu, D. Zhu, K.C. Chan, and W.N. Lei: Surf. Coat. Technol., 2003, vol. 168(2–3), pp. 123–28. https://doi.org/10.1016/S0257-8972(03)00014-8.10.1016/S0257-8972(03)00014-8 ↗
30. Y. Lu, S. Luo, Z. Ren, Y. Zou, S. Zhong, Y. Wu, C. Liu, and M. Yang: Surf. Coat. Technol., 2021, vol. 409, 126833. https://doi.org/10.1016/j.surfcoat.2021.126833.10.1016/j.surfcoat.2021.126833 ↗
31. S. Nigam, S.K. Patel, S.S. Mahapatra, N. Sharma, and K.S. Ghosh: in IOP Conference Series: Materials Science and Engineering, vol. 75, Institute of Physics Publishing, 2015.10.1088/1757-899X/75/1/012024 ↗
32. P. Kar, P.S. Prasad, M.M. Ghosh, and K.S. Ghosh: Philos. Mag. Lett., 2020, vol. 100, pp. 162–70.10.1080/09500839.2020.1736356 ↗
33. Y. Tsuru, M. Nomura, and F.R. Foulkes: J. Appl. Electrochem., 2002, vol. 32(6), pp. 629–34. https://doi.org/10.1023/A:1020130205866.10.1023/A:1020130205866 ↗
34. Y. Deo, R. Ghosh, A. Nag, D.V. Kumar, R. Mondal, and A. Banerjee: Electrochim. Acta, 2021, vol. 399, 139379. https://doi.org/10.1016/j.electacta.2021.139379.10.1016/j.electacta.2021.139379 ↗
35. R. Sharma, A. Yadav, S. Arora, and N. Kishore: Mater. Today Proc., 2020, vol. 44, pp. 4651–56. https://doi.org/10.1016/j.matpr.2020.10.927.10.1016/j.matpr.2020.10.927 ↗
36. Z. Zhang, C. Jiang, P. Fu, F. Cai, and N. Ma: J. Alloys Compd., 2015, vol. 626, pp. 118–23. https://doi.org/10.1016/j.jallcom.2014.11.144.10.1016/j.jallcom.2014.11.144 ↗
37. A. Aliyu and C. Srivastava: Materialia, 2019, vol. 5, 100249. https://doi.org/10.1016/j.mtla.2019.100249.10.1016/j.mtla.2019.100249 ↗
38. J.B. Jorcin, M.E. Orazem, N. Pébère, and B. Tribollet: Electrochim. Acta, 2006, vol. 51, pp. 1473–79. https://doi.org/10.1016/j.electacta.2005.02.128.10.1016/j.electacta.2005.02.128 ↗
39. B. Hirschorn, M.E. Orazem, B. Tribollet, V. Vivier, I. Frateur, and M. Musiani: Electrochim. Acta, 2010, vol. 55, pp. 6218–27. https://doi.org/10.1016/j.electacta.2009.10.065.10.1016/j.electacta.2009.10.065 ↗
40. L. Liu, Y. Li, C. Zeng, and F. Wang: Electrochim. Acta, 2006, vol. 51, pp. 4736–43. https://doi.org/10.1016/j.electacta.2006.01.033.10.1016/j.electacta.2006.01.033 ↗
41. M. Isakhani-Zakaria, S.R. Allahkaram, and H.A. Ramezani-Varzaneh: Corros. Sci., 2019, vol. 157, pp. 472–80. https://doi.org/10.1016/j.corsci.2019.06.023.10.1016/j.corsci.2019.06.023 ↗
42. C. Qiao, M. Wang, L. Hao, X. Jiang, X. Liu, C. Thee, and X. An: J. Alloys Compd., 2020, vol. 852, 156953. https://doi.org/10.1016/j.jallcom.2020.156953.10.1016/j.jallcom.2020.156953 ↗
43. K.S. Jyotheender, A. Gupta, and C. Srivastava: Materialia, 2020, vol. 9, 100617. https://doi.org/10.1016/j.mtla.2020.100617.10.1016/j.mtla.2020.100617 ↗
44. W. Yang, Z. Liu, and H. Huang: Corros. Sci., 2021, vol. 188, 109562. https://doi.org/10.1016/j.corsci.2021.109562.10.1016/j.corsci.2021.109562 ↗
45. S.R.F. Lala, A. Gupta, and C. Srivastava: Metall. Mater. Trans. A, 2022, vol. 53A, pp. 3795–806.10.1007/s11661-022-06786-z ↗
46. A. Gupta and C. Srivastava: Corros. Sci., 2022, vol. 194, p. 1009945. https://doi.org/10.1016/j.corsci.2021.109945.10.1016/j.corsci.2021.109945 ↗
47. A.P. Singh, A. Gupta, K.S. Jyotheender, and C. Srivastava: Metall. Mater. Trans. A, 2022, vol. 53A, pp. 2743–53.10.1007/s11661-022-06704-3 ↗
48. K.S. Jyotheender, S. Arora, and C. Srivastava: J. Alloys Compd., 2021, vol. 854, 157299. https://doi.org/10.1016/j.jallcom.2020.157299.10.1016/j.jallcom.2020.157299 ↗
49. S.R.F. Lala, A.P. Singh, S. Singh, S.C. Tiwari, and C. Srivastava: Materialia, 2023, vol. 27, 101709. https://doi.org/10.1016/j.mtla.2023.101709.10.1016/j.mtla.2023.101709 ↗
50. S.Y. Venkat, S.R.F. Lala, A.P. Singh, and C. Srivastava: J. Electron. Mater., 2023, vol. 52, pp. 3797–806. https://doi.org/10.1007/s11664-023-10352-7.10.1007/s11664-023-10352-7 ↗
51. K.S. Jyotheender, A. Gupta, and C. Srivastava: Materialia, 2020, vol. 9, p. 1000617. https://doi.org/10.1016/j.mtla.2020.100617.10.1016/j.mtla.2020.100617 ↗
52. A. Hadadzadeh, F. Mokdad, M.A. Wells, and D.L. Chen: Mater. Sci. Eng. A, 2018, vol. 709, pp. 285–89.10.1016/j.msea.2017.10.062 ↗