Microstructure Evolution of a Simulated Coarse-Grained Heat-Affected Zone of T23 Steel During Aging
Source abstract
Abstract
In this work, simulated CGHAZ of T23 steel was produced via a thermomechanical simulator, and then the CGHAZ specimens were aged at 650 °C for 0 to 240 hours to simulate the microstructure evolution of as-welded CGHAZ during service. Microstructure change and carbide precipitation were observed by OM, SEM, EBSD and TEM + EDS. Carbide precipitation kinetics in T23 steel at 650 °C was calculated for comparison with the experiment results. The hardness change of CGHAZ during aging was detected, and the effect of microstructure evolution on hardness was analyzed. The results showed that the CGHAZ of T23 steel exhibited a mixed microstructure of martensite and bainite with high hardness in as-welded condition. After aging at 650 °C, the microstructure recovered, recrystallization occurred, the dislocation density decreased, and the lath width increased. Consequently, the hardness dropped, the drop depending on the aging time. In the early stage of aging (before 24 hours), the precipitations inside the grain were mainly M3C, M7C3 and a small number of M23C6 carbides, while the precipitation at the grain boundaries was M23C6. The precipitation of M23C6 caused the hardness to drop rapidly. When aged for 24 to 48 hours, MX precipitated inside grains extensively. The precipitation hardening produced by MX could slow down the decline of hardness. As the aging proceeded, carbide precipitated and transformed as follows: M3C → M3C + M7C3 + M23C6 → M3C + M7C3 + M23C6 + MX → M23C6 + MX + M6C. W-rich carbides precipitated in some grain boundaries of CGHAZ during aging, which may be related to the W segregation at those grain boundaries.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. F. Masuyama, T. Yokoyama, Y. Sawaragi, and A. Iseda: Materials for Advanced Power Engineering (Part 1), Kluwer, New York, 1994, pp. 173–81.10.1007/978-94-011-1048-8_10 ↗
2. K. Miyata, Y. Sawaragi: ISIJ Int., 2001, vol. 41, pp. 281-289.10.2355/isijinternational.41.281 ↗
3. [3] K. Miyata, M. Igarashi, Y. Sawaragi: ISIJ Int., 1999, vol. 39, pp 947-954.10.2355/isijinternational.39.947 ↗
4. J. Arndt, K. Haarmann, G. Kottmann, J.C. Vaillant, W. Bendick, K. Kubla, A. Arbab, F. Deshayes. The T23/T24 Book, V&M, Düsseldorf, 2000.
5. [5] M. Igarashi, M. Yoshizawa, H. Matsuo, O. Miyahara, A. Iseda: Mat. Sci. Eng. A-Struct., 2009, vol. 510, pp. 104-109.10.1016/j.msea.2008.05.054 ↗
6. W. Bendick, J. Gabrel, B. Hahn, B. Vandenberghe: Int. J. Pres. Ves. Pip., 2007, vol. 84, pp. 13-20.10.1016/j.ijpvp.2006.09.002 ↗
7. X.W. Ji, P. Duan, and J. Li: Symposium on Sinicization of New Type steels for 600 MW/1000 MW Ultra-Supercritical Units, Yangzhou, 2009.
8. H. Zhao, R. Ling, J. Jia, J. Zhao: Proceedings of the CSEE, 2011, vol. 31, pp. 107-113.
9. X. Wang, D. Zhu, L. Hu, X.Q. Li, C. Yang, Z.X. Ge, Q.X. Yang: Proceedings of the CSEE, 2015, vol. 35, pp. 154-161.
10. H.G. Long, Y. Long, H.D. Chen: Electric Power, 2011, vol. 44, pp. 70-73.
11. Y.B. Ren, W. Wang, S.B. Ping: Heat Treatment of Metals, 2016, vol. 41, pp. 199-203.
12. Y. Li, X. Wang, J. Wang, A. Chen: J. Mater. Process. Tech., 2019, vol. 266, pp. 73-81.10.1016/j.jmatprotec.2018.10.028 ↗
13. J.G. Nawrocki, J.N. Dupont, C.V. Robino, J.D. Puskar, A.R. Marder: Weld. J., 2003, vol. 82, pp. 25s-35s.
14. P. Mohyla, V. Foldyna: Mat. Sci. Eng. A-Struct., 2009, vol. 510–511, pp. 234-237.10.1016/j.msea.2008.05.056 ↗
15. A. Zieliński, G. Golański, M. Sroka, P. Skupień: Mater. High Temp., 2016, vol. 33, pp. 154-163.10.1080/09603409.2016.1139306 ↗
16. [16] Y. Deng, L. Zhu, Q. Wang, F. Zou: Steel Res. Int., 2006, vol. 77, pp. 844-848.10.1002/srin.200606470 ↗
17. [17] P. Tao, C. Zhang, Z.G. Yang, H. Takeda: Acta. Metall. Sin., 2009, vol. 45, pp. 51-57.
18. J.G. Nawrocki, J.N. DuPont, A.R. Marder, C.V. Robino: Metall. Mater. Trans. A, 2001, vol. 32, pp. 2585-2594.10.1007/s11661-001-0048-3 ↗
19. N. Komai, F. Masuyama, M. Igarashi: J. Press. Ves. Tech., 2005, vol. 127, pp. 190-196.10.1115/1.1904052 ↗
20. Q.J. Wang, F.M. Zhou, Y.Q. Deng, L.H. Zhu: Baosteel Technology, 2006, vol. 24, pp. 18-22.
21. A. Fedoseeva, N. Dudova, U. Glatzel, R. Kaibyshev: J. Mater. Sci., 2016, vol. 51, pp. 9424-9439.10.1007/s10853-016-0188-x ↗
22. D.Y. Lee, E.V. Barrera, J.P. Stark, H.L. Marcus: Metall. Trans. A, 1984, vol. 15, pp. 1415-1430.10.1007/BF02648571 ↗
23. N. Gope, A. Chatterjee, T. Mukherjee, D.S. Sarma: Metall. Trans. A, 1993, vol. 24, pp. 315-326.10.1007/BF02657318 ↗
24. M.C. Tsai, C.S. Chiou, J.R. Yang: J. Mater. Sci., 2003, vol. 38, pp. 2373-2391.10.1023/A:1023940732136 ↗
25. Y. Zhang, L. Miao, X. Wang, H. Zhang, J. Li: Mater. Trans., 2009, vol. 50, pp. 2507-2511.10.2320/matertrans.ME200801 ↗
26. A. Aghajani, C. Somsen, J. Pesicka, W. Bendick, B. Hahn, G. Eggeler: Mat. Sci. Eng. A-Struct., 2009, vol. 510, pp. 130-135.10.1016/j.msea.2008.08.049 ↗
27. A. Zieliński, G. Golański, M. Sroka: Mat. Sci. Eng. A-Struct., 2017, vol. 682, pp. 664-672.10.1016/j.msea.2016.11.087 ↗
28. J. Dobrzański, A. Hernas: J. Mater. Process. Tech., 1995, vol. 53, pp. 101-108.10.1016/0924-0136(95)01966-I ↗
29. A. Kroupa, A. Výrostková, M. Svoboda, J. Janovec: Acta. Mater., 1998, vol. 46, pp. 39-49.10.1016/S1359-6454(97)00239-5 ↗
30. G. Golański: Journal of Pressure Vessel Technology, 2010, vol. 132, pp. 645031-645035.10.1115/1.4001922 ↗
31. X. Wang, X. Li, C. Yang, Z. Ge, X. Yang, Y. Ren: Journal of Chines Society of Power Engnieering, 2015, vol. 35, pp. 325-330.
32. A. Dhooge, R.E. Dolby, J. Sebille, R. Steinmetz, A.G. Vinckier: Int. J. Pres. Ves. Pip., 1978, vol. 6, pp. 329-409.10.1016/0308-0161(78)90023-6 ↗