journal article·2023-11

Hot Deformation Behavior and Microstructure of Cast Ni-Based Superalloy IN-100 Based on the Processing Map

Yusaku Hasebe, Takehito Hagisawa, Cheng Yang, Kenta Aoyagi, Kenta Yamanaka, Akihiko Chiba

Publisher page

Abstract

Hot compression tests were performed on a cast Ni-based superalloy IN-100 at various temperatures and strain rate ranges. From the flow stress-true strain curves and the microstructure observations, a processing map of the hot deformation was constructed based on the dynamic material model. At 1473 K, flow stresses showed a plateau region resembling the characteristics of a dynamic recovery, although values varied with the strain rate. The crystal orientation rotated from the initial <001> direction parallel to the compression axis to the <101> direction, which is the primary slip direction of the fcc system. Kink band formation was observed perpendicular to the compression axis, and fine discontinuous dynamic recrystallization at the boundary of the kink bands was observed for the slow strain rate. As the strain rate increased, meta-dynamic recrystallization was observed after the compression test. At 1373 K, the flow stress first increased sharply and then decreased gradually with increasing strain over the whole strain rate. Twin deformation was suggested to occur prior to the appearance of dynamic recrystallization under 1373 K for the low strain rate range. The stable region of hot deformation was considered to be located at approximately 1423 K and 0.003 s−1.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (50)

Show source-provided references
1. C.T. Sims: Superalloys 1984, TMS-AIME, Warrendale, 1984, pp. 399–419.
2. R.F. Fawley: in The superalloys. C.T. Sims and W.C. Hagel, eds., Wiley, Hoboken, 1972, p. 3.
3. A.M. Wusatowska-Sarnek, G. Ghosh, G.B. Olson, M.J. Blackburn, and M. Aindow: J. Mater. Res., 2003, vol. 18, pp. 2653–63.10.1557/JMR.2003.0371 ↗
4. R. Athey, and J. Moore: "Progress report on the gatorizing™ forging process, SAE Technical Paper 751047, 1975.10.4271/751047 ↗
5. A. Ota, N. Ueshima, K. Oikawa, and S. Imano: in Proceedings of the 9th international symposium on superalloy 718 & derivatives, 2018, pp. 987–99.10.1007/978-3-319-89480-5_66 ↗
6. Y. Li, X. Ye, J. Li, Y. Zhang, Y. Koizumi, and A. Chiba: Mater. Des., 2017, vol. 122, pp. 340–46.10.1016/j.matdes.2017.03.014 ↗
7. Y.V.R.K. Prasad, H.L. Gegel, S.M. Doraivelu, J.C. Malas, J.T. Morgan, K.A. Lark, and D.R. Barker: Metall. Trans. A, 1984, vol. 15, pp. 1883–92.10.1007/BF02664902 ↗
8. Y.V.R.K. Prasad: J. Mater. Eng. Perform., 2003, vol. 12, pp. 638–45.10.1361/105994903322692420 ↗
9. E. Onodera, S. Kurosu, Y. Li, H. Matsumoto, and A. Chiba: J. JSTP, 2010, vol. 51, pp. 227–32.10.9773/sosei.51.227 ↗
10. M.C. Somani, K. Muraleedharan, Y.V.R.K. Prasad, and V. Singh: Mater. Sci. Eng. A, 1998, vol. 245, pp. 88–99.10.1016/S0921-5093(97)00698-9 ↗
11. D. Rittel, L.H. Zhang, and S. Osovsk: J. Mech. Phys. Solids, 2017, vol. 107, pp. 96–114.10.1016/j.jmps.2017.06.016 ↗
12. H. Monajati, A.K. Taheri, M. Jahazi, and S. Yue: Metall. Mater. Trans. A, 2005, vol. 36, pp. 895–905.10.1007/s11661-005-0284-z ↗
13. Y. Li, E. Onodera, H. Matsumoto, K. Yamanaka, and A. Chiba: J. JSTP, 2010, vol. 51, pp. 221–26.10.9773/sosei.51.221 ↗
14. F. Montheillet, J.J. Jonas, and K.W. Neale: Metall. Mater. Trans. A, 1996, vol. 27, pp. 232–35.10.1007/BF02647764 ↗
15. B. Nithin, K. Chattopadhyay, and G. Phanikumar: Metall. Mater. Trans. A, 2018, vol. 49, pp. 4895–4905.10.1007/s11661-018-4795-9 ↗
16. H. Khorshidi, A. Kermanpur, H. Rastegari, E. Ghassemali, and M.C. Somani: Mater. Today Commun., 2021, vol. 27, p. 102352.10.1016/j.mtcomm.2021.102352 ↗
17. H. Ziegler: in Progress in solid mechanics, vol. 4, N. Sneddon and R. Hill, eds., North-Holland, Amsterdam, 1963, pp. 93–193.
18. H. Ziegler: in Progress in solid mechanics, vol. 4, I.N. Sneddon and R. Hill, eds., Wiley, New York, 1965, p. 191.
19. C.M. Sellars and W.J. McTegart: Acta Metall., 1966, vol. 14, pp. 1136–38.10.1016/0001-6160(66)90207-0 ↗
20. C. Phaniraj, D. Samantaray, S. Mandal, and A.K. Bhaduri: Mater. Sci. Eng. A, 2011, vol. 528, pp. 6066–71.10.1016/j.msea.2011.04.025 ↗
21. F. Kniepmeier, M. Gruendler, and H. Helfmaier: Z. Metallkd., 1976, vol. 67, pp. 533–37.
22. Q.L. Pan, B. Li, Y. Wang, Y.W. Zhang, and Z.M. Yin: Mater. Sci. Eng. A, 2013, vol. 585, pp. 371–78.10.1016/j.msea.2013.07.066 ↗
23. S.A. Sajjadi, A. Chaichi, H.R. Ezatpour, A. Maghsoudlou, and M.A. Kalaie: J. Mater. Eng. Perform., 2016, vol. 25, pp. 1269–75.10.1007/s11665-016-1967-x ↗
24. L. Ouyang, R. Luo, Y. Gui, Y. Cao, L. Chen, Y. Gui, H. Bian, K. Aoyagi, K. Yamanaka, and A. Chiba: Mater. Sci. Eng. A, 2020, vol. 788, p. 139638.10.1016/j.msea.2020.139638 ↗
25. T. Sakai and M. Ohashi: Mater. Sci. Technol., 1990, vol. 6, pp. 1251–57.10.1179/mst.1990.6.12.1251 ↗
26. T. Sakai, A. Belyakov, U. Kaibyshev, H. Miura, and J.J. Jonas: Prog. Mater. Sci., 2014, vol. 60, pp. 130–207.10.1016/j.pmatsci.2013.09.002 ↗
27. K. Huang and R.E. Logé: Mater. Des., 2016, vol. 111, pp. 548–74.10.1016/j.matdes.2016.09.012 ↗
28. K. Hagihara, R. Ueyama, M. Yamasaki, Y. Kawamura, and T. Nakano: Acta Mater., 2021, vol. 209, p. 116797.10.1016/j.actamat.2021.116797 ↗
29. K. Hagihara, T. Okamoto, M. Yamasaki, Y. Kawamura, and T. Nakano: Scripta Mater., 2016, vol. 117, pp. 32–36.10.1016/j.scriptamat.2016.02.016 ↗
30. M. Eskandari, M.A. Mohtadi-Bonab, A. Zarei-Hanzaki, J.A. Szpunar, and L.P. Karjalainen: Adv. Eng. Mater., 2018, vol. 20, p. 1800327.10.1002/adem.201800327 ↗
31. K. Higashida, J. Takamura, and N. Narita: Mater. Sci. Eng., 1986, vol. 81, pp. 239–58.10.1016/0025-5416(86)90266-1 ↗
32. S. Zherebtsov, N. Yurchenko, D. Shaysultanov, M. Tikhonovsky, G. Salishchev, and N. Stepanov: Adv. Eng. Mater., 2018, vol. 20, p. 1800327.10.1002/adem.201800327 ↗
33. J. Takamura: Bull. Jpn. Inst. Met., 1986, vol. 25, pp. 379–91.10.2320/materia1962.25.379 ↗
34. P. Poelt, C. Sommitsch, S. Mitsche, and M. Walter: Mater. Sci. Eng. A, 2006, vol. 420, pp. 306–14.10.1016/j.msea.2006.01.076 ↗
35. T. Sakai, M. Ohashi, K. Chiba, and J.J. Jonas: Acta Metall., 1988, vol. 36, pp. 1781–89.10.1016/0001-6160(88)90246-5 ↗
36. G.B. Olson and M. Cohen: Metall. Trans. A, 1976, vol. 7, pp. 1897–1904.
37. P. Caron: Proc. of the 9th int. symp. on superalloys, 2000, pp. 737–46.10.7449/2000/Superalloys_2000_737_746 ↗
38. A.P. Miodownik: Calphad, 1978, vol. 2, pp. 207–26.10.1016/0364-5916(78)90010-X ↗
39. M. Koyama, T. Sawaguchi, and K. Tsuzaki: Tetsu to Hagane, 2014, vol. 100, pp. 1253–60.10.2355/tetsutohagane.100.1253 ↗
40. A. Chiba, S. Lee, H. Matsumoto, and M. Nakamura: Mater. Sci. Eng. A, 2009, vol. 513–514, p. 286.10.1016/j.msea.2009.02.044 ↗
41. K. Yamanaka, M. Mori, S. Sato, and A. Chiba: Sci. Rep., 2017, vol. 7, p. 10808.10.1038/s41598-017-10305-1 ↗
42. M. Schneider and G. Laplanche: Acta. Mater., 2021, vol. 204, p. 116470.10.1016/j.actamat.2020.11.012 ↗
43. T.S. Byun: Acta. Mater., 2003, vol. 51, pp. 3063–71.10.1016/S1359-6454(03)00117-4 ↗
44. L. Remy: Acta Metall., 1977, vol. 26, pp. 443–51.10.1016/0001-6160(78)90170-0 ↗
45. J. Kear and J. Oblak: J. Pyhs. Colloq., 1974, vol. 35, pp. 35–45.
46. M. Kolbe: Mater. Sci. Eng., 2001, vol. A319–321, pp. 383–87.10.1016/S0921-5093(01)00944-3 ↗
47. L. Kovarik, R.R. Unocic, J. Li, P. Sarosi, C. Shen, Y. Wang, and M.J. Mills: Prog. Mater. Sci., 2009, vol. 54, pp. 839–73.10.1016/j.pmatsci.2009.03.010 ↗
48. D. Barba, E. Alabort, S. Pedrazzini, D.M. Collins, A.J. Wilkinson, P.A.J. Bagot, M.P. Moody, C. Atkinson, A. Jérusalem, and R.C. Reed: Acta Mater., 2017, vol. 135, pp. 314–29.10.1016/j.actamat.2017.05.072 ↗
49. D. Barba, S. Pedrazzini, A. Vilalta-Clemente, A.J. Wilkinson, M.P. Moody, P.A.J. Bagot, A. Jérusalem, and R.C. Reed: Scripta Mater., 2017, vol. 127, pp. 37–40.10.1016/j.scriptamat.2016.08.029 ↗
50. A. Guimier and J.L. Strudel: Proceedings of the 2nd international conference on strength of metals and alloys, ASM, Metals Park, 1970, p. 1145.