Application of 3D DIC-Assisted Residual Stress Measurements for Friction Stir Welding Weld from Ultrafine-Grained Aluminum
Source abstract
Abstract
Abstract The present study describes a novel approach applying 3D digital image correlation to a hole drilling method to measure residual stresses. Measurements were performed on a friction stir-welded joint made of ultrafine-grained aluminum. The results show that severe plastic deformation did not significantly change the residual stresses, while in the weld’s stir zone they increased to 100 to 200 MPa. The obtained results demonstrate the reliability of the applied residual stress measurement method.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (18)
Show source-provided references
1. J. Guo, H. Fu, B. Pan, R. Kang, Chin. J. Aeronaut., 2020, doi:10.1016/j.cja.2019.10.010.10.1016/j.cja.2019.10.010 ↗
2. [2] R.S. Mishra, Z.Y. Ma, Mater. Sci. Eng. R Reports, 2005, 50, 1–78. doi:10.1016/j.mser.2005.07.001.10.1016/j.mser.2005.07.001 ↗
3. [3] R.Z. Valiev, Y. Estrin, Z. Horita, T.G. Langdon, M.J. Zehetbauer, Y. Zhu, Jom, 2006, 58 33–39. doi:10.1007/s11837-016-1820-6.10.1007/s11837-016-1820-6 ↗
4. [4] L. Olejnik, A. Rosochowski, M. Richert, Mater. Sci. Forum, 2008, 584–586, 108–113.10.4028/www.scientific.net/MSF.584-586.108 ↗
5. [5] M. Orlowska, T. Brynk, A. Huetter, J. Goliński, N. Enzinger, L. Olejnik, et al., Mater. Sci. Eng. A, 2020, 777, 139076. doi:10.1016/j.msea.2020.139076.10.1016/j.msea.2020.139076 ↗
6. [6] F.C. Liu, T.W. Nelson, Mater. Des., 2017, 115, 467–478. doi:10.1016/j.matdes.2016.11.066.10.1016/j.matdes.2016.11.066 ↗
7. [7] P.L. Threadgill, A.J. Leonard, H.R. Shercliff, P.J. Withers, Int. Mat. Rev., 2009, 54, 49–93. doi:10.1179/174328009X411136.10.1179/174328009X411136 ↗
8. A. Makino, D. Nelson, Exp. Mech., 1994, 34:66–78.10.1007/BF02328443 ↗
9. [9] T. Brynk, A.T. Krawczyńska, D. Setman, Z. Pakieła, Arch. Civ. Mech. Eng., 2020, 4, 1–12. doi:10.1007/s43452-020-00068-4.10.1007/s43452-020-00068-4 ↗
10. [10] L. Romero-Resendiz, C. Reyes-Ruiz, J.M. Cabrera, C. Braham, G. Gonzalez, Mater. Charact., 2019, 152, 44–57.10.1016/j.matchar.2019.04.007 ↗
11. H. Sanati, F. Reshadi, G. Faraji, N. Soltani, E. Zalnezhad, Proc. Inst. Mech. Eng. B 2014. doi: 10.1177/0954405414534432.10.1177/0954405414534432 ↗
12. [12] F. Nazari, M. Honarpisheh, H. Zhao, Micron, 2020, 132, 102843. doi:10.1016/j.micron.2020.102843.10.1016/j.micron.2020.102843 ↗
13. [13] T. Sun, M.J. Roy, D. Strong, P.J. Withers, P.B. Prangnell, J. Mater. Process. Tech., 2017, 242, 92–100. doi:10.1016/j.jmatprotec.2016.11.015.10.1016/j.jmatprotec.2016.11.015 ↗
14. [14] L. Buglioni, L.N. Tufaro, H.G. Svoboda, Procedia Mater. Sci., 2015, 9, 87–96. doi:10.1016/j.mspro.2015.04.011.10.1016/j.mspro.2015.04.011 ↗
15. I. Alinaghian, S. Amini, M. Honarpisheh, J. Strain Anal., 2018, doi:10.1177/0309324718789768.10.1177/0309324718789768 ↗
16. [16] I. Alinaghian, M. Honarpisheh, Int. J. Adv. Manuf. Technol., 2018, 95, 2757–2766.10.1007/s00170-017-1431-6 ↗
17. [17] L. Fratini, B. Zuccarello, Int. J. Mach. Tools Manuf., 2006, 46, 611–619. doi:10.1016/j.ijmachtools.2005.07.013.10.1016/j.ijmachtools.2005.07.013 ↗
18. [18] H. Jafari, H. Mansouri, M. Honarpisheh, J. Manuf. Process., 2019, 43, 145–153. doi:10.1016/j.jmapro.2019.05.023.10.1016/j.jmapro.2019.05.023 ↗