journal article·2019-11Open access

Estimation of the Temperature in the Stirred Zone and Cooling Rate of Friction Stir Welding of EH46 Steel from TiN Precipitates

Montadhar Al-moussawi, Alan J. Smith, Masoumeh Faraji, Stephen Cater

Abstract

Measuring the peak temperature in the contact region of the tool/workpiece in friction stir\ud 11 welding (FSW) is difficult using conventional methods such as use of thermocouples or a\ud 12 thermal imaging camera, hence an alternative method is required to tackle this problem. The\ud 13 objective of the present work was to estimate more accurately, for the first time, the peak\ud 14 temperature and cooling rate of FSW from precipitation of TiN in friction stir welded steel\ud 15 samples. Microstructures of nine friction stir welded samples of high strength shipbuilding\ud 16 steel of EH46 grade were examined closely by SEM-EDS to detect the TiN precipitates.\ud 17 Thermal heat treatments using an accurate electrical digital furnace were also carried out on\ud 18 80 unwelded EH46 steel samples over a range of temperatures and cooling rates. Heat\ud 19 treatments were to create a basis to understand TiN precipitation behavior under various\ud 20 heating and cooling regimes for the studied alloy. Heat treatment showed that TiN particles\ud 21 can precipitate at a peak temperature exceeding 1000°C and the size of TiN precipitates\ud 22 particles increases with decreasing cooling rate. In a temperature range between 1100-1200°C\ud 23 the TiN precipitates were accompanied by other elements such as Nb, S, Al and V. Pure TiN\ud 24 particles were found after the peak temperature exceeded 1250°C with limited precipitation\ud 25 after reaching a peak temperature of 1450°C. The comparison between the friction stir\ud 26 welding samples and the heat treatments in terms of types and sizes of TiN precipitates\ud 27 suggests that the welding peak temperature should have been in the range of 1200-1350°C\ud 28 with a cooling rate in the range of 20-30 K/sec. The current work represents a step change in\ud 29 estimating the friction stir welding temperature and cooling rate which are difficult to\ud 30 determine using thermocouples and thermal imaging camera.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. W.M. Thomas, E.D. Nicholas, J.C. Needham, M.G. Murch, P. Templesmith, and C.J. Dawes: Friction Stir Butt Welding, International Patent No. PCT/GB92/02203, 1991.
2. S.A. Hussein, S. Thiru, R. Izamshah and A.S.M.D. Tahir: Advances in Mat. Sci. & Eng., 2014, 8 pages.10.1155/2014/980636 ↗
3. 3. P. Carlone and G.S. Palazzo: Metallogr. Microstruct. Anal., 2013, vol. 2, pp. 213-222.10.1007/s13632-013-0078-4 ↗
4. 4. J. Mezyk and S. Kowieski: Solid State Phenomena, 2015, vol. 220-221, pp. 859-863.10.4028/www.scientific.net/SSP.220-221.859 ↗
5. 5. Z.H. Zhang, W.Y. Li, J.L. Li and Y.J. Chao: Int. J. Adv. Manuf. Technol., 2014, vol. 73, pp. 1213-1218.10.1007/s00170-014-5926-0 ↗
6. 6. A. Arora, T. DebRoy and K.H.D.H. Bhadeshia: Acta Mater., 2011, vol. 59, pp. 2020-2028.10.1016/j.actamat.2010.12.001 ↗
7. 7. L. Wang, C.M. Davies, R.C. Wimpory, L.Y. Xie and K.M. Nikbin: Materials at High Temperature, 2010, vol. 27, pp. 167-178.10.3184/096034010X12813743510192 ↗
8. J Stock, CM Enloe, RJ OMalley, KO Findley (2014) AIST Trans. 11:180-186.
9. 9. M.T. Nagata, J.G. Speer and D.K. Matlock: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 3099-3110.10.1007/s11661-002-0294-z ↗
10. KA El-Fawakhry, MF Mekkawy, ML Mishreky, MM Eissa (1991) ISIJ Int. 31: 1020-1025.10.2355/isijinternational.31.1020 ↗
11. 11. M.L. Wang, G.G. Cheng, S.T. Qiu, P. Zhao, and Y. Gan: International Journal of Minerals, Metallurgy and Materials, 2010, vol.17, pp. 276-281.10.1007/s12613-010-0305-9 ↗
12. 12. S.G. Hong, H.J Jun, K.B. Kang and C.G. Park: Scr. Mater., 2003, vol. 48, pp. 1201–1206.10.1016/S1359-6462(02)00567-5 ↗
13. D.M. Failla: Friction Stir Welding and Microstructure Simulation of HSLA-65 and Austenitic Stainless Steels, MSc Thesis, The Ohio State University, 2009.
14. 14. S.F. Medina, A. Quispe and M. Gomez: Metall. Mater. Trans. A., 2014, vol. 45A, pp. 1524–1539.10.1007/s11661-013-2068-1 ↗
15. Z.H. Zhu and S.T. Qiu (2012) Adv. Mater. Res. 535:633-638.10.4028/www.scientific.net/AMR.535-537.633 ↗
16. 16. P. Gong, E.J. Palmiere and W.M. Rainforth: Acta Mater., 2015, vol. 97, pp. 392-403.10.1016/j.actamat.2015.06.057 ↗
17. 17. L.J. Cuddy: “The Effect of Microalloy Concentration on the Recrystallization of Austenite During Hot Deformation”, In: A. J. DeArdo, G. A. Ratz, and P. J. Wray, eds. Thermomechanical processing of microalloyed austenite. Pittsburgh, USA: TMS-AIME, 1981: 129-140.
18. 18. J. Fernández, S. Illescas and J.M. Guilemany: Mater. Letters, 2007, vol. 61, pp. 2389–2392.10.1016/j.matlet.2006.09.021 ↗
19. 19. A. Karmakar, S. Kundu, S. Roy, S. Neogy, D. Srivastava and D. Chakrabarti: Mater. Sci. Tech., 2014, vol. 30, pp. 653-664.10.1179/1743284713Y.0000000386 ↗
20. 20. J. Kunze, C. Mickel, G. Backmann, B. Beyer, M. Reibold, C. Klinkenberg, Steel Research, 1997, vol. 68 (10), pp. 441-449.10.1002/srin.199700580 ↗
21. 21. T-P Qu, J. Tian, K-I Chen, Z Xu, D-Y Wang: Ironmaking & Steelmaking, 2019, vol. 46 (4), pp. 353-358.10.1080/03019233.2017.1396722 ↗
22. 22. S.F. Di Martino and G. Thewlis: Metall. Mater. Trans. A., 2014, vol. 45A, pp. 579-594.10.1007/s11661-013-2035-x ↗
23. 23. A.J. DeArdo: International Materials Reviews, 2003, vol. 48, pp. 371–402.10.1179/095066003225008833 ↗
24. G Stein, W Kirschner, J Lueng (1997) Application of nitrogen-alloyed martensitic stainless steels in the aviation industry. In: E.G. Nisbett and A.S. Melilli (eds) Steel Forgings: Second Volume. ASTM Special Technical Publication, Warrendale, PA, pp. 104-115.10.1520/STP16596S ↗
25. 25. T. Shiraiwa and N. Fujino, “Electron Probe Microanalysis of Ti(C, N) and Zr(C, N) in Steel”, 1969, In: Möllenstedt G., Gaukler K.H. (eds) Vth International Congress on X-Ray Optics and Microanalysis, Springer, Berlin, Heidelberg, pp 531-534.
26. 26. M. Hua, C.I. Garcia, and A.J. DeArdo: Metall. Mat. Trans. A, 1997, vol. 28A, pp. 1769-80.10.1007/s11661-997-0108-4 ↗
27. 27. H. Schmidt and J. Hattel: Modelling and Simulation in Materials Science and Engineering, 2005, vol. 13, pp.77–93.10.1088/0965-0393/13/1/006 ↗
28. 28. H.B. Schmidt and J.H. Hattel: Scri. Mater., 2008, vol. 58, pp.332–337.10.1016/j.scriptamat.2007.10.008 ↗
29. 29. P.A. Colegrove, H.R. Shercliff and R. Zettler: Science and Technology of Welding and Joining, 2007, vol. 12, pp. 284-297.10.1179/174329307X197539 ↗
30. R.K. Gibbs, R.C. Peterson, and B.A. Parker: Proc. Int. Conf. on Processing, Microstructure and Properties of Microalloyed and Other Modern High Strength Low Alloy Steels, Iron and Steel Society, Warrendale, PA, 1992, pp. 201–07.
31. 31. S. Matsuda and K. Okumura: Trans. Iron Steel Inst. Jpn., 1978, vol. 18, p. 198.10.2355/isijinternational1966.18.198 ↗