Automated SEM/EDS Analysis for Assessment of Trace Cross-Contamination in 316L Stainless Steel Powders
Source abstract
Abstract
Abstract Following observations of microcracking in two, out of three, Additive manufactured (AM) 316L steel samples, an investigation was undertaken to ascertain the root cause. Welding diagrams, taking into account composition and process parameters, could not generally account for the experimental observations of non-cracked versus cracked AM 316L samples. EBSD phase maps in all three AM samples exhibited a fully austenitic microstructure not only in the bulk sample but also near-surface. Analysis of microcracked regions in the AM samples showed the presence of local enrichment of Ni, Cu and P. Automated SEM/EDS analysis on feedstock powder samples prepared for cross-section examination revealed a fine, foreign particulate contaminant, expected to arise from NiCrCuP alloy cross-contamination during atomization, to be completely embedded in a 316L powder particle. This type of contamination would not have been revealed on examination of powder mounted onto a SEM stub, a common approach to assess powder quality. Based on this analysis, it is recommended to consider including automated SEM/EDS analysis on powder cross-sections in any standardization protocol for quality control of powders, to increase the chances of detection and identification of fine cross-contaminants. It is also recommended that atomization of NiCrCuP alloy should no longer precede atomization of 316L alloy.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Advanced materials and composites · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. J.R. Davis, ed., ASM Speciality Handbook. Stainless Steels, 2nd ed., ASM International, Materials Park, OH, 1994.
2. M.J. Heiden, L.A. Deibler, J.M. Rodelas, J.R. Koepke, D.J. Tung, D.J. Saiz, and B.H. Jared: Addit. Manuf., 2019, vol. 25, pp. 84–103. https://doi.org/10.1016/j.addma.2018.10.019.10.1016/j.addma.2018.10.019 ↗
3. A.S. Wu, D.W. Brown, M. Kumar, G.F. Gallegos, and W.E. King: Metall. Mater. Trans. A., 2014, vol. 45A(13), pp. 6260–70. https://doi.org/10.1007/s11661-014-2549-x.10.1007/s11661-014-2549-x ↗
4. U. Engström and E. Schneider: in World Congress on Powder Metallurgy, Proceedings of World PM2018, Beijing, China, 16-20 September 2018, pp. 43-52.
5. V. Polard and B. Blitz: in World Congress on Powder Metallurgy, Proceedings of World PM2018, Beijing, China, 16-20 September 2018, pp. 1152-55.
6. R. Goto: in World Congress on Powder Metallurgy, Proceedings of World PM2018, Beijing, China, 16-20 September 2018, pp. 1979-82.
7. P. Gundermann: in Euro PM2018 Plenary presentation, Bilbao, Spain, 14-18 October 2018. https://www.europm2018.com/onsite-content-access. Accessed 24 June 2021.
8. P. Bajaj, A. Hariharan, A. Kini, P. Kürnsteiner, D. Raabe, and E.A. Jägle: Mater. Sci. Eng. A., 2020, vol. 772, 138633. https://doi.org/10.1016/j.msea.2019.138633.10.1016/j.msea.2019.138633 ↗
9. N. Li, S. Huang, G. Zhang, R. Qin, W. Liu, H. Xiong, G. Shi, and J. Blackburn: J. Mater. Sci. Technol., 2019, vol. 35(2), pp. 242–69. https://doi.org/10.1016/j.jmst.2018.09.002.10.1016/j.jmst.2018.09.002 ↗
10. H. Fayazfar, M. Salarian, A. Rogalsky, D. Sarker, P. Russo, V. Paserin, and E. Toyserkani: Mater. Des., 2018, vol. 144, pp. 98–128. https://doi.org/10.1016/j.matdes.2018.02.018.10.1016/j.matdes.2018.02.018 ↗
11. J. Dawes, R. Bowerman, and R. Trepleton: Johnson Matthey Technol. Rev., 2015, vol. 59(3), pp. 243–56. https://doi.org/10.1595/205651315X688686.10.1595/205651315X688686 ↗
12. E. Santecchia, P. Mengucci, A. Gatto, E. Bassoli, L. Denti, F. Bondioli, and G. Barucca: in Euro PM2018 Proceedings, Bilbao, Spain, 14-18 October 2018.
13. C. Blackwell, S. Hall, J. Dawes, and N. Brierley: in Euro PM2018 Proceedings, Bilbao, Spain, 14-18 October 2018.
14. B. Mooney and K.I. Kourousis, Metals, 2020, vol. 10, 1273. https://doi.org/10.3390/met1009127310.3390/met10091273 ↗
15. M. Montazeri, R. Yavari, P. Rao, and P. Boulware: J. Manuf. Sci. Eng., 2018, vol. 140(11), 111001.https://doi.org/10.1115/1.404054310.1115/1.4040543 ↗
16. E. Santecchia, P. Mengucci, A. Gatto, E. Bassoli, L. Denti, B. Gheorghiu, and G. Barucca: in Euro PM2019 Proceedings, Maastricht, The Netherlands, 13-16 October 2019.
17. M. Horn, L. Langer, M. Schafnitzel, S. Dietrich, G. Schlick, C. Seidel, and G. Reinhart: Procedia CIRP, 2020, Vol. 94, pp. 167-72. In 11th CIRP Conference on Photonic Technologies, LANE 202010.1016/j.procir.2020.09.032 ↗
18. Virtual, Online, 7-10 September 2020.
19. J. Yu, M. Rombouts, and G. Maes: Mater. Des., 2013, vol. 45, pp. 228–35. https://doi.org/10.1016/j.matdes.2012.08.078.10.1016/j.matdes.2012.08.078 ↗
20. J.A. Brooks and A.W. Thompson: Int. Mater. Rev., 1991, vol. 36(1), pp. 16–24. https://doi.org/10.1179/imr.1991.36.1.16.10.1179/imr.1991.36.1.16 ↗
21. N. Suutala and T. Moisio: Solidification Technology in the Foundry and Casthouse, The Metals Society, London, 1980.
22. G. Pacary, M. Moline, and J.C. Lippold: EWI research brief no. B9008, 1990, Edison Welding Institute.
23. C.D. Lundin, C.H. Lee, and C.Y.P. Qiao: Group sponsored study-weldability and hot ductility behavior of nuclear grade austenitic stainless steels, Final report, Knoxville: Univ. of Tennessee, 1988.
24. E. Folkhard: Welding metallurgy of stainless steels, Springer Verlag, New York, 1988.10.1007/978-3-7091-8965-8 ↗
25. C.S. Freemantle, N. Sacks, M. Topic, and C.A. Pineda-Vargas: Int. J. Refract. Met. Hard Mater., 2014, vol. 44, pp. 94–102. https://doi.org/10.1016/j.ijrmhm.2014.01.019.10.1016/j.ijrmhm.2014.01.019 ↗
26. A. Gatto, E. Bassoli, and L. Denti: Addit. Manuf., 2018, vol. 24, pp. 13–9. https://doi.org/10.1016/j.addma.2018.09.004.10.1016/j.addma.2018.09.004 ↗
27. A.D. Brandão, R. Gerard, J. Gumpinger, S. Beretta, A. Makaya, L. Pambaguian, and T. Ghidini: Materials, 2017, vol. 10, 522, https://doi:https://doi.org/10.3390/ma1005052210.3390/ma10050522 ↗
28. E. Santecchia, P. Mengucci, A. Gatto, E. Bassoli, S. Defanti, and G. Barucca: Materials, 2019, vol. 12, 2342; https://doi:https://doi.org/10.3390/ma1215234210.3390/ma12152342 ↗
29. M.J. Balart, X. Hao, S. Marks, G.D. West, and C.L. Davis: in Euro PM2019 Proceedings, Maastricht, The Netherlands, 13-16 October 2019.
30. Y. Sun, R.J. Hebert, and M. Aindow: Mater. Des., 2017, vol. 140, pp. 153–62. https://doi.org/10.1016/j.matdes.2017.11.063.10.1016/j.matdes.2017.11.063 ↗
31. M.J. Balart, X. Hao, S. Marks, G.D. West, M. Walker, and C.L. Davis: Metall. Mater. Trans. A., 2020, vol. 51A(12), pp. 6439–60. https://doi.org/10.1007/s11661-020-06010-w.10.1007/s11661-020-06010-w ↗
32. S. Irukuvarghula, H. Hassanin, C. Cayron, M.M. Attallah, D. Stewart, and M. Preuss: Acta Mater., 2017, vol. 133, pp. 269–81. https://doi.org/10.1016/j.actamat.2017.04.068.10.1016/j.actamat.2017.04.068 ↗
33. M.J. Balart, H.G.C. Hamilton, X. Hao, M. Strangwood, and C.L. Davis: in Euro PM2018 Proceedings, Bilbao, Spain, 14-18 October 2018.
34. ASTM A240 / A240M–20a: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications, ASTM International, West Conshohocken, PA, 2020, www.astm.org.
35. W.T. DeLong: Welding Journal Res. Suppl., 1974, vol. 53, pp. 273s-s286.
36. A.L. Schaeffler: Met. Prog., 1949, vol. 56(11), pp. 680–8.
37. D.J. Kotecki and T.A. Siewert: Weld J., 1992, vol. 71(5), pp. 171–8.
38. O. Hammer and U. Svensson: Solidification and Casting of Metals, The Metals Society, London, 1979, pp. 401–10.
39. BS ISO 13322-1:2014: Particle size analysis - Image analysis methods – Part 1: Static image analysis methods, 2014, www.iso.org.
40. A. Jillavenkatesa, S.J. Dapkunas, and L.-S. H. Lum: NIST Recommended Practical Guide Special Publication 960-1, Particle Size Characterization, January 2001.