journal article·2016-06

Observation of Etch-Pits and LAGB Configurations During Ambient Creep of Ti-6Al-4V Alloy

Jalaj Kumar, A. K. Singh, S. Ganesh Sundara Raman, Vikas Kumar

Publisher page

Abstract

The present work describes the microstructural features of alloy Ti-6Al-4V during constant stress creep at ambient temperature. Samples tested at 800 and 900 MPa stress levels exhibit the presence of etch-pits and/or voids. The ambient creep strain increases with an increase in applied stress due to higher strain rate sensitivity at higher stresses. A high density of low-angle grain boundaries is noticed in and around etch-pits in the creep-tested specimens due to occurrence of slip. The inverse pole figure obtained by EBSD indicates prismatic texture as the main deformation component in the creep-tested specimens.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · High Temperature Alloys and Creep · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. B.W. Neuberger, C. Greene, G. Gute (2002) Mat. Res. Soc. Symp. Proc., 716: 71-78.
2. Air Force Technology F-35 Lightning II: © Lockheed Martin Aeronautics Company. http://www.airforcetechnology.com/projects/jsf/, 2011.
3. 3.M.Geetha, A. K. Singh, R. Asokamani, A. K. Gogia : Prog. Mater. Sci, 2009, vol. 54(3), pp. 397-425.10.1016/j.pmatsci.2008.06.004 ↗
4. T. Yamada, K. Kawabata, E. Sato, K.Kuribayashi,I.Jimbo: Mat. Sci. Engg. A, 2004,vol.387-389, pp. 719-722.10.1016/j.msea.2004.01.146 ↗
5. 5.D. Doraiswamy and S. Ankem: Acta Mater., 2003, vol. 51(6), pp. 1607-1619.10.1016/S1359-6454(02)00561-X ↗
6. 6.A. Jaworski and S. Ankem: Metall. Mater. Trans. A, 2006, vol. 37A(9), pp. 2755-2765.10.1007/BF02586108 ↗
7. 7.A. K. Aiyangar, B.W. Neuberger, P. G. Oberson, and S. Ankem: Metall. Mater. Trans. A 2005, vol. 36A(3), pp. 637-644.10.1007/s11661-005-0179-z ↗
8. P.G. Obersonand S. Ankem: Int.J.Plast., 2009,vol.25(5), pp. 881-900.10.1016/j.ijplas.2008.06.002 ↗
9. Tetsuya Matsunaga, Tatsuya Kameyama, Kohei Takahashi and Eiichi Sato: Mat.Trans., 2009, vol. 50 (12), pp. 2858- 2864.10.2320/matertrans.M2009223 ↗
10. Hisamune Tanaka, Tomoyasu Yamada, Eiichi Sato, ItaruJimbo: Scripta Mat., 2006,vol. 54,pp.121–124.10.1016/j.scriptamat.2005.08.045 ↗
11. T. Neeraj, M.J. Mills: Mat. Sci. Engg. A,2001, vol.319–321, pp. 415–419.10.1016/S0921-5093(01)01045-0 ↗
12. T.Neeraj, D.H. Hou, G.S. Daehn, M.J.Wills: ActaMater.,2000, vol. 48, pp.1225-1238.10.1016/S1359-6454(99)00426-7 ↗
13. S.Suri, T. Neeraj, G.S. Daehn, D.-H. Hou, J.M. Scott, R.W.Hayes, M.J. Mills: Mat. Sci. Engg. A, 1997,vol.234-236,pp.996-999.10.1016/S0921-5093(97)00322-5 ↗
14. Ben C. Odegard, Anthony W. Thompson: Met. Trans., 1974,vol.5,pp.1207-1213.10.1007/BF02644335 ↗
15. W.H. Reimann: J. Mat., JMLSA,1971, vol. 6 (4), pp. 926-940.
16. G. Malkondaiah, N. Prasad, G. Sundararajan, P. Rama Rao: Acta. Metall, 1988, vol.36 (8) pp. 2167-2181.10.1016/0001-6160(88)90318-5 ↗
17. S.Gollapudi, D.V.V. Satyanarayana, C. Phaniraj, T.K. Nandy: Mat. Sci. Engg. A, 2012,vol.556, pp. 510-18.10.1016/j.msea.2012.07.020 ↗
18. D.A.P. Reis, C.R.M. Silva, M.C.A. Nono, M.J.R. Barboza, F. PiorinoNeto, E.A.C. Perez: Mat. Sci. Engg. A,2005, vol.399,pp. 276–280.10.1016/j.msea.2005.03.073 ↗
19. 19.M.J.R. Barboza, C. Moura Neto, C.R.M. Silva: Mater. Sci. Eng. A, 2004, vol. 369, pp. 201–209.10.1016/j.msea.2003.11.016 ↗
20. V. Sinha, J.E. Spowart, M.J. Mills, J.C. Williams: Met. Trans. A, 2006,vol.37A, pp. 1507-1518.10.1007/s11661-006-0095-x ↗
21. F. Bridier, P. Villechaise, J. Mendez: Acta Mat., 2008,vol.56, pp. 3951-3962.10.1016/j.actamat.2008.04.036 ↗
22. Jalaj Kumar, Vajinder Singh, ParthaGhosal,Vikas Kumar: Mat. Sci. Engg. A, 2015,vol.623, pp. 49–58.10.1016/j.msea.2014.11.021 ↗
23. B.S. Katelun: M.Sc. Dissertation, Ohio State University, 2010.
24. S. Naka and A. Lasalmonie: Mat. Sci. Engg. A, 1982, vol.56, pp. 19-24.10.1016/0025-5416(82)90178-1 ↗