Triaxial Constraint and Tensile Strength Enhancement in Brazed Joints
Source abstract
Abstract
A brazed joint consists of a low-melting point and thin interlayer sandwiched between the high-melting-point base materials, in which the interlayer strength is typically lower than that of the base material. When this butt-joined composite is loaded uniaxially in the direction perpendicular to the plane of the brazing layer, the tensile strength is found to be much higher than that of the braze. This seems to violate the iso-stress condition in such a butt-joint serial configuration. The stress triaxiality has been usually ascribed, but without a quantitative rationalization, as being responsible for this tensile strength enhancement. Here a complete finite element simulation has been conducted to study the dependence of triaxiality and strength enhancement on geometric and material parameters. Two asymptotic limit solutions (based on Bridgman and Xia–Shih solutions, respectively) have been identified to understand the simulation results. The critical role of void evolution has been revealed when making a quantitative comparison to available experiments. In addition, ductility of the brazed joint, which has not been fully addressed in literature, is investigated by the Gurson–Tvergaard–Needleman model.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Structural Analysis and Optimization · Mechanical Behavior of Composites · Structural Analysis of Composite Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. R.S. Rosen and M.E. Kassner: ASM Handbook, ASM International, Cleveland, 1993, vol. 6, pp. 165–172.
2. American Welding Society (AWS) (2007) Brazing Handbook, American Welding Society, Miami.
3. T. Lienert, T. Siewert, S. Babu, and V. Acoff: ASM Handbook, ASM International, 2011, vol. 6A Welding Fundamentals and Processes.10.31399/asm.hb.v06a.9781627081740 ↗
4. J.W. Lee, J.H. McMurray, and J.A. Miller: Welding J. 1985, vol. 64, pp. 18-21.
5. T. Zaharinie, R. Moshwan, F. Yusof, M. Hamdi, and T. Ariga: Mater. Des. 2014, vol. 54, pp. 375-381.10.1016/j.matdes.2013.08.046 ↗
6. R.K. Shiue, S.K. Wu, and S.H. Yang: Metall. Mater. Trans. A 2017, vol. 48, pp. 735-744.10.1007/s11661-016-3890-z ↗
7. B.E. Riggs: Multi-scale computational modeling of Ni-base superalloy brazed joints for gas turbine applications. PhD Thesis, The Ohio State University, 2017.
8. M. Gao, B. Schneiderman, S.M. Gilbert, and Z. Yu: Metall. Mater. Trans. A 2019, vol. 50, pp. 5117-5127.10.1007/s11661-019-05386-8 ↗
9. M. Way, J. Willingham, and R. Goodall: Int. Mater. Rev. 2020, vol. 65, pp. 257-285.10.1080/09506608.2019.1613311 ↗
10. S.K. Tung, L.C. Lim, and M.O. Lai: Scripta Mater. 1995, vol. 33, pp. 1253-1259.10.1016/0956-716X(95)00352-V ↗
11. A. Elrefaey and W. Tillmann: J. Alloys Comp. 2009, vol. 487, pp. 639-645.10.1016/j.jallcom.2009.08.029 ↗
12. J. Ruiz-Vargas, N. Siredey-Schwaller, N. Gey, P. Bocher, and A. Hazotte: J. Mater. Process. Tech. 2013, vol. 213, pp. 20-29.10.1016/j.jmatprotec.2012.07.016 ↗
13. A.J. West, H.J. Saxton, A.S. Tetelman, and C.R. Barrett: Metall. Trans. 1971, vol. 2, pp. 1009-1017.10.1007/BF02664232 ↗
14. Y.H. Yu and M.O. Lai: J. Mater. Sci. 1995, vol. 30, pp. 2101-2107.10.1007/BF00353041 ↗
15. J. Mackerle: Modelling Simul. Mater. Sci. Eng. 1997, vol. 5, pp. 159-185.10.1088/0965-0393/5/2/006 ↗
16. Y.W. Lee, J.H. Kim, Y.S. Song, and C.S. Seok: Solid State Pheno. 2007, vols. 124-126, pp. 1673-1676.10.4028/www.scientific.net/SSP.124-126.1673 ↗
17. M.K. Ghovanlou, H. Jahed, and A. Khajepour: Eng. Fract. Mech. 2014, vol. 120, pp. 43-59.10.1016/j.engfracmech.2014.03.014 ↗
18. W. Jiang, W. Woo, and S.T. Tu: Mater. Des. 2015, vol. 72, pp. 63-71.10.1016/j.matdes.2015.01.011 ↗
19. V. Tvergaard: Adv. Appl. Mech. 1990, vol. 27, pp. 83-151.10.1016/S0065-2156(08)70195-9 ↗
20. Z. Xue, M.G. Pontin, F.W. Zok, and J.W. Hutchinson: Eng. Frac. Mech. 2010, vol. 77, 492-509.10.1016/j.engfracmech.2009.10.007 ↗
21. K.L. Nielsen and V. Tvergaard: Eng. Fract. Mech. 2010, vol. 77, 1031-1047.10.1016/j.engfracmech.2010.02.031 ↗
22. A.A. Benzerga, J.-P. Leblond, A. Needleman, and V. Tvergaard: Int. J. Fract. 2016, vol. 201, pp. 29-80.10.1007/s10704-016-0142-6 ↗
23. Y.F. Gao, Z. Xue, and Z. Yu: Ext. Mech. Lett. 2020, vol. 37, 100728.10.1016/j.eml.2020.100728 ↗
24. K.M. Flores and R.H. Dauskardt: Acta Mater. 2001, vol. 49, pp. 2527–2537.10.1016/S1359-6454(01)00125-2 ↗
25. W.D. Li, H. Bei, and Y.F. Gao: Intermetallics 2016, vol. 79, pp. 12-19.10.1016/j.intermet.2016.09.001 ↗
26. W.D. Li, Y.F. Gao, and H. Bei: Sci. Rep. 2016, vol. 6, 34878.10.1038/srep34878 ↗
27. Y.C. Zhao and Y.F. Gao: JOM 2020, vol. 72, pp. 877-882.10.1007/s11837-019-03949-z ↗
28. L. Xia and C.F. Shih: J. Mech. Phys. Solids 1995, vol. 43, pp. 233-259.10.1016/0022-5096(94)00064-C ↗
29. Y. Cui, Y.F. Gao, and H.B. Chew: Int. J. Solids Struct. 2020, vols. 200-201, pp. 188-197.10.1016/j.ijsolstr.2020.04.035 ↗
30. Y.F. Gao, H.T. Xu, W.C. Oliver, and G.M. Pharr: J. Mech. Phys. Solids 2008, vol. 56, pp. 402-416.10.1016/j.jmps.2007.05.015 ↗