journal article·2020-04

Continuous Grain Size Gradients in Austenitic Incoloy 800H: Design, Processing, and Characterization

Catherine M. Bishop, Shaun P. Mucalo, Milo V. Kral, Daniel J. Lewis

Publisher page

Abstract

Grain size variations are common in thermomechanically processed alloys with non-uniform cold work. A method to produce samples with grain size gradients was developed using Incoloy 800H. Two tensile samples with non-uniform gages were designed with finite element analysis and manufactured. Measured strain profiles were consistent with designs, and maximum von Mises strains of $$({18.6 \pm 6.1})$$ and $$({13.6 \pm 4.6})$$ pct were obtained. After annealing, an area $${40 \, {\hbox {mm}} \times 5}\, {\hbox {mm}}$$ was mapped by electron backscatter diffraction. Totals of 2849 and 2569 grains were identified after merging twins. Both samples had duplex grain structures as defined in ASTM E1181. Grains were binned into 4 mm strips to evaluate the spatial grain size distribution. Grain size gradients of 0.0081 and 0.0112 $${\hbox {mm}^2/\hbox {mm}}$$ were obtained. Simulated grain growth of the linear gradient microstructure was consistent with accelerated growth predictions. This new method of making samples will enable laboratory studies of gradient grain size effects in realistic industrial alloy microstructures. Further, samples could be used for parallel, single specimen experiments on phenomena that depend on grain size such as complexion transitions and fatigue. Most importantly, high-throughput parallel testing of microstructures enabled by our method could accelerate materials discovery and qualification in fields such as high-entropy and nuclear alloys.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Entropy Alloys Studies · High Temperature Alloys and Creep · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (56)

Show source-provided references
1. W. D. Callister Jr., D. G. Rethwisch: Materials Science and Engineering: An Introduction, , Hoboken, NJ, 2014.
2. V. Cannillo, L. Lusvarghi, T. Manfredini, M. Montorsi, C. Siligardi, A. Sola: J. Eur. Ceram. Soc. 2007, vol. 27 (2), pp. 1293–1298.10.1016/j.jeurceramsoc.2006.05.033 ↗
3. A. Mortensen, S. Suresh: Int. Mater. Rev. 1995, vol. 40 (6), pp. 239–265.10.1179/imr.1995.40.6.239 ↗
4. S. Suresh, A. Mortensen: Int. Mater. Rev. 1997, vol. 42 (3), pp. 85–116.10.1179/imr.1997.42.3.85 ↗
5. A. R. Damodaran, S. Pandya, Y. Qi, S.-L. Hsu, S. Liu, C. Nelson, A. Dasgupta, P. Ercius, C. Ophus, L. R. Dedon, J. C. Agar, H. Lu, J. Zhang, A. M. Minor, A. M. Rappe, L. W. Martin: Nature Communications May 2017, vol. 8, pp. 14961.10.1038/ncomms14961 ↗
6. J. V. Mantese, A. L. Micheli, N. W. Schubring, R. W. Hayes, G. Srinivasan, S. P. Alpay: Appl. Phys. Lett. Aug. 2005, vol. 87 (8), pp. 082503.10.1063/1.2012526 ↗
7. J. Dossett: in Steel Heat Treating Fundamentals and Processes. ASM Handbook, vol. 4A. ASM International, Materials Park, OH, 201410.31399/asm.hb.v04a.9781627081658 ↗
8. J. K. Lee, F. R. Ehrlich, L. A. Crall, T. H. Collins: Metall. Trans. A 1988, vol. 19A (2), pp. 329–335.10.1007/BF02652542 ↗
9. K.-H. Hwang, M. R. Plichta, J. K. Lee: Mater. Sci. Eng. A May 1988, vol. 101, pp. 183–192.
10. K.-H. Hwang, M. R. Plichta, J. K. Lee: Mater. Sci. Eng. A 1989, vol. 114, pp. 61–71.10.1016/0921-5093(89)90845-9 ↗
11. J. Yan, J. Ma, J. Wang, Y. Shen: Metall. Mater. Trans. A 2018, vol. 49A (11), pp. 5333–5338.10.1007/s11661-018-4874-y ↗
12. J. Long, Q. Pan, N. Tao, M. Dao, S. Suresh, and L. Lu: Acta Mater. 2018
13. Z. Cheng, H. Zhou, Q. Lu, H. Gao, L. Lu: Science Nov. 2018, vol. 362 (6414), pp. eaau1925.10.1126/science.aau1925 ↗
14. P. Kodali, J.P. Richert: Failure mechanisms of alloy 800H in steam reformer furnace pigtails. in: CORROSION 2003: NACE International, 2003
15. ASME: Boiler and Pressure Vessel Code. Tech. Rep. Section VIII Division I. American Society of Mechanical Engineers, New York, NY, 2007
16. H. Almostaneer, H. Schrijen, K. Barai, A. Al-Meshari: Adv. Mater. Process. Technol. 2015, vol. 1 (1-2), pp. 56–66.
17. A. Baskaran, D. Crist, D. Lewis: Modell. Simul. Mater. Sci. Eng. Sep. 2017, vol. 25 (6), pp. 065010.10.1088/1361-651X/aa763c ↗
18. K. Brakke: Surface Evolver Manual. Susquehanna University, Selinsgrove, 2013
19. E04 Committee: ASTM E112-13: Test Methods for Determining Average Grain Size: Tech. Rep. ASTM International, West Conshohocken, PA, 2013
20. E04 Committee: ASTM E1382 - 97(2015): Test Methods for Determining Average Grain Size Using Semiautomatic and Automatic Image Analysis: Tech. Rep. ASTM International, West Conshohocken, PA, 2015
21. E04 Committee: ASTM E2627 - 13: Practice for Determining Average Grain Size Using Electron Backscatter Diffraction (EBSD) in Fully Recrystallized Polycrystalline Materials: Tech. Rep. ASTM International, West Conshohocken, PA 2013
22. E. Committee: ASTM E930 - Standard Test Methods for Estimating the Largest Grain Observed in a Metallographic Section (ALA Grain Size) - Engineering Workbench: Tech. Rep. ASTM International, West Conshohocken, PA 2018
23. E. Committee: ASTM E1181 - Standard Test Methods for Characterizing Duplex Grain Sizes - Engineering Workbench: Tech. Rep. ASTM International, West Conshohocken, PA, 2015
24. Incoloy alloy 800H & 800HT: Tech. Rep. SMC-047. Special Metals Corporation, New Hartford, NY 2004
25. W. Ren and R. Swindeman: A Review of Alloy 800H for Applications in the Gen IV Nuclear Energy Systems. in: ASME 2010 Pressure Vessels and Piping Division/K-PVP Conference. American Society of Mechanical Engineers, 2010, pp. 821–36.10.1115/PVP2010-25278 ↗
26. S. Watanabe, T. Shibasaki, and T. Hokamura: Remaining Life Estimation of Alloy 800H Pigtail Material During High Temperature Service. in: CORROSION 2018. NACE International, 2018
27. D. Drabble, C. Bishop, M. Kral: Metall. Mater. Trans. A 2011, vol. 42A (3), pp. 763–772.10.1007/s11661-010-0447-4 ↗
28. L. Tan, L. Rakotojaona, T. R. Allen, R. K. Nanstad, J. T. Busby: Mater. Sci. Eng. A 2011, vol. 528 (6), pp. 2755–2761.10.1016/j.msea.2010.12.052 ↗
29. E. Brünger, X. Wang, G. Gottstein: Scripta Mater. May 1998, vol. 38 (12), pp. 1843–1849.10.1016/S1359-6462(98)00124-9 ↗
30. Y. Cao, H. Di, J. Zhang, J. Zhang, T. Ma, R. D. K. Misra: Materials Science and Engineering: A 2013, vol. 585, pp. 71–85.10.1016/j.msea.2013.07.037 ↗
31. Y. Cao, H. Di, G. Huang: Journal of Nuclear Materials 2017, vol. 486, pp. 21–25.10.1016/j.jnucmat.2017.01.013 ↗
32. W. S. Chen, W. Kai, L. W. Tsay, J. J. Kai: Nucl. Eng. Des. 2014, vol. 272, pp. 92–98.10.1016/j.nucengdes.2014.01.022 ↗
33. A. L. Beardsley, C. M. Bishop, M. V. Kral: Metall. Mater. Trans. A 2019, vol. 50A (9), pp. 4098–4110.10.1007/s11661-019-05350-6 ↗
34. A. Beardsley, C. Bishop, M. Kral: Mater. Perform. Charact. 2016, vol. 5 (5), pp. 717–739.
35. Y. Cao, X. Shen, H. Di, G. Huang: J. Alloys Compd. 2017, vol. 698, pp. 304–316.10.1016/j.jallcom.2016.12.174 ↗
36. C. A. Schneider, W. S. Rasband, K. W. Eliceiri: Nat. Methods 2012, vol. 9, pp. 671–675.10.1038/nmeth.2089 ↗
37. MATLAB: Mathworks, 2015
38. G. Palumbo, K. T. Aust, E. M. Lehockey, U. Erb, P. Lin: Scripta Mater. May 1998, vol. 38 (11), pp. 1685–1690.10.1016/S1359-6462(98)00077-3 ↗
39. V. Randle: Acta Mater. Aug. 2004, vol. 52 (14), pp. 4067–4081.10.1016/j.actamat.2004.05.031 ↗
40. G. F. Vander Voort, J. J. Friel: Mater. Charact. Dec. 1992, vol. 29 (4), pp. 293–312.10.1016/1044-5803(92)90101-M ↗
41. N. F. Hurley: AAPG Bull. 1994, vol. 78 (8), pp. 1173–1185.
42. S. Wang, E. A. Holm, J. Suni, M. H. Alvi, P. N. Kalu, A. D. Rollett: Acta Mater. 2011, vol. 59 (10), pp. 3872–3882.10.1016/j.actamat.2011.03.011 ↗
43. L. Chen, J. Chen, R. A. Lebensohn, Y. Z. Ji, T. W. Heo, S. Bhattacharyya, K. Chang, S. Mathaudhu, Z. K. Liu, L. Q. Chen: Comput. Methods Appl. Mech. Eng. 2015, vol. 285, pp. 829–848.10.1016/j.cma.2014.12.007 ↗
44. T. Takaki, Y. Tomita: International Journal of Mechanical Sciences 2010, vol. 52 (2), pp. 320–328.10.1016/j.ijmecsci.2009.09.037 ↗
45. H. S. Zurob, Y. Bréchet, J. Dunlop: Acta Mater. 2006, vol. 54 (15), pp. 3983–3990.10.1016/j.actamat.2006.04.028 ↗
46. J. E. Hatch: Aluminum: Properties and Physical Metallurgy: Subsequent Edition, ASM International, Metals Park, OH, 1984.
47. M. E. Kassner: Fundamentals of Creep in Metals and Alloys, Butterworth-Heinemann, Waltham, MA, 2015.
48. A.C.E. Reid, R.C. Lua, R.E. Garcia, V.R. Coffman, S.A. Langer: Int. J. Mater. Prod. Technol., 2009
49. M.C. Mangalick and N.F. Fiore: Trans. Met. Soc. AIME, 1968, vol. 242, No. 11
50. M. E. Kassner, T. A. Hayes: Int. J. Plast. 2003, vol. 19 (10), pp. 1715–1748.10.1016/S0749-6419(02)00111-0 ↗
51. M. P. Petkov, J. Hu, E. Tarleton, A. C. F. Cocks: Int. J. Solids Struct. 2019, vol. 171, pp. 54–80.10.1016/j.ijsolstr.2019.05.006 ↗
52. G. Venkataramani, D. Deka, S. Ghosh: J. Eng. Mater. Technol. 2006, vol. 128 (3), pp. 356–365.10.1115/1.2204942 ↗
53. V. Herrera-Solaz, L. Patriarca, S. Foletti, J. Segurado, M. Niffenegger: Mater. Sci. Eng. A 2019, vol. 751, pp. 99–106.10.1016/j.msea.2019.02.063 ↗
54. D. B. Miracle, O. N. Senkov: Acta Mater. 2017, vol. 122, pp. 448–511.10.1016/j.actamat.2016.08.081 ↗
55. O. Muránsky, C. Yang, H. Zhu, I. Karatchevtseva, P. Sláma, Z. Nový, L. Edwards: Corros. Sci. 2019, vol. 159, pp. 108087.10.1016/j.corsci.2019.07.011 ↗
56. R. Wright, T.-L. Sham: Status of Metallic Structural Materials for Molten Salt Reactors: Tech. Rep. INL/EXT-18-45171. United States Department of Energy: Idaho National Laboratory May 201810.2172/1467482 ↗