journal article·2015-11

Indentation Fracture Resistance Vs Conventional Fracture Toughness of Carbon Nanotube/Alumina Nanocomposites

Soumya Sarkar, Probal Kumar Das

Publisher page

Abstract

Multiwalled carbon nanotube (MWCNT)/alumina (Al2O3) nanocomposites were fabricated using two varieties of CNT to access the effect of morphological variation of the filler on fracture resistance (K R)/toughness (K IC) of studied specimens. Special attention was also given to compare K R and K IC values for tracing out the primary selection criterion of appropriate indentation fracture (IF) equation used in relatively faster and simpler ‘direct crack measurement’ (DCM) technique to evaluate K R values close to stringent ‘single edge notched beam’ (SENB) derived K IC data. While K IC was calculated using the unique expression suitable for specimens tested under four-point flexure, K R values were evaluated using a series of IF equations suitable for Palmqvist and/or median crack systems. As far as change in K R and/or K IC of nanocomposites was concerned, it was noticed that for longer/thicker CNTs having relatively higher internal bamboo structures, much lower amount (0.15 vol pct) was adequate to achieve the highest improvement in K R (~87 pct) or K IC (~50 pct) over pure Al2O3 (Laugier K R ≈ 3.83 MPa-m0.5; K IC ≈ 3.48 MPa-m0.5) than that required for smaller/thinner CNTs (≥0.3 vol pct). On contrary, resistance to fracture up to 1.2 vol pct CNT loading was much enhanced in specimens fabricated with smaller/thinner CNTs over those fabricated using longer/thicker CNTs. Comparatively better morphology, adequate CNT dispersion, and higher population of bridging elements in specimens containing smaller/thinner CNTs were the key factors behind such toughness retention.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced ceramic materials synthesis · Innovative concrete reinforcement materials · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. J. Sun, L. Gao and X. Jin, Ceram. Int. 2005, vol 31, pp. 893–96.10.1016/j.ceramint.2004.10.002 ↗
2. S. W. Kim, W. S. Chung, K-S Sohn, C-Y Son and S. Lee, Mater. Sci. Eng. A 2009, vol 517 pp. 293–29.10.1016/j.msea.2009.04.035 ↗
3. S. Sarkar and P. K. Das, Mater. Sci. Eng. A 2012, vol 531 pp. 61–69.10.1016/j.msea.2011.10.024 ↗
4. G-D Zhan and A. K. Mukherjee, Int. J. Appl. Ceram. Technol. 2004, vol 1, pp. 161–71.10.1111/j.1744-7402.2004.tb00166.x ↗
5. I. Ahmad, H. Cao, H. Chen, H. Zhao, A. Kennedy and Y. Q. Zhu, J. Eur. Ceram. Soc. 2010, vol 30, pp. 865–73.10.1016/j.jeurceramsoc.2009.09.032 ↗
6. J. Fan, D. Zha, M. Wu, Z. Xu and J. Song, J. Am. Ceram. Soc. 2006, vol 89 pp. 750–53.10.1111/j.1551-2916.2005.00774.x ↗
7. S. Bi, G. Hou, X. Su, Y. Zhang and F. Guo, Mater. Sci. Eng. A 2011, vol 528, pp. 1596–01.10.1016/j.msea.2010.10.076 ↗
8. K. Lee, C. B. Mo, S. B. Park and S. H. Hong, J. Am. Ceram. Soc. 2011, vol 94, pp. 3774–79.10.1111/j.1551-2916.2011.04689.x ↗
9. M. Estili, A. Kawasaki and Y. Sakka, Adv. Mater. 2012, vol 24, pp. 4322–26.10.1002/adma.201201134 ↗
10. L. Kumari, T. Zhang, G. H. Du, W. Z. Li, Q. W. Wang, A. Datye and K. H. Wu, Compos. Sci. Technol. 2008, vol 68, pp. 2178–83.10.1016/j.compscitech.2008.04.001 ↗
11. L. Kumari, T. Zhang, G. H. Du, W. Z. Li, Q. W. Wang, A. Datye and K. H. Wu, Ceram. Int. 2009, vol 35, pp. 1775–81.10.1016/j.ceramint.2008.10.005 ↗
12. S. Sarkar and P. K. Das, Rev. Adv. Mater. Sci. 2014, vol 37, pp. 53–82.
13. K. Ahmad and W. Pan, J. Eur. Ceram. Soc. 2015, vol 35, pp. 663–71.10.1016/j.jeurceramsoc.2014.08.044 ↗
14. J. Yi, W.J. Xu, Z.P. Xi, J. Chen and L. Zhu, Mater. Res. Bull. 2015, vol 64, pp. 323–26.10.1016/j.materresbull.2015.01.017 ↗
15. Estili M, Sakka Y, Kawasaki A (2013) Nanotechnol. 24:155702.10.1088/0957-4484/24/15/155702 ↗
16. Yazdani B, Xia Y, Ahmad I, Zhu Y (2015) J. Eur. Ceram. Soc. 35:179–8610.1016/j.jeurceramsoc.2014.08.043 ↗
17. I. Ahmad, B. Yazdani and Y. Zhu, Nanomaterials. 2015, vol 5, pp. 90–114.10.3390/nano5010090 ↗
18. N. Ogihara, Y. Usui, K. Aoki, M. Shimizu, N. Narita, K. Hara, K. Nakamura, N. Ishigaki, S. Takanashi, M. Okamoto, H. Kato, H. Haniu, N. Ogiwara, N. Nakayama, S. Taruta and N. Saito, Nanomedicine 2012, vol 7, pp. 981–93.10.2217/nnm.12.1 ↗
19. Z. Xia, L. Riester, W.A. Curtin, H. Li, B.W. Sheldon, J. Liang, B. Chang and J.M. Xu, Acta Mater. 2004, vol 52, pp. 931–44.10.1016/j.actamat.2003.10.050 ↗
20. Li Y, Liu S, Hu N, Han X, Zhou L, Ning H, Wu L, Alamusi L, Yamamoto G, Chang C, Hashida T, Atobe S, Fukunaga H (2013) J. Appl. Phys. 113:144304.10.1063/1.4800110 ↗
21. G. R. Anstis, P. Chantikul, B. R. Lawn and D. B. Marshall, J. Am. Ceram. Soc. 1981, vol 64, pp. 533–38.10.1111/j.1151-2916.1981.tb10320.x ↗
22. J.E. Blendell: Ph.D. Thesis, (MTI Press: Cambridge, MA, 1979).
23. A.G. Evans: in Fracture Mechanics Applied to Brittle Materials, W. Freiman, ed., ASTM STP 678: West Conshohocken, PA, 1979, pp. 112–35.10.1520/STP36630S ↗
24. A.G. Evans and T.R. Wilshaw, Acta Mater. 1976, vol 24, pp. 939–56.10.1016/0001-6160(76)90042-0 ↗
25. JIS-R-1607, In Japanese Standards Association, 1995.
26. J. Lankford, J. Mater. Sci. Lett. 1982, vol 1, pp. 493–95.10.1007/BF00721938 ↗
27. M.T. Laugier, J. Mater. Sci. Lett. 1985, vol 4, pp. 1539–41.10.1007/BF00721390 ↗
28. H.R. Lawn and E.R. Fuller, J. Mater. Sci. 1975, vol 10, pp. 2016–24.10.1007/BF00557479 ↗
29. K.M. Liang, G. Orange and G. Fantozzi, J. Mater. Sci. 1990, vol 25, pp. 207–14.10.1007/BF00544209 ↗
30. K. Niihara, R. Morena and D.P.H. Hasselman, J. Mater. Sci. Lett. 1982, vol 1, pp. 13–16.10.1007/BF00724706 ↗
31. D. Ostrovoy, N. Orlovskaya, V. Kovylyaev and S. Firstov, J. Eur. Ceram. Soc. 1998, vol 18, pp. 381–90.10.1016/S0955-2219(97)00145-3 ↗
32. C.B. Ponton and R.D. Rawlings, Brit. Ceram. Trans. J. 1989, vol 88, pp. 83–90.
33. D.K. Shetty, I.G. Wright, P.N. Mincer and H. Clauer, J. Mater. Sci. 1985, vol 20, pp. 1873–82.10.1007/BF00555296 ↗
34. S. Sarkar and P. K. Das, J. Therm. Anal. Calorim. 2012, vol 107, pp. 1093–03.10.1007/s10973-011-1797-x ↗
35. S. Sarkar and P. K. Das, Mater. Res. Bull. 2013, vol 48, pp. 41–47.10.1016/j.materresbull.2012.09.064 ↗
36. ASTM C 1421-09, (ASTM International, PA, United States: 2009).
37. W. H. Duan, Q. Wang and F. Collins, Chem. Sci. 2011, vol 2, pp. 1407–13.10.1039/c0sc00616e ↗
38. L. Jiang, L. Gao and J. Sun, J. Colloid Interf. Sci. 2003, vol 260 pp. 89–94.10.1016/S0021-9797(02)00176-5 ↗
39. J. Zhang and L. Gao, Mater. Lett. 2007, vol 61, pp. 3571–74.10.1016/j.matlet.2006.11.138 ↗
40. J. B. Wachtman, W. R. Cannon and M. J. Matthewson: Mechanical properties of ceramics. 2nd ed. (John Wiley & Sons, Inc., New York, 2009).10.1002/9780470451519 ↗
41. H. Miyazaki, H. Hyuga, K. Hirao and T. Ohji, J. Eur. Ceram. Soc. 2007, vol 27, pp. 2347–54.10.1016/j.jeurceramsoc.2006.09.002 ↗
42. F. Sergejev and M. Antonov, Proc. Estonian Acad. Sci. Eng. 2006, vol 12, pp. 388–98.10.3176/eng.2006.4.07 ↗
43. A. Shigenori, N. Hirohisa, H. Yoshiaki, T. Yasuyuki and K. Shigeki, J. Jpn. Prosthodont. Soc. 2008, vol 52, pp. 49–58.10.2186/jjps.52.49 ↗
44. R. Spiegler, S. Schmadder and L. S. Sigl, J. Hard Mater. 1990, vol 1, pp. 147–58.
45. M. Szutkowska and M. Boniecki, J. Optoelectron. Adv. M. 2010, vol 12, pp. 301–08.
46. R. I. Todd and B. Derby, Acta Mater. 2004, vol 52, pp. 1621–29.10.1016/j.actamat.2003.12.007 ↗