journal article·2015-05

Optimizing the Compressive Strength of Strain-Hardenable Stretch-Formed Microtruss Architectures

Bosco Yu, Khaled Abu Samk, Glenn D. Hibbard

Publisher page

Abstract

The mechanical performance of stretch-formed microtrusses is determined by both the internal strut architecture and the accumulated plastic strain during fabrication. The current study addresses the question of optimization, by taking into consideration the interdependency between fabrication path, material properties and architecture. Low carbon steel (AISI1006) and aluminum (AA3003) material systems were investigated experimentally, with good agreement between measured values and the analytical model. The compressive performance of the microtrusses was then optimized on a minimum weight basis under design constraints such as fixed starting sheet thickness and final microtruss height by satisfying the Karush–Kuhn–Tucker condition. The optimization results were summarized as carpet plots in order to meaningfully visualize the interdependency between architecture, microstructural state, and mechanical performance, enabling material and processing path selection.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Cellular and Composite Structures · Metal Forming Simulation Techniques · Advanced Materials and Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (54)

Show source-provided references
1. M.F. Ashby: Phil Trans R Soc A, 2006; vol. 364, pp. 15-30.10.1098/rsta.2005.1678 ↗
2. V.S. Deshpande, N.A. Fleck, M.F. Ashby: J Mech Phys Solids, 2001; vol. 49, pp. 1747-1769.10.1016/S0022-5096(01)00010-2 ↗
3. V.S. Deshpande, M.F. Ashby, N.A. Fleck: Acta Mater, 2001; vol. 49, pp. 1035-1040.10.1016/S1359-6454(00)00379-7 ↗
4. E. Bele, B.A. Bouwhuis, G.D. Hibbard: Mat Sci Eng A-Struct, 2008; vol. 489, pp. 29-37.10.1016/j.msea.2008.01.081 ↗
5. S. Chiras, D.R. Mumm, A.G. Evans, N. Wicks, J.W. Hutchinson, K. Dharmasena, H.N.G. Wadley, S. Fichter: Int J Solids Struct, 2002; vol. 39, pp. 4093-4115.10.1016/S0020-7683(02)00241-X ↗
6. N. Wicks, J.W. Hutchinson: Mech Mater, 2004; vol. 36, pp. 739-751.10.1016/j.mechmat.2003.05.003 ↗
7. A.J. Jacobsen, W. Barvosa-Carter, S. Nutt: Acta Mater, 2007; vol. 55, pp. 6724-6733.10.1016/j.actamat.2007.08.036 ↗
8. B.A. Bouwhuis, T. Ronis, J.L. McCrea, G. Palumbo, G.D. Hibbard: Comp Sci Tech, 2009; vol. 69, pp. 385-390.10.1016/j.compscitech.2008.10.022 ↗
9. E. Bele, B.A Bouwhuis, G.D. Hibbard: Acta Mater, 2009; vol. 57, pp. 5927-5935.10.1016/j.actamat.2009.08.017 ↗
10. D.D. Radford, N.A. Fleck, V.S. Deshpande: Int J Impact Eng, 2006; vol. 32, pp. 968-987.10.1016/j.ijimpeng.2004.08.007 ↗
11. K.P. Dharmasena, D.T. Queheillalt, H.N.G. Wadley, P. Dudt, Y. Chen, D. Knight, A.G. Evans, V.S. Deshpande: Eur J Mech A/Solids, 2010; vol. 29, pp. 56-67.10.1016/j.euromechsol.2009.05.003 ↗
12. C.J. Yungwirth, J. O’Connor, A. Zakraysek, V.S. Deshpande, H.N.G. Wadley: J Am Ceram Soc, 2011; vol. 94, pp. s62-s75.10.1111/j.1551-2916.2011.04501.x ↗
13. K.P. Dharmasena, H.N.G. Wadley, K. Williams, Z.Y. Xue, J.W. Hutchinson: Int J Impact Eng, 2011; vol. 38, pp. 275-289.10.1016/j.ijimpeng.2010.10.002 ↗
14. A.G. Evans, J.W. Hutchinson, N.A. Fleck, M.F. Ashby, H.N.G. Wadley: Prog Mater Sci, 2001; vol. 46, pp. 309-327.10.1016/S0079-6425(00)00016-5 ↗
15. S. Gu, T.J. Lu, A.G. Evans: Int J Heat Mass Tran, 2001; vol. 44, pp. 2163-2175.10.1016/S0017-9310(00)00234-9 ↗
16. D.T. Queheillalt, H.N.G. Wadley: Acta Mater, 2005; vol. 53, pp. 303-313.10.1016/j.actamat.2004.09.024 ↗
17. D.T. Queheillalt, H.N.G. Wadley: Mater Sci Eng A, 2005; vol. 397, pp. 132-137.10.1016/j.msea.2005.02.048 ↗
18. S.M. Pingle, N.A. Fleck, V.S. Deshpande, H.N.G. Wadley: Proc Roy Soc A-Math Phy, 2011; vol. 467, pp. 985-1011.10.1098/rspa.2010.0329 ↗
19. S.M. Pingle, N.A. Fleck, V.S. Deshpande, H.N.G. Wadley: Int J Solids Struct, 2011; vol. 48, pp. 3417-3430.10.1016/j.ijsolstr.2011.08.004 ↗
20. T.A. Schaedler, A.J. Jacobsen, A. Torrents, A.E. Sorensen, J. Lian, J.R. Greer, L. Valdevit, W.B. Carter: Science, 2011; vol. 334, pp. 962-965.10.1126/science.1211649 ↗
21. L.M. Gordon, B.A. Bouwhuis, M. Suralvo, J.L. McCrea, G. Palumbo, G.D. Hibbard: Acta Mater, 2009; vol. 57, pp. 932-939.10.1016/j.actamat.2008.10.038 ↗
22. K. AbuSamk, B. Yu, G.D. Hibbard: Comp Part A, 2012; vol. 43, pp. 955-961.10.1016/j.compositesa.2012.01.014 ↗
23. J.E. Campbell, M. Suralvo, G.D. Hibbard, H.E. Naguib: J Comp Mater, 2012; vol. 46, pp. 63-70.10.1177/0021998311410471 ↗
24. R.S. Farr: Phys Rev E, 2007; vol. 76, pp. 056608(7).
25. R.S. Farr, Y. Mao: Epl J, 2008; vol. 84, pp. 14001(6).
26. D. Rayneau-Kirkhope, Y. Mao, R. Farr: Phys Rev Letters, 2012; vol. 109, pp. 204301(4).10.1103/PhysRevLett.109.204301 ↗
27. D. Rayneau-Kirkhope, Y. Mao, R. Farr, J. Segal: Mech Res Comm, 2012; vol. 46, pp. 41-46.10.1016/j.mechrescom.2012.06.011 ↗
28. H.J. Frost, M.F. Ashby: Deformation-mechanism maps: the plasticity and creep of metals and ceramics, Oxford: Pergamon Press, 1982.
29. N. Wicks, J.W. Hutchinson: Int J Solids Struct, 2001; vol. 38, pp. 5165-5183.10.1016/S0020-7683(00)00315-2 ↗
30. H.N.G. Wadley, N.A. Fleck, A.G. Evans: Comp Sci Tech, 2003; vol. 63, pp. 2331-2343.10.1016/S0266-3538(03)00266-5 ↗
31. B.A. Bouwhuis, S.K. Tang, G.D. Hibbard: Comp Part A-Appl S, 2008; vol. 39, pp. 1556-1564.10.1016/j.compositesa.2008.06.001 ↗
32. D.J. Sypeck, H.N.G. Wadley: Adv Eng Mater, 2002; vol. 4, pp. 759-764.10.1002/1527-2648(20021014)4:10<759::AID-ADEM759>3.0.CO;2-A ↗
33. F.R. Shanley: J Aeronaut Sci, 1947; vol. 14, pp. 261-267.10.2514/8.1346 ↗
34. F.R. Shanley: Strength of Materials, McGraw-Hill, New York, 1957.
35. V.S. Deshpande, N.A. Fleck: Int J Solids Struct, 2001; vol. 38, pp. 6275-6305.10.1016/S0020-7683(01)00103-2 ↗
36. C.A. Steeves, N.A. Fleck: Int J Mech Sci, 2004; vol. 46, pp. 561-583.10.1016/j.ijmecsci.2004.04.003 ↗
37. C.A. Steeves, N.A. Fleck: Scripta Mater, 2004; vol. 50, pp. 1335-1339.10.1016/j.scriptamat.2004.02.015 ↗
38. H.W. Kuhn and A.W. Tucker: Proc. Berkeley Symp. Math. Stat. Prob., University of California Press. Berkeley, 1951, pp. 481–492.10.1525/9780520411586-036 ↗
39. W. Karush: M.Sc. Dissertation, University of Chicago, Chicago, IL, 1939.
40. P.Y. Papalambros, D.J: Wilde. Principles of Optimal Design: Modeling and Computation. 2nd ed., Cambridge University Press, New York, 2000.10.1017/CBO9780511626418 ↗
41. J. Wang, A.G. Evans, K. Dharmasena, H.N.G. Wadley: Int J Solids Struct, 2003; vol. 40, pp. 6981-6988.10.1016/S0020-7683(03)00349-4 ↗
42. W. Ramberg, W.R. Osgood: “Description of Stress–Strain Curves by Three Parameters”, The National Advisory Committee for Aeronautics (NACA) Technical Notes, 1943: No. 902.
43. B.A. Bouwhuis, G.D. Hibbard: Metall Mater Trans A, 2008; vol. 39A, pp. 3027-3033.10.1007/s11661-008-9661-8 ↗
44. ASM Hanbook: Volume 14A Metalworking: Bulk Forming, Materials Park, OH, ASM International, 2005.
45. ASM Hanbook: Volume 14B Metalworking: Sheet Forming, Materials Park, OH, ASM International, 2006.
46. D. Raabe, M. Sachtleber, H. Weiland, G. Scheele, Z.S. Zhao: Acta Mater, 2003; vol. 51, pp. 1539-1560.10.1016/S1359-6454(02)00557-8 ↗
47. G.E. Dieter: Mechanical Metallurgy. New York: McGraw-Hill, 1961.10.5962/bhl.title.35895 ↗
48. B.A. Bouwhuis, G.D. Hibbard: Metall Mater Trans B, 2006; vol. 37, pp. 919-927.10.1007/BF02735014 ↗
49. L.M. Brown: Scripta Metall, 1977; vol. 11, pp. 127-131.10.1016/0036-9748(77)90291-5 ↗
50. K. Differt, U. Essmann, H. Mughrabi: Philos Mag A, 1986; vol. 54, pp. 237-258.10.1080/01418618608242897 ↗
51. T. Hasegawa, T. Yakou: Scripta Mater, 1980; vol. 14, pp. 1083-1087.10.1016/0036-9748(80)90210-0 ↗
52. J. Grabowski: Archiwum Inzynierii Ladowej, 1986; vol. 32, pp. 401-419.
53. B. Scholtes, O. Voehringer, E. Macherauch: Mater Forum, 1987; vol. 10, pp. 54-57.
54. F.J. Humphreys, M. Hatherly: Recrystallization and Related Annealing Phenomena, Elsevier, Oxford 2004.