Effect of Alloying and Coiling Temperature on the Microstructure and Bending Performance of Ultra-High-Strength Strip Steel
Source abstract
Abstract
Two different high-strength B-containing microalloyed steel strips produced in industrial processing conditions, one treated with Ti and the other treated with Al, processed by controlled rolling, accelerated cooling, and coiling in two different temperature ranges [723 K to 733 K (450 °C to 460 °C)] and [633 K to 653 K (360 °C to 380 °C)] were subjected to bend testing. The Ti-treated steel coiled at the higher temperature 733 K (460 °C) showed the best bending performance. The relatively softer (tensile strength of < 900 MPa) and homogeneous microstructure containing mostly granular bainite and upper bainite to ~ 300-400 μm depth below the surface, generated at the higher coiling temperature, is preferred for bendability. The lower temperature coiling resulted in the formation of a hard surface layer dominated by martensite which is undesired as the steel becomes prone to shear cracking and interphase separation due to strain localization. The combined effects of beneficial texture components such as γ-fiber, {332} <113> and even {112} <131> in the sub-surface region as well as uniformity of through thickness texture of the rolled sheet improve the bendability. In the presence of crack initiators, like coarse and brittle TiN particles found in the Ti-treated steel, a harder microstructure and the presence of Cube and Goss texture in the sub-surface layer, seen for the lower coiling temperature can cause local transgranular cleavage cracking. Finally, the post-uniform elongation obtained from tensile testing and bendability follow a good correlation.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Forming Simulation Techniques · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. M. Saiji, H. Kohei, and T. Yasush: JFE Tech. Rep., 2007, vol. 10, pp. 13–18.
2. K. Yamazaki, M. Oka, H. Yasuda, Y. Mizuyama, and H. Tsuchiya: Nippon Steel Tech. Rep., 1995, vol. 64, pp. 37–44.
3. Y.B. Xu, Y.L. Bai, Q. Xue, and L.T. Shen: Acta Mater., 1996, vol. 44, pp. 1917–26.10.1016/1359-6454(95)00306-1 ↗
4. M. Kaupper and M. Merklein: CIRP Ann. Manuf. Technol., 2013, vol. 62, pp. 247–50.10.1016/j.cirp.2013.03.049 ↗
5. Z. Marciniak, J.. Duncan, and S.J. Hu: Mechanics of Sheet Metal Forming, 2nd edn., Elsevier Ltd, Amsterdam, 2002.
6. E. Tempelman, H. Hercliff, and B.N. van Eyben: Manufacturing and Design: Understanding the Principles of How Things Are Made, 1st edn., Elsevier, Amsterdam, 2014.
7. D. Rèche, J. Besson, T. Sturel, and A.F. Gourgues-Lorenzon: in Relations between microstructure and bendability on TRIP-aided steels for automotive products, 2014, pp. 135–56.
8. L. Xue: Eng. Fract. Mech., 2010, vol. 77, pp. 1275–97.10.1016/j.engfracmech.2009.12.008 ↗
9. J. Joutsenvaara: in Proceedings of the METNET Seminar 2012 in Izmir, T.R. Department, ed., Kemi-Tornio University of Applied Sciences, 2012, pp. 19–29.
10. Y. Nagataki, S. Tsuyama, and Y. Hosoya: Steel Res. Lab., 2013, vol. 99, pp. 245–53.
11. K. Hashiguchi: Elastoplasticity Theory, vol. 42, Springer, Berlin, Heidelberg, 2009.10.1007/978-3-642-00273-1 ↗
12. W. Wang, M. Li, Y. Zhao, and X. Wei: Mater. Des., 2014, vol. 56, pp. 907–13.10.1016/j.matdes.2013.12.004 ↗
13. M. Kuroda and V. Tvergaard: Eur. J. Mech. A/Solids, 2004, vol. 23, pp. 811–21.10.1016/j.euromechsol.2004.05.006 ↗
14. A.J. Kaijalainen, P. Suikkanen, L.P. Karjalainen, and J.J. Jonas: Metall. Mater. Trans. A, 2014, vol. 45A, pp. 1273–83.10.1007/s11661-013-2062-7 ↗
15. W. Wang, M. Li, Y. Zhao, and X. Wei: Mater. Des., 2014, vol. 56, pp. 907–13.10.1016/j.matdes.2013.12.004 ↗
16. M.D. M. Lie: Philos. Mag. A, 2001, vol. 81, pp. 1997–2020.10.1080/01418610010019620 ↗
17. J. R. Rice: Proceedings of the 14th International Congress on Theoretical and Applied Mechanics, North Holland Publishing Co, Amsterdam, 1976, pp. 207–20.
18. A. Maatta, A. Jarvenpaa, M. Jaskari, K. Mantyjarvi, and J.A. Karjalainen: Mater. Form. Esaform 2012, Pts 1 & 2, 2012, vol. 504–506, pp. 901–06.
19. A.J. Kaijalainen, M. Liimatainen, V. Kesti, J. Heikkala, T. Liimatainen, and D.A. Porter: Metall. Mater. Trans. A, 2016, vol. 47A, pp. 4175–88.10.1007/s11661-016-3574-8 ↗
20. D. Rèche, T. Sturel, A.F. Gourgues-Lorenzon, and J. Besson: Proc. Eur. Conf. Fract. 18, 2010, pp. 1–8.
21. A. Väisänen, K. Mäntyjärvi, and J.A. Karjalainen: Key Eng. Mater., 2009, vol. 410–411, pp. 611–20.10.4028/www.scientific.net/KEM.410-411.611 ↗
22. N. Pottore, N. Fonstein, I. Gupta, and D. Bhattacharya: AHSSS Proc, 2004, pp. 119–29.
23. G. Rosenberg, I. Sinaiová, P. Hvizdoš, and L. Juhar: Metall. Mater. Trans. A, 2015, vol. 46A, pp. 4755–71.10.1007/s11661-015-3074-2 ↗
24. K. Kawamura and K. Seto: US Patent 20,130,048,151, 2013, vol. 2, pp. 6–13.
25. A.-M. Arola, A. Kaijalainen, and V. Kesti: AIP Conference Proceedings, vol. 1769, AIP Publishing LLC, 2016, p. 200024.
26. J. Sarkar, T.R.G. Kutty, D.S. Wilkinson, J.D. Embury, and D.J. Lloyd: Mater. Sci. Eng. A, 2004, vol. 369, pp. 258–66.10.1016/j.msea.2003.11.022 ↗
27. T. Gladman: The Physical Metallurgy of Microalloyed Steels, Institute of Materials, London, 1997.
28. T. Siwecki, J. Eliasson, R. Lagneborg, and B. Hutchinson: ISIJ Int., 2010, vol. 50, pp. 760–67.10.2355/isijinternational.50.760 ↗
29. H.K.D.H. Bhadeshia: Bainite in Steels: Transformations, Microstructure and Properties, IOM Communications, London, 2001.
30. B. Hutchinson, T. Siwecki, J. Komenda, J. Hagström, R. Lagneborg, J.-E. Hedin, and M. Gladh: Ironmak. Steelmak., 2014, vol. 41, pp. 1–6.10.1179/1743281213Y.0000000118 ↗
31. J. Datsko and C.T. Yang: J. Eng. Ind., 1960, vol. 82, pp. 309–13.10.1115/1.3664236 ↗
32. S.-C. Wang and P.-W. Kao: J. Mater. Sci., 1993, vol. 28, pp. 5169–75.10.1007/BF00570058 ↗
33. F. Boratto, R. Barbosa, S. Yue, and J.J. Jonas: in THERMEC’ 88, 1988, pp. 383–90.
34. M.G. Akben, T. Chandra, P. Plassiard, and J.J. Jonas: Acta Metall., 1984, vol. 32, pp. 591–601.10.1016/0001-6160(84)90070-1 ↗
35. R.K. Ray and J.J. Jonas: Int. Mater. Rev., 1990, vol. 35, pp. 1–36.10.1179/095066090790324046 ↗
36. M.P. Butrón-Guillén, J.J. Jonas, and R.K. Ray: Acta Metall. Et Mater., 1994, vol. 42, pp. 3615–27.10.1016/0956-7151(94)90428-6 ↗
37. D.M. Tracey: Eng. Fract. Mech., 1971, vol. 3, pp. 301–15.10.1016/0013-7944(71)90040-3 ↗
38. P. D. Wu, S. R. MacEwen, D. J. Lloyd, and K. W. Neale: Mater. Sci. Eng. A, 2004, vol. 364, pp. 182–87.10.1016/j.msea.2003.08.020 ↗
39. A.J. Kaijalainen, P.P. Suikkanen, L.P. Karjalainen, and D.A. Porter: Materials Science and Engineering: A, 2016, vol. 654, pp. 151–60.10.1016/j.msea.2015.12.030 ↗