Understanding the Material Flow Mechanisms—Microstructure Evolution—Defect Formation Relationships and Effects on Mechanical Properties in Friction Stir Welding of Dissimilar Aluminum Alloys
Source abstract
Abstract
The material flow mechanisms in large-thickness dissimilar friction stir welds have been determined in this study by systematically investigating the microstructure evolution in the weld’s nugget zone. Three wrought Al alloys (2024-T351, 6061-T651, and 7075-T735) have been selected and the effects of different processing conditions, material combinations, and material positions with respect to the tool’s motion—advancing and retreating sides—have been considered. A fundamental understanding of the underlying material flow mechanisms in friction stir welding of dissimilar Al alloys was developed, demonstrating key material and processing contributions with experimental results. The flow patterns and material mixing in dissimilar welds depend on the ability of the material on the retreating side to penetrate the advancing side material flow, where better mixing is achieved when the material having lower flow stress is located on the retreating side. The effects of the material flow and resulting weld microstructure on the defect formation mechanisms, weld quality, and mechanical properties were further evaluated across a broad range of processing parameters and material/position combinations. It was found that reduced tool rotation speed improves the weld quality, while increased traverse speed leads to higher weld strength. Digital image correlation was used to analyze tensile behavior of the dissimilar welds, and effective material mixing resulted in homogeneous strain distributions and the welds’ increased resistance to yielding. Using the integrated understanding of the material flow, microstructure evolution, and defect formation in dissimilar Al friction stir welding, optimization of the weld quality and mechanical properties will be discussed.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. R.S. Mishra and Z.Y. Ma: Mater. Sci. Eng. R Rep., 2005, vol. 50, pp. 1–78.10.1016/j.mser.2005.07.001 ↗
2. Z.Y. Ma, A.H. Feng, D.L. Chen, and J. Shen: Crit. Rev. Solid State Mater. Sci., 2018, vol. 43, pp. 269–333.10.1080/10408436.2017.1358145 ↗
3. L.E. Murr: J. Mater. Eng. Perform., 2010, vol. 19, pp. 1071–89.10.1007/s11665-010-9598-0 ↗
4. X. Wang, Y. Pan, and D.A. Lados: Metall. Mater. Trans. B, 2018, vol. 49B, pp. 2097–2117.10.1007/s11663-018-1290-z ↗
5. C. Genevois, A. Deschamps, A. Denquin, and B. Doisneau-cottignies: Acta Mater., 2005, vol. 53, pp. 2447–58.10.1016/j.actamat.2005.02.007 ↗
6. C. Gallais, A. Denquin, Y. Bréchet, and G. Lapasset: Mater. Sci. Eng. A, 2008, vol. 496, pp. 77–89.10.1016/j.msea.2008.06.033 ↗
7. J.-Q. Su, T.W. Nelson, R. Mishra, and M. Mahoney: Acta Mater., 2003, vol. 51, pp. 713–29.10.1016/S1359-6454(02)00449-4 ↗
8. W.-B. Lee, Y.-M. Yeon, and S.-B. Jung: Scr. Mater., 2003, vol. 49, pp. 423–28.10.1016/S1359-6462(03)00301-4 ↗
9. S.A. Khodir and T. Shibayanagi: Mater. Trans., 2007, vol. 48, pp. 1928–37.10.2320/matertrans.MRA2007042 ↗
10. R.M. Leal, C. Leitão, A. Loureiro, D.M. Rodrigues, and P. Vilaça: Mater. Sci. Eng. A, 2008, vol. 498, pp. 384–91.10.1016/j.msea.2008.08.018 ↗
11. C. Jonckheere, B. de Meester, A. Denquin, and A. Simar: J. Mater. Process. Technol., 2013, vol. 213, pp. 826–37.10.1016/j.jmatprotec.2013.01.001 ↗
12. M.J. Peel, A. Steuwer, P.J. Withers, T. Dickerson, Q. Shi, and H. Shercliff: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 2183–93.10.1007/BF02586138 ↗
13. A.A.M. da Silva, E. Arruti, G. Janeiro, E. Aldanondo, P. Alvarez, and A. Echeverria: Mater. Des., 2011, vol. 32, pp. 2021–27.10.1016/j.matdes.2010.11.059 ↗
14. S.T. Amancio-Filho, S. Sheikhi, J.F. dos Santos, and C. Bolfarini: J. Mater. Process. Technol., 2008, vol. 206, pp. 132–42.10.1016/j.jmatprotec.2007.12.008 ↗
15. J.F. Guo, H.C. Chen, C.N. Sun, G. Bi, Z. Sun, and J. Wei: Mater. Des., 2014, vol. 56, pp. 185–92.10.1016/j.matdes.2013.10.082 ↗
16. L. Giraud, H. Robe, C. Claudin, C. Desrayaud, P. Bocher, and E. Feulvarch: J. Mater. Process. Technol., 2016, vol. 235, pp. 220–30.10.1016/j.jmatprotec.2016.04.020 ↗
17. R. Bertrand, H. Robe, D. Texier, Y. Zedan, E. Feulvarch, and P. Bocher: J. Mater. Process. Technol., 2019, vol. 271, pp. 312–24.10.1016/j.jmatprotec.2019.03.027 ↗
18. S.A. Khodir and T. Shibayanagi: Mater. Sci. Eng. B, 2008, vol. 148, pp. 82–87.10.1016/j.mseb.2007.09.024 ↗
19. K. Jagathesh, M.P. Jenarthanan, P.D. Babu, and C. Chanakyan: Aust. J. Mech. Eng., 2017, vol. 15, pp. 19–26.10.1080/14484846.2015.1093229 ↗
20. M.R.M. Aliha, M. Shahheidari, M. Bisadi, M. Akbari, and S. Hossain: Int. J. Adv. Manuf. Technol., 2016, vol. 86, pp. 2551–65.10.1007/s00170-016-8341-x ↗
21. L.H. Ahmad Shah, S. Sonbolestan, A.R.H. Midawi, S. Walbridge, and A. Gerlich: Int. J. Adv. Manuf. Technol., 2019, vol. 105, pp. 889–904.10.1007/s00170-019-04287-9 ↗
22. S.-W. Song, B.-C. Kim, T.-J. Yoon, N.-K. Kim, I.-B. Kim, and C.-Y. Kang: Mater. Trans., 2010, vol. 51, pp. 1319–25.10.2320/matertrans.M2010032 ↗
23. S.-K. Park, S.-T. Hong, J.-H. Park, K.-Y. Park, Y.-J. Kwon, and H.-J. Son: Sci. Technol. Weld. Join., 2010, vol. 15, pp. 331–36.10.1179/136217110X12714217309696 ↗
24. V.R. Kishore, J. Arun, R. Padmanabhan, and V. Balasubramanian: Int. J. Adv. Manuf. Technol., 2015, vol. 80, pp. 91–98.10.1007/s00170-015-6995-4 ↗
25. U. Donatus, G.E. Thompson, X. Zhou, J. Wang, and K. Beamish: Mater. Des., 2015, vol. 83, pp. 203–213.10.1016/j.matdes.2015.06.006 ↗
26. X. Wang and D.A. Lados: Materialia, 2022, vol. 24, 101508.10.1016/j.mtla.2022.101508 ↗
27. D.R. Askeland, P.P. Fulay, and W.J. Wright: The Science and Engineering of Materials, 6th edn., Cengage Learning, 2010.
28. T. Sheppard and A. Jackson: Mater. Sci. Technol., 1997, vol. 13, pp. 203–209.10.1179/mst.1997.13.3.203 ↗
29. Z. Zhang, B.L. Xiao, D. Wang, and Z.Y. Ma: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 1717–26.10.1007/s11661-010-0545-3 ↗
30. M.-N. Avettand-Fènoël, R. Taillard, J. Laye, and T. Odièvre: Metall. Mater. Trans. A, 2014, vol. 45A, pp. 563–78.10.1007/s11661-013-2015-1 ↗
31. R. Nandan, G.G. Roy, T.J. Lienert, and T. DebRoy: Sci. Technol. Weld. Join., 2006, vol. 11, pp. 526–37.10.1179/174329306X107692 ↗
32. R. Nandan, G.G. Roy, and T. Debroy: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 1247–59.10.1007/s11661-006-1076-9 ↗
33. Y. Xiao, H. Zhan, Y. Gu, and Q. Li: Int. J. Heat Mass Transf., 2017, vol. 104, pp. 288–300.10.1016/j.ijheatmasstransfer.2016.08.047 ↗
34. P.L. Threadgill, A.J. Leonard, H.R. Shercliff, and P.J. Withers: Int. Mater. Rev., 2009, vol. 54, pp. 49–93.10.1179/174328009X411136 ↗
35. J.H. Ouyang and R. Kovacevic: J. Mater. Eng. Perform., 2002, vol. 11, pp. 51–63.10.1007/s11665-002-0008-0 ↗
36. M. Guerra, C. Schmidt, J.C. McClure, L.E. Murr, and A.C. Nunes: Mater. Charact., 2002, vol. 49, pp. 95–101.10.1016/S1044-5803(02)00362-5 ↗
37. Y. Pan and D.A. Lados: Metall. Mater. Trans. A, 2017, vol. 48A, pp. 1708–26.10.1007/s11661-016-3943-3 ↗
38. K. Kumar and S.V. Kailas: Mater. Sci. Eng. A, 2008, vol. 485, pp. 367–74.10.1016/j.msea.2007.08.013 ↗
39. Y. Tao, D.R. Ni, B.L. Xiao, Z.Y. Ma, W. Wu, R.X. Zhang, and Y.S. Zeng: Mater. Sci. Eng. A, 2017, vol. 693, pp. 1–3.10.1016/j.msea.2017.03.079 ↗
40. W.F. Xu, X.K. Wu, J. Ma, H.J. Lu, and Y.X. Luo: J. Mater. Res. Technol., 2019, vol. 8, pp. 6029–40.10.1016/j.jmrt.2019.09.077 ↗