EIS Behavior of Experimental High-Strength Steel in Near-Neutral pH and Load Conditions
Source abstract
Abstract
Two thermomechanical heat treatments were applied to a high-strength low carbon steel with an experimental chemical composition, and as a result two different microstructures were obtained. Steel A had a ferritic microstructure, and steel B had a bainitic-martensitic one. The corrosion behavior was reviewed at long times in samples without load by means of Electrochemical Impedance Spectroscopy (EIS) in a near-neutral pH (NNpH) environment. The results showed that the quantity and adherence of corrosion products on the sample surface at long times are different. Hence, the impedance was higher for steel B. Slow strain rate testing (SSRT) was applied to tempered samples of the two steels at 473 K, 673 K, and 873 K (200 °C, 400 °C, and 600 °C), and the corrosion behavior was acquired using EIS at the same time as the SSRT in NNpH conditions. This is a novel result because the tension samples were not electrically isolated from the rest of the load frame. The impedance for the ferritic steel was higher than the bainitic–martensitic one, while it slightly decreased for both steel over time. Tempering improved the corrosion resistance for steel A, while it was not modified for steel B. The corrosion behavior could be associated with the susceptibility of these steels to stress corrosion cracking. A transmission line model was proposed to show qualitatively the corrosion behavior of a crack in the steel, if there is a potential profile inside the crack. A hypothetical potential profile was acquired as well as different impedance behaviors based on electrochemical variables.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Corrosion Behavior and Inhibition · Hydrogen embrittlement and corrosion behaviors in metals · Concrete Corrosion and Durability
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (53)
Show source-provided references
1. R.H. Jones: Corrosion, American Society for Metals, Cleveland, OH, 1987.
2. R. N. Parkins, W. K. Blanchard and B. S. Delanty, Corrosion 1994, vol. 50, pp. 394-408.10.5006/1.3294348 ↗
3. Y.Z. Jia, J. Q. Wang, E. H. Han and W. Ke, J. Mater. Sci. Technol. 2011, vol. 27, pp. 1039-1046.10.1016/S1005-0302(11)60184-9 ↗
4. R.N. Parkings: in Corosion, NACE, Houston, 2000.
5. N. Winzer, A. Atrens, G. Song, E. Ghali, W. Dietzel, K. Kainer, U. Thinsp, N. Hort, and C. Blawert, Adv. Eng. Mater. 2005, vol. 7, pp. 659-693.10.1002/adem.200500071 ↗
6. T. D. Burleigh, Corrosion 1991, vol. 47, pp. 89-98.10.5006/1.3585235 ↗
7. B.T. Lu, J.L. Luo and P.R. Norton, Corros. Sci. 2010, vol. 52, pp. 1787-1795.10.1016/j.corsci.2010.02.020 ↗
8. Z. Y. Liu, X.G. Li and Y. F. Cheng, Electrochem. Commun. 2010, vol. 12, pp. 936-938.10.1016/j.elecom.2010.04.025 ↗
9. A. Shahriari, T. Shahrabi and A. A. Oskuie, J. of Materi Eng and Perform 2013, vol. 22, pp. 1459-1470.10.1007/s11665-012-0418-6 ↗
10. Z. Y. Liu, X. G. Li and Y. F. Cheng, J. of Materi Eng and Perform 2011, vol. 20, pp. 1242-1246.10.1007/s11665-010-9770-6 ↗
11. L. Y. Xu and Y. F. Cheng, Corros Sci 2012, vol. 59, pp. 103-109.10.1016/j.corsci.2012.02.022 ↗
12. Digby D. MacDonald and Mirna Urquidi-MacDonald, Corros Sci 1991, vol. 32, pp. 51-81.10.1016/0010-938X(91)90063-U ↗
13. J. G. Gonzalez-Rodriguez, M. Casales, V. M. Salinas-Bravo, J.L. Albarran and L. Martinez, Corrosion 2002, vol. 58, pp. 584-590.10.5006/1.3277649 ↗
14. D.D. Macdonald: in Pure and Applied Chemistry, 1999, p. 951.10.1351/pac199971060951 ↗
15. D.R. McIntyre, R.D. Kane and S.M. Wihelm, Corrosion 1988, vol. 44, p. 920.10.5006/1.3584966 ↗
16. W. Chen, R. Kania, R. Worthingham and G. Van Boven, Acta Mater 2009, vol. 57, pp. 6200-6214.10.1016/j.actamat.2009.08.047 ↗
17. R. W. Bosch, Corros Sci 2005, vol. 47, pp. 125-143.10.1016/j.corsci.2004.05.018 ↗
18. D. Phull: in Corrosion: Fundamentals, Testing, and Protection, ASM Handbook, ASM International, Materials Park, 2003, pp. 576–616.
19. D. Sprowls: in Metals Handbook. Corrosion, American Society of Metals, Cleveland, OH, 1994, pp. 363–415
20. R. Narayan, A. Kumar and K. P. Singh, Corros Sci 1985, vol. 25, pp. 449-&.10.1016/0010-938X(85)90041-1 ↗
21. A. Rauf, W. F. Bogaerts, and E. Mahdi, Corrosion 2012, vol. 68, 035002-1.10.5006/1.3691836 ↗
22. R. W. Bosch, F. Moons, J. H. Zheng and W. F. Bogaerts, Corrosion 2001, vol. 57, pp. 532-539.10.5006/1.3290379 ↗
23. J. G. Gonzalez-Rodriguez, M. Casales, V. M. Salinas-Bravo, M. A. Espinosa-Medina and A. Martinez-Villafane, J Solid State Electr 2004, vol. 8, pp. 290-295.10.1007/s10008-003-0450-4 ↗
24. R. W. Bosch, J. Hubrecht, W. F. Bogaerts and B. C. Syrett, Corrosion 2001, vol. 57, pp. 60-70.10.5006/1.3290331 ↗
25. J. J. Park, S. I. Pyun, K. H. Na, S. M. Lee and Y. T. Kho, Corrosion 2002, vol. 58, pp. 329-336.10.5006/1.3287682 ↗
26. Digby D. Macdonald, Electrochimica Acta 2006, vol. 51, pp. 1376-1388.10.1016/j.electacta.2005.02.107 ↗
27. Yu D. Morozov, I. A. Simbukhov and D. L. Dyakonov, Metallurgist 2012, vol. 56, pp. 510-518.10.1007/s11015-012-9607-7 ↗
28. S.C. Wang and P.W. Kao (1993) J. Mater. Sci. 28:5169-517510.1007/BF00570058 ↗
29. E. Keehan, L. Karlsson and H. O. Andrén, Science and Technology of Welding and Joining 2006, vol. 11, pp. 1-8.10.1179/174329306X77830 ↗
30. R. D. K. Misra, Z. Jia, R. O’Malley and S. J. Jansto, Materials Science and Engineering: A 2011, vol. 528, pp. 8772-8780.10.1016/j.msea.2011.08.047 ↗
31. C.A. Schneider, W.S. Rasband and Kevin W. Eliceiri, Nat Meth 2012, vol. 9, pp. 671-675.10.1038/nmeth.2089 ↗
32. T. Giordani, T. R. Clarke, C. E. F. Kwietniewski, M. A. Aronov, N. I. Kobasko and G. E. Totten, J. of Materi Eng and Perform 2013, vol. 22, pp. 2304-2313.10.1007/s11665-013-0522-2 ↗
33. J.I. Barraza-Fierro, B. Campillo-Illanes, X. Li and H. Castaneda, Metall and Mat Trans A 2014, vol. 45, pp. 3981-3994.10.1007/s11661-014-2320-3 ↗
34. E. Girault, P. Jacques, Ph Harlet, K. Mols, J. Van Humbeeck, E. Aernoudt and F. Delannay, Materials Characterization 1998, vol. 40, pp. 111-118.10.1016/S1044-5803(97)00154-X ↗
35. ASTM: in E8 Standard Test Method for Tension Testing of Metallic Materials, ASTM International, West Conshohockem, 2005.
36. 1280 Electrochemical Measurement Unit, Technical manual, Solartron Analytical, Hampshire, 2001.
37. M. Stern and A. L. Geary, Journal of The Electrochemical Society 1957, vol. 104, pp. 56-63.10.1149/1.2428496 ↗
38. J. R. Scully, Corrosion 2000, vol. 56, pp. 199-218.10.5006/1.3280536 ↗
39. A.C. Van Orden: NACE International.
40. 40. W. S. Zaengl, IEEE Electrical Insulation Magazine 2003, vol. 19, pp. 5-19.10.1109/MEI.2003.1238713 ↗
41. 41. J. Niu, J. I. Barraza-Fierro and H. Castaneda, Journal of Coatings Technology and Research 2015, vol. 12, pp. 393-405.10.1007/s11998-014-9627-2 ↗
42. ASTM: in E18 Standard Test Method for Rockwell Hardness and Rockwell Superficial Hardness of Metallic Materials, ASTM International, West Conshohocken, 2005.
43. A.K. Sinha: Ferrous Physical Metallurgy, Butterwsort, Boston, 1989.
44. A.A. Gorni and P.R. Mei, Journal of Materials Processing Technology 2004, vol. 155-156, pp. 1513-1518.10.1016/j.jmatprotec.2004.04.245 ↗
45. J.T. Bulger, B.T. Lu and J.L. Luo, J. Mater. Sci. 2006, vol. 41, pp. 5001-5005.10.1007/s10853-006-0131-7 ↗
46. H. F. Lopez, R. Bharadwaj, J. L. Albarran and L. Martinez, Metall and Mat Trans A 1999, vol. 30, pp. 2419-2428.10.1007/s11661-999-0250-2 ↗
47. B. T. Lu and J. L. Luo, Corrosion 2006, vol. 62, pp. 129-140.10.5006/1.3278258 ↗
48. G. R. Engelhardt, D. D. Macdonald and M. Urquidi-Macdonald, Corros Sci 1999, vol. 41, pp. 2267-2302.10.1016/S0010-938X(99)00058-X ↗
49. H. Marchebois, M. Keddam, C. Savall, J. Bernard and S. Touzain, Electrochimica Acta 2004, vol. 49, pp. 1719-1729.10.1016/j.electacta.2003.11.031 ↗
50. D. M. Bastidas, Corrosion 2007, vol. 63, pp. 515-521.10.5006/1.3278402 ↗
51. H. Keiser, K. D. Beccu and M. A. Gutjahr, Electrochimica Acta 1976, vol. 21, pp. 539-543.10.1016/0013-4686(76)85147-X ↗
52. K. Eloot, F. Debuyck, M. Moors and A. P. Van Peteghem, J Appl Electrochem 1995, vol. 25, pp. 326-333.10.1007/BF00249650 ↗
53. L. Y. Xu and Y. F. Cheng, Corrosion Science 2013, vol. 73, pp. 150-160.10.1016/j.corsci.2013.04.004 ↗