High Temperature Fatigue Performance of Electron Beam Powder Bed Fusion Manufactured Alloy 718
Source abstract
Abstract
Abstract The microstructure and mechanical properties of additively manufactured (AM) parts have been shown to be different from that of cast and wrought counterparts. In this study, electron beam powder bed fusion (EB-PBF) fabricated Alloy 718 was exposed to three different heat treatment routes followed by strain-controlled fatigue testing at 550 °C. The fatigue tests were performed with specimens built with their center axis parallel and transverse relative to the build direction. The microstructure showed saturated precipitation ofδ-Ni3Nb after repeated solution treatment at 954 °C. In contrast, noδ-Ni3Nb precipitates could be observed after a single-step solution treatment at 1025 °C. However, the disparity of secondary phases showed no noticeable influence on the fatigue life. A significant difference in fatigue behavior was noted between the parallel and transverse directions. The specimens loaded parallel to the elongated grains showed on average ~5× greater life in comparison to the perpendicularly loaded specimens. Compared to corresponding heat-treated material conditions tested at ambient temperature, the specimens showed lower life at high strain amplitude and superior life at low strain amplitude. Moreover, competitive internal and surface failure modes were observed at the lower strain amplitudes while for the higher strain ranges, surface failure modes dominated.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (63)
Show source-provided references
1. C.K. Chua and K.F. Leong: in 3D Print. Addit. Manuf., 5th ed., World Scientific Publishing Company, Hackensack, NJ, 2017, pp. 137–96.
2. A. Saboori, A. Aversa, G. Marchese, S. Biamino, M. Lombardi, and P. Fino: Appl. Sci., 2019, vol. 9, p. 3316.10.3390/app9163316 ↗
3. V. Bhavar, P. Kattire, V. Patil, S. Khot, K. Gujar, and R. Singh: in Addit. Manuf. Handb., A.B. Badiru, V.V. Valencia, and D. Liu, eds., 1st ed., CRC Press, Boca Raton, FL, 2017, pp. 251–53.10.1201/9781315119106-15 ↗
4. A. Salmi, F. Calignano, M. Galati, and E. Atzeni: Virtual Phys. Prototype., 2018, vol. 13, pp. 191–202.10.1080/17452759.2018.1442229 ↗
5. L.J. Kumar and C.G. Krishnadas Nair: in Adv. 3D Print. Addit. Manuf. Technol., D.I. Wimpenny and P.M. Pandey, eds., 1st Edn. Springer, Singapore, 2017, pp. 39–54.10.1007/978-981-10-0812-2_4 ↗
6. E. Hosseini and V.A. Popovich: Addit. Manuf., 2019, vol. 30, p. 100877.
7. M.J. Donachie and S.J. Donachie: in Superalloys Tech. Guide, 2nd ed., ASM International, Materials Park, OH, 2002, pp. 1–9.10.31399/asm.tb.stg2.9781627082679 ↗
8. E.E. Brown and D.R. Muzyrka: in Superalloys II, C.T. Sims, N.S. Stoloff, and W.C. Hagel, eds., John Wiley & Sons, Inc., Hoboken, NJ, 1987, pp. 165–88.
9. G. Sjöberg, N. Ingesten, and R.G. Carlson: Superalloys, 1991, pp. 603–20.10.7449/1991/Superalloys_1991_603_620 ↗
10. B. Geddes, X. Huang, and H. Leon: in Superalloys Alloy. Perform., 1st ed., ASM International, Materials Park, OH, 2010, pp. 25–57.10.31399/asm.tb.sap.9781627083133 ↗
11. N. El-Bagoury, T. Matsuba, K. Yamamoto, H. Miyahara, and K. Ogi: Mater. Trans., 2005, vol. 46, pp. 2478–83.10.2320/matertrans.46.2478 ↗
12. M.A. Xavior, M. Manohar, P. Jeyapandiarajan, and P.M. Madhukar: Procedia Eng., 2017, vol. 174, pp. 1000–1008.10.1016/j.proeng.2017.01.252 ↗
13. GE Additive: n.d.
14. J. Kruth, S. Dadbakhsh, B. Vrancken, K. Kempen, J. Vleugels, and J. Humbeeck: in Addit. Manuf. Innov. Adv. Appl., T.S. Srivatsan and T.S. Sudarshan, eds., 1st ed., CRC Press, Boca Raton, FL, 2016, pp. 70–96.
15. R.M. Mahamood and E.T. Akinlabi: in Adv. Mater. Sci. Res., M.C. Wythers, ed., Nova Science Publishers, Inc, New York, NY, 2017, pp. 8–11.
16. C. Körner: Int. Mater. Rev., 2016, vol. 61, pp. 361–77.10.1080/09506608.2016.1176289 ↗
17. H. Helmer, C. Körner, and R.F. Singer: J. Mater. Res., 2014, vol. 29, pp. 1987–96.10.1557/jmr.2014.192 ↗
18. W.J. Sames, K.A. Unocic, R.R. Dehoff, T. Lolla, and S.S. Babu: J. Mater. Res., 2014, vol. 29, pp. 1920–30.10.1557/jmr.2014.140 ↗
19. W.J. Sames: Doctoral dissertation, Texas A & M University, 2015.
20. H. Helmer, A. Bauereiß, R.F. Singer, and C. Körner: Mater. Sci. Eng. A., 2016, vol. 668, pp. 180–87.10.1016/j.msea.2016.05.046 ↗
21. M.M. Kirka, K.A. Unocic, N. Raghavan, F. Medina, R.R. Dehoff, and S.S. Babu: JOM., 2016, vol. 68, pp. 1012–20.10.1007/s11837-016-1812-6 ↗
22. M.M. Kirka, Y. Lee, D.A. Greeley, A. Okello, M.J. Goin, M.T. Pearce, and R.R. Dehoff: JOM., 2017, vol. 69, pp. 523–31.10.1007/s11837-017-2264-3 ↗
23. D. Deng, J. Moverare, R.L. Peng, and H. Söderberg: Mater. Sci. Eng. A., 2017, vol. 693, pp. 151–63.10.1016/j.msea.2017.03.085 ↗
24. P. Karimi: PhD Thesis, University West, 2020.
25. M.M. Kirka, F. Medina, R. Dehoff, and A. Okello: Mater. Sci. Eng. A., 2017, vol. 680, pp. 338–46.10.1016/j.msea.2016.10.069 ↗
26. A.R. Balachandramurthi, J. Moverare, S. Mahade, and R. Pederson: Materials., 2018, vol. 12, p. 68.10.3390/ma12010068 ↗
27. D. Kotzem, P. Dumke, P. Sepehri, J. Tenkamp, and F. Walther: Prog. Addit. Manuf., 2020, vol. 5, pp. 267–76.10.1007/s40964-019-00101-w ↗
28. A. Strondl, M. Palm, J. Gnauk, and G. Frommeyer: Mater. Sci. Technol., 2011, vol. 27, pp. 876–83.10.1179/026708309X12468927349451 ↗
29. K. Unocic, L. Kolbus, R. Dehoff, S. Dryepondt, and B. Pint: in Corros. 2014, San Antonio, TX, 2014.
30. E. Sadeghi, P. Karimi, N. Israelsson, J. Shipley, T. Månsson, and T. Hansson: Addit. Manuf., 2020, vol. 36, p. 101670.
31. A.R. Balachandramurthi, J. Moverare, N. Dixit, D. Deng, and R. Pederson: Mater. Charact., 2019, vol. 149, pp. 82–94.10.1016/j.matchar.2019.01.018 ↗
32. A.R. Balachandramurthi, J. Moverare, N. Dixit, and R. Pederson: Mater. Sci. Eng. A., 2018, vol. 735, pp. 463–74.10.1016/j.msea.2018.08.072 ↗
33. D. Deng, R.L. Peng, and J. Moverare: Mater. Sci. Eng. A., 2019, vol. 760, pp. 448–57.10.1016/j.msea.2019.06.013 ↗
34. M.M. Kirka, D.A. Greeley, C. Hawkins, and R.R. Dehoff: Int. J. Fatigue., 2017, vol. 105, pp. 235–43.10.1016/j.ijfatigue.2017.08.021 ↗
35. A.R. Balachandramurthi, J. Moverare, T. Hansson, and R. Pederson: Int. J. Fatigue., 2020, vol. 141, p. 105898.10.1016/j.ijfatigue.2020.105898 ↗
36. ASTM Standard F3055 - 14a, ASTM International, West Conshohocken, PA, 2014.
37. ASTM Standard E606/E606M - 12, ASTM International, West Conshohocken, PA, 2012.
38. D. Deng, R.L. Peng, H. Söderberg, and J. Moverare: Mater. Des., 2018, vol. 160, pp. 251–61.10.1016/j.matdes.2018.09.006 ↗
39. G. Chen, S.Y. Zhao, P. Tan, J. Wang, C.S. Xiang, and H.P. Tang: Powder Technol., 2018, vol. 333, pp. 38–46.10.1016/j.powtec.2018.04.013 ↗
40. S. Tammas-Williams, P.J. Withers, I. Todd, and P.B. Prangnell: Scr. Mater., 2016, vol. 122, pp. 72–76.10.1016/j.scriptamat.2016.05.002 ↗
41. R. Cunningham, A. Nicolas, J. Madsen, E. Fodran, E. Anagnostou, M.D. Sangid, and A.D. Rollett: Mater. Res. Lett., 2017, vol. 5, pp. 516–25.10.1080/21663831.2017.1340911 ↗
42. A.A. Antonysamy, J. Meyer, and P.B. Prangnell: Mater. Charact., 2013, vol. 84, pp. 153–68.10.1016/j.matchar.2013.07.012 ↗
43. A.M. Rausch, M.R. Gotterbarm, J. Pistor, M. Markl, and C. Körner: Materials., 2020, vol. 13, p. 5517.10.3390/ma13235517 ↗
44. A. Strondl, R. Fischer, G. Frommeyer, and A. Schneider: Mater. Sci. Eng. A., 2008, vol. 480, pp. 138–47.10.1016/j.msea.2007.07.012 ↗
45. M.C. Flemings: Metall. Trans., 1974, vol. 5, pp. 2121–34.10.1007/BF02643923 ↗
46. M. Sundararaman, P. Mukhopadhyay, and S. Banerjee: Metall. Trans. A., 1988, vol. 19, pp. 453–65.10.1007/BF02649259 ↗
47. S. Ida, S. Kobayashi, and M. Takeyama: J. Alloys Compd., 2018, vol. 764, pp. 1033–38.10.1016/j.jallcom.2018.05.169 ↗
48. H.-Y. Bor, Chao-Nan Wei, H.T. Nguyen, An-Chou Yeh, and C.-M. Kuo: in Superalloy 718 Deriv., E. Ott, J. Groh, A. Banik, I. Dempster, T. Gabb, R. Helmink, X. Liu, A. Mitchell, G. Sjöberg, and A. Wusatowska-Sarnek, eds., Wiley, 2010, pp. 678–88.
49. N.S. Stoloff: in Superalloys II, C.T. Sims and W.C. Hagel, eds., John Wiley & Sons, Inc., Hoboken, NJ, 1987, pp. 61–96.
50. P. Rodriguez: Bull. Mater. Sci., 1984, vol. 6, pp. 653–63.10.1007/BF02743993 ↗
51. S.L. Mannan: Bull. Mater. Sci., 1993, vol. 16, pp. 561–82.10.1007/BF02757656 ↗
52. D. Fournier and A. Pineau: Metall. Trans. A., 1977, vol. 8, pp. 1095–105.10.1007/BF02667395 ↗
53. L. Xiao, D.L. Chen, and M.C. Chaturvedi: Scr. Mater., 2005, vol. 52, pp. 603–07.10.1016/j.scriptamat.2004.11.023 ↗
54. H.F. Merrick: Metall. Trans., 1974, vol. 5, pp. 891–97.10.1007/BF02643144 ↗
55. ASTM Standard E739 - 10, ASTM International, West Conshohocken, PA, 2015.
56. Q. Kawagoishi, D. Chen, and G. Nisitani: Fatigue Fract. Eng. Mater. Struct., 2000, vol. 23, pp. 209–16.10.1046/j.1460-2695.2000.00263.x ↗
57. S. Gribbin, S. Ghorbanpour, N.C. Ferreri, J. Bicknell, I. Tsukrov, and M. Knezevic: Mater. Charact., 2019, vol. 149, pp. 184–97.10.1016/j.matchar.2019.01.028 ↗
58. P.D. Nezhadfar, A.S. Johnson, and N. Shamsaei: Int. J. Fatigue., 2020, vol. 136, p. 105598.10.1016/j.ijfatigue.2020.105598 ↗
59. D. Gustafsson, J. Moverare, S. Johansson, M. Hörnqvist, K. Simonsson, S. Sjöström, and B. Sharifimajda: Procedia Eng., 2010, vol. 2, pp. 1095–1104.10.1016/j.proeng.2010.03.118 ↗
60. G.T. Cashman: Int. J. Fatigue., 2010, vol. 32, pp. 492–96.10.1016/j.ijfatigue.2009.04.018 ↗
61. W. Li, R. Sun, T. Hu, X. Li, C. Li, Y. Zhang, X. Ding, and P. Wang: Int. J. Fatigue., 2021, vol. 148, p. 106250.10.1016/j.ijfatigue.2021.106250 ↗
62. J.C. Stinville, E. Martin, M. Karadge, S. Ismonov, M. Soare, T. Hanlon, S. Sundaram, M.P. Echlin, P.G. Callahan, W.C. Lenthe, V.M. Miller, J. Miao, A.E. Wessman, R. Finlay, A. Loghin, J. Marte, and T.M. Pollock: Acta Mater., 2018, vol. 152, pp. 16–33.10.1016/j.actamat.2018.03.035 ↗
63. G.T. Cashman: J. Eng. Mater. Technol., 2007, vol. 129, pp. 293–303.10.1115/1.2712468 ↗