An Investigation into the Correlation of Small Punch and Uniaxial Creep Data for Waspaloy
Source abstract
Abstract
Abstract Within the aerospace sector, the understanding and prediction of creep strains for materials used in high-temperature applications, such as Nickel-based super alloys, is imperative. Small punch testing offers the potential for understanding creep behavior using much less material than conventional uniaxial testing but in contrast to uniaxial creep tests, the stress in small punch creep (SPC) tests is multiaxial. SPC testing can be a valuable tool for validating models of creep deformation, but the key to unlocking its full capability is through the accurate correlation of the creep material properties measured through both techniques. As such, the focus of this paper is to correlate the creep behavior of Waspaloy obtained through conventional uniaxial testing to that obtained via small punch creep testing. Recently, and for low chrome steels, this has been achieved through use of the k sp method, but there are good reasons for believing this technique will not work so well for Nickel-based super alloys. This paper shows this to be the case for Waspaloy and proposes some alternative methods of correlation based on combining the Monkman–Grant relation and the Wilshire equations for both uniaxial and small punch creep. It was found that this latter approach enabled the accurate conversion of SPC minimum displacement rates to equivalent uniaxial minimum creep rates which, when combined with the Wilshire equations, enabled SPC test loads to be converted into equivalent uniaxial stresses (and visa versa) with levels of accuracy that were significantly reduced when compared to using the k sp method. Further, the random error associated with these conversions were dramatically increased.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High Temperature Alloys and Creep · Fatigue and fracture mechanics · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. R.J. Lancaster, S.P. Jeffs: Small Punch Creep. Creep [Internet]. 2018; Available from: http://www.intechopen.com/books/creep/small-punch-creep.10.5772/intechopen.70375 ↗
2. C. Wen, T. Xu, K. Guan: Correlation factor study of small punch creep test and its life prediction, Materials. 2016, 9(10), 796.10.3390/ma9100796 ↗
3. 3. K. Matocha and R Hurst: Small punch testing-the transition from a code of practice to a European testing standard. In Key Engineering Materials, 2017, 3(22), 734.
4. 4. J. Chakrabarty: A theory of stretch forming over hemispherical punch heads, International Journal of Mechanical Science, 1970, 12(4), 315-325.10.1016/0020-7403(70)90085-8 ↗
5. 5. S.P. Jeffs, R.J. Lancaster, T.E. Garcia: Creep lifing methodologies applied to a single crystal superalloy by use of small scale test techniques. Materials Science Engineering A, 2015, 636, 529–35.10.1016/j.msea.2015.03.119 ↗
6. 6. K. Milička and F Dobeš: Small punch testing of P91 steel, International Journal of Pressure Vessel and Piping, 2006, 83, 625-63410.1016/j.ijpvp.2006.07.009 ↗
7. 7. R. J Lancaster, W.J. Harrison and G Norton: An analysis of small punch creep behaviour in the γ titanium aluminide Ti-45Al-2Mn-2Nb, Materials Science Engineering A, 2015, 626, 263-274.10.1016/j.msea.2014.12.045 ↗
8. 8. S. Holmström, Y. Li, P. Dymacek, E. Vacchieri, S.P. Jeffs, R.J. Lancaster, D. Omacht, Z. Kubon, E. Anelli, J. Rantala, A. Tonti, S. Komaz: Creep strength and minimum strain rate estimation from Small Punch creep tests, Materials Science Engineering A, 2018, 731, 161-172.10.1016/j.msea.2018.06.005 ↗
9. 9. M. Evans and D Wang: The small punch creep test: Some results from a numerical model, Journal of Materials Science, 2008, 43(6), 1825–35.10.1007/s10853-007-2388-x ↗
10. 10. G. Sundararajan: The Monkman–Grant relationship, Materials Science and Engineering A, 1989, 112, 205-214.10.1016/0921-5093(89)90360-2 ↗
11. 11. F. Dobeš and K. Milička: On the Monkman-grant relation for small punch test data. Materials Science Engineering A, 2002, 336(1-2), 245-24810.1016/S0921-5093(01)01975-X ↗
12. 12. B. Wilshire and A.J. Battenbough: Creep and creep fracture of polycrystalline copper, Materials Science and Engineering A, 2007, 443(1–2),156–66.10.1016/j.msea.2006.08.094 ↗
13. 13. R.W. Evans and B. Wilshire: Introduction to Creep, 1st Edition, 1993, Institute of Materials, London, 23–28.
14. 14. B. Wilshire and P.J. Scharning: Theoretical and practical approaches to creep of Waspaloy, Materials Science & Technology, 2009, 25(2), 242-248.10.1179/174328408X361508 ↗
15. 15. R.W. Evans, A constitutive model for the high-temperature creep of particle-hardened alloys based on the θ projection method, Proceedings of the Royal Society London - A, 2000, 456: 835-868.10.1098/rspa.2000.0539 ↗
16. CEN. Part A: A Code of Practice for Small Punch Creep Testing. Small Punch Test Method Met Mater. 2006.
17. S. H. Song, J. Wu, X.J. Wei, D. Kumar, S.J. Liu and L.Q. Weng: Creep property evaluation of a 2.25Cr-1Mo low alloy steel, Mater. Sci. Eng. A, 2010, 527(9):2398–403.10.1016/j.msea.2010.01.007 ↗
18. 18. M. Evans: The importance of creep strain in linking together the Wilshire equations for minimum creep rates and times to various strains (including the rupture strain): An illustration using 1CrMoV rotor steel, Journal of Materials Science., 2014, 49(1), 329–39. .10.1007/s10853-013-7709-7 ↗
19. 19. H. Theil: Applied Economic Forecasts, Amsterdam, North Holland, 1966.
20. M. Whittaker, W. Harrison, C. Deen, C. Rae, S. Williams: Creep deformation by dislocation movement in Waspaloy, Materials (Basel). 10 2017. https://doi.org/10.3390/ma10010061.10.3390/ma10010061 ↗
21. 21. M. Evans, T. Williams, International Journal of Pressure Vessels and Piping Assessing the capability of the Wilshire equations in predicting uniaxial creep curves : An application to Waspaloy, Int. J. Press. Vessel. Pip. 172 (2019) 153–165. https://doi.org/10.1016/j.ijpvp.2019.03.032.10.1016/j.ijpvp.2019.03.032 ↗
22. 22. S. Birosca, G. Liu, R. Ding, J. Jiang, T. Simm, C. Deen, M. Whittaker, The dislocation behavior and GND development in a nickel based superalloy during creep, Int. J. Plast. 118 (2019) 252–268. https://doi.org/10.1016/j.ijplas.2019.02.015.10.1016/j.ijplas.2019.02.015 ↗
23. 23. R.J. Lancaster, W.J. Harrison, G. Norton, Materials Science & Engineering A An analysis of small punch creep behavior in the γ titanium aluminide Ti – 45Al – 2Mn – 2Nb, Mater. Sci. Eng. A. 626 (2015) 263–274. https://doi.org/10.1016/j.msea.2014.12.045.10.1016/j.msea.2014.12.045 ↗
24. 24. W.J. Harrison, M.T. Whittaker, C. Deen, Creep behavior of Waspaloy under non-constant stress and temperature, Mater. Res. Innov. 17 (2013) 323–326.10.1179/1433075X13Y.0000000137 ↗