journal article·2021-09Open access

Microstructure Evolution and Tensile Properties of Cold-Rolled and Annealed Fe-30Mn-0.14C-7Cr-0.26Ni Steel

Xiaoman Chen, Jiaxin Zhang, Jianchao Xiong, Yuhui Wang, Yubin Zhang, Tiansheng Wang, Yan Peng

Abstract

The carbide precipitation, microstructure evolution, and tensile properties of Fe-30Mn-0.14C-7Cr-0.26Ni (in wt pct) steel after cold rolling to 95 pct reduction followed by annealing at temperatures ranging from 600 °C to 900 °C for 1 hour were investigated. The results show that, when the annealing temperature is increased from 600 °C to 900 °C, the grain size increases from 0.65 ± 0.30 to 5.75 ± 3.87 μm. When the annealing temperature is 600 °C, Cr23C6 carbides begin to precipitate. When the annealing temperature is increased from 600 °C to 800 °C, the average size of carbides increases from 39 to 69 nm. When the annealing temperature is increased to 900 °C, no carbides are produced due to the increased solubility of C in the austenite matrix. Ultrafine grains (~ 0.8 ± 0.58 μm) with a large amount of nanoscale carbides (~ 53 ± 21.8 nm) were obtained after annealing at 700 °C, resulting in a good combination of yield strength (679 MPa) and total elongation (38.4 pct). The fraction of deformation twins within the samples under different tensile strains was calculated, and it was revealed that grain refinement can seriously inhibit the generation of deformation twins. In addition, it has been found that grain refinement strengthening, precipitation strengthening, and dislocation strengthening have significant effects on yield strength, while the effects of solution strengthening and lattice friction are relatively weaker.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (61)

Show source-provided references
1. O. Grässel, L. Krüger, G. Frommeyer, and L.W. Meyer: Int. J. Plast., 2000, vol. 16, pp. 1391–1409.10.1016/S0749-6419(00)00015-2 ↗
2. C. Haase, S.G. Chowdhury, L.A. Barrales-Mora, D.A. Molodov, and G. Gottstein: Metall. Mater. Trans. A, 2012, vol. 43A, pp. 911–22.
3. O. Bouaziz, S. Allain, C.P. Scott, P. Cugy, and D. Barbier: Curr. Opin. Solid State Mater. Sci., 2011, vol. 15, pp. 141–68.10.1016/j.cossms.2011.04.002 ↗
4. Y. Lü, D.A. Molodov, and G. Gottstein: Acta Mater., 2011, vol. 59, pp. 3229–43.10.1016/j.actamat.2011.01.063 ↗
5. M. Koyama, Y. Shimomura, A. Chiba, E. Akiyama, and K. Tsuzaki: Scripta Mater., 2017, vol. 141, pp. 20–23.10.1016/j.scriptamat.2017.07.017 ↗
6. J. Hufenbach, F. Kochta, H. Wendrock, A. Voss, L. Giebeler, S. Oswald, S. Pilz, U. Kühn, A. Lode, M. Gelinsky, and A. Gebert: Mater. Des., 2018, vol. 142, pp. 22–35.10.1016/j.matdes.2018.01.005 ↗
7. L. Bracke, K. Verbeken, L. Kestens, and J. Penning: Acta Mater., 2009, vol. 57, pp. 1512–24.10.1016/j.actamat.2008.11.036 ↗
8. H. Li, F. Yin, T. Sawaguchi, K. Ogawa, X. Zhao, and K. Tsuzaki: Mater. Sci. Eng. A, 2008, vol. 49, pp. 4217–26.
9. V. Shterner, I.B. Timokhina, and H. Beladi: Mater. Sci. Eng. A, 2016, vol. 669, pp. 437–46.10.1016/j.msea.2016.05.104 ↗
10. I. Gutierrez-Urrutia and D. Raabe: Acta Mater., 2012, vol. 60, pp. 5791–5802.10.1016/j.actamat.2012.07.018 ↗
11. K. Renard and P.J. Jacques: Mater. Sci. Eng. A, 2012, vol. 542, pp. 8–14.10.1016/j.msea.2012.01.123 ↗
12. H.Z. Wang, P. Yang, W.M. Mao, and F.Y. Lu: J. Alloys Compds., 2013, vol. 558, pp. 26–33.10.1016/j.jallcom.2012.12.032 ↗
13. J.B. Seol, J.E. Jung, Y.W. Jang, and C.G. Park: Acta Mater., 2013, vol. 61, pp. 558–78.10.1016/j.actamat.2012.09.078 ↗
14. V. Shterner, I.B. Timokhina, and H. Beladi: Adv. Mater. Res., 2014, vol. 922, pp. 676–81.10.4028/www.scientific.net/AMR.922.676 ↗
15. S. Allain, J.P. Chateau, and O. Bouaziz: Mater. Sci. Eng. A, 2004, vols. 387–389, pp. 143–47.10.1016/j.msea.2004.01.060 ↗
16. K.-T. Park, K.G. Jin, S.H. Han. S.W. Hwang, K. Choil, and C.S. Lee: Mater. Sci. Eng. A, 2010, vol. 527, pp. 3651–61.10.1016/j.msea.2010.02.058 ↗
17. S. Allain, O. Bouaziz, and J.P. Chateau: Scripta Mater., 2010, vol. 62, pp. 500–03.10.1016/j.scriptamat.2009.12.026 ↗
18. S.I. Lee, S. Y. Lee, J. Han, and B. Hwang: Mater. Sci. Eng. A, 2019, vol. 742, pp. 334–43.10.1016/j.msea.2018.10.107 ↗
19. K.M. Rahman, V.A. Vorontsov, and D. Dye: Acta Mater., 2015, vol. 89, pp. 247–57.10.1016/j.actamat.2015.02.008 ↗
20. M. Koyama, T. Sawaguchi, and K. Tsuzaki: Mater. Sci. Eng. A, 2011, vol. 530, pp. 659–63.10.1016/j.msea.2011.10.038 ↗
21. I. Gutierrez-Urrutia, S. Zaefferer, and D. Raabe: Mater. Sci. Eng. A, 2010, vol. 527, pp. 3552–60.10.1016/j.msea.2010.02.041 ↗
22. S. Kang, J.G. Jung, M. Kang, W. Woo, and Y.K. Lee: Mater. Sci. Eng. A, 2016, vol. 652, pp. 212–20.10.1016/j.msea.2015.11.096 ↗
23. B.C. De Cooman, Y. Estrin, and S.K. Kim: Acta Mater., 2018, vol. 142, pp. 283–362.10.1016/j.actamat.2017.06.046 ↗
24. T. Yang, Y.L. Zhao, Y. Tong, Z.B. Jiao, J. Wei, J.X. Cai, X.D. Han, D. Chen, A. Hu, J. J. Kai, K. Lu, Y. Liu, and C.T. Liu: Science, 2018, vol. 362, pp. 933–37.10.1126/science.aas8815 ↗
25. K. Zhang, H.Y. Wen, B.B. Zhao, X.P. Dong, and L.T. Zhang: Mater. Charact., 2019, vol. 155, p. 109792.10.1016/j.matchar.2019.109792 ↗
26. C. Scott, B. Remy, J.-L. Collet, A. Cael, C. Bao, F. Danoix, B. Malard, and C. Curfs: Int. J. Mater. Res., 2011, vol. 102, pp. 538–49.10.3139/146.110508 ↗
27. H. Kubo, K. Nakamura, S. Farjami, and T. Maruyama: Mater. Sci. Eng. A, 2004, vol. 378, pp. 343–48.10.1016/j.msea.2003.10.359 ↗
28. Y. Yazawa, T. Furuhara, and T. Maki: Acta Mater., 2004, vol. 52, pp. 3727–36.10.1016/j.actamat.2004.04.027 ↗
29. K.H. Han: Mater. Sci. Eng. A, 2000, vol. 279, pp. 1–9.10.1016/S0921-5093(99)00690-5 ↗
30. S. Kajiwara, D.Z. Liu, T. Kikuchi, and N. Shinya: Scripta Mater., 2001, vol. 44, pp. 2809–14.10.1016/S1359-6462(01)00978-2 ↗
31. J. Moon, H.-Y. Ha, S.-J. Park, T.-H. Lee, J.H. Jang, C.-H. Lee, H.N. Han, and H.-U. Hong: J. Alloys Compds., 2019, vol. 775, pp. 1136–46.10.1016/j.jallcom.2018.10.253 ↗
32. Y.S. Zhang, X.M. Zhu, and S.H. Zhong: Corr. Sci., 2004, vol. 46, pp. 853–76.10.1016/j.corsci.2003.09.002 ↗
33. S.S.M. Tavares, M.L. Laurya, H.N. Farneze, R.V. Landim, J.A.C. Velasco, and J.L.M. Andia: Eng. Fail. Anal., 2019, vol. 104, pp. 331–40.10.1016/j.engfailanal.2019.05.017 ↗
34. X.M. Chen, Y.H. Wang, J.C. Xiong, G.Y. Li, Y.Z. Tian, W.Q. Cao, and T.S. Wang: Front. Mater., 2020, vol. 7.10.3389/fmats.2020.00070 ↗
35. Y.H. Wang, J.M. Kang, Y. Peng, T.S. Wang, N. Hansen, and X.X. Huang: Scripta Mater., 2018, vol. 155, pp. 41–45.10.1016/j.scriptamat.2018.06.019 ↗
36. S. Deb, S.K. Panigrahi, and M. Weiss: Mater. Charact., 2019, vol. 154, pp. 80–93.10.1016/j.matchar.2019.05.023 ↗
37. K. Maruyama, K. Sawada, and J.-I. Koike: ISIJ Int., 2001, vol. 41, pp. 641–53.10.2355/isijinternational.41.641 ↗
38. M. Roussel, X. Saurage, M. Perez, D. Magné, A. Hauet, A. Steckrneyer, M. Vermont, T. Chaise, and M. Couvrat: Materials, 2018, vol. 4, pp. 331–39.
39. S.H. Byun, N. Kang, T.H. Lee, S.K. Ahn, H.W. Lee, W.S. Chang, and K.M. Cho: Metall. Mater. Int., 2012, vol. 18, pp. 201–07.10.1007/s12540-012-2001-y ↗
40. Y.M. He, Y.H. Wang, K. Guo, and T.S. Wang: Mater. Sci. Eng. A, 2017, vol. 708, pp. 248–53.10.1016/j.msea.2017.09.103 ↗
41. K. Kaneko, T. Fukunaga, K. Yamada, N. Nakada, M. Kikuchi, Z. Saghi, J.S. Barnard, and P.A. Midgley: Scripta Mater., 2011, vol. 65, pp. 509–12.10.1016/j.scriptamat.2011.06.010 ↗
42. Y.H. Wang, B.D. Shi, Y.M. He, H.W. Zhang, Y. Peng, and T.S. Wang: Materials, 2018, vol. 11, pp. 253–61.10.3390/ma11020253 ↗
43. Y.H. Wang, J.M. Kang, Y. Peng, T.S. Wang, N. Hansen, and X.X. Huang: J. Mater. Sci. Technol., 2018, vol. 34, pp. 229–33.10.1080/02670836.2017.1368218 ↗
44. S. Curtze, V.T. Kuokkala, A. Oikari, J. Tälonen, and H. Hänninen: Acta Mater., 2011, vol. 59, pp. 1068–76.10.1016/j.actamat.2010.10.037 ↗
45. S. Allain, J.P. Chateau, O. Bouaziz, S. Migot, and N. Guelton: Mater. Sci. Eng. A, 2004, vol. 387, pp. 158–62.10.1016/j.msea.2004.01.059 ↗
46. O. Bouaziz and N. Guelton: Mater. Sci. Eng. A, 2001, vols. 319–321, pp. 246–49.10.1016/S0921-5093(00)02019-0 ↗
47. P.J. Brofman and G.S. Ansell: Metall. Mater. Trans. A, 1978, vol. 9A, pp. 879–80.10.1007/BF02649799 ↗
48. W.S. Yang and C.M. Wan: J. Mater. Sci., 1990, vol. 25, pp. 1821–23.10.1007/BF01045392 ↗
49. L. Lin, T.Y. Hsu, and Y Zu: Calphad, 1997, vol. 21, pp. 443–48.10.1016/S0364-5916(97)00044-8 ↗
50. A.S. Hamada, L.P. Karjalainen, and M.C. Somani: Mater. Sci. Eng. A, 2007, vol. 467, pp. 114–24.10.1016/j.msea.2007.02.074 ↗
51. P. Kusakin, A. Belyakov, C. Haase, R. Kaibyshev, and D.A. Molodov: Mater. Sci. Eng. A, 2014, vol. 617, pp. 52–60.10.1016/j.msea.2014.08.051 ↗
52. J.P. Chateau, A. Dumay, S. Allain, and A.J. Jacques: JPCS, 2010, vol. 240, p. 012023.
53. X. Wang, H.S. Zurob, J.D. Embury, X. Ren, and I. Yakubtsov: Mater. Sci. Eng. A, 2010, vol. 527, pp. 3785–91.10.1016/j.msea.2010.03.014 ↗
54. H. Wu, S. Huang, C.Y. Zhu, H.G. Zhu, and Z.H. Xie: Prog. Nat. Sci. Mater., 2020, vol. 30, pp. 239–45.10.1016/j.pnsc.2020.01.012 ↗
55. X.J. Wang, X.J. Sun, C. Song, H. Chen, W. Han, and F. Pana: Mater. Sci. Eng. A, 2017, vol. 698, pp. 110–16.10.1016/j.msea.2017.05.023 ↗
56. X.Z. Zhang, T.J. Chen, and Y.H. Qin: Mater. Des., 2016, vol. 99, pp. 182–92.10.1016/j.matdes.2016.03.068 ↗
57. Environmental Chemistry, J.K. Barbalace Inc., 1995, https://environmentalchemistry.com/yogi/perioc, Accessed 22 Oct 1995.
58. H.H. Zhi, C. Zhang, S. Antonov, H.Y. Yu, T. Guo, and Y.J. Su: Acta Mater., 2020, vol. 195, pp. 371–82.10.1016/j.actamat.2020.05.062 ↗
59. M. Sauzay and L.P. Kubin: Progr. Mater. Sci., 2011, vol. 56, pp. 725–84.10.1016/j.pmatsci.2011.01.006 ↗
60. N. Gao and T.N. Baker: ISIJ, 1988, vol. 38, pp. 144–51.
61. P. Kusakin, A. Belyakov, D.A. Molodov, and R. Kaibyshev: Mater. Sci. Eng. A, 2017, vol. 687, pp. 82–84.10.1016/j.msea.2017.01.080 ↗