journal article·2003-02

Improvement in fracture toughness of Ti-4.5Al-3V-2Mo-2Fe through microstructural optimization

Gunawarman, Mitsuo Ninomi, Daniel Eylon, Shiro Fujishiro, Chiaki Ouchi, Toshihiko Kazino

Publisher page

Abstract

In order to improve the observed low fracture toughness of β-rich α+β-type Ti-4.5Al-3V-2Mo-2Fe annealed at the temperature of 1123 K, a two-step cooling (TSC) after solution treatment at that temperature was proposed instead of air cooling. Solution treatment plus aging (STA) and slow furnace-cooling (SFC) treatments were also carried out on the same alloy for comparison. It was found that the relatively higher fracture toughness (J IC ) is obtained by the TSC treatment, that is, by slow cooling the alloy at a cooling rate of 0.075 Ks−1 from a temperature of 1123 to 723 K and, subsequently, water quenching to room temperature. The J IC of the two-step-cooled alloy has the same value as that of the alloy annealed at 993 K after having first been annealed at 1123 K (duplex annealing (DA)), which has been previously observed to have high fracture toughness. The J IC value can also be improved by STA, but it is still lower than that of two-step-cooled alloy. The relatively lower J IC is obtained in slow-furnace-cooled alloys. The J IC of slow-furnace-cooled alloys decreases monotonously with decreasing cooling rate for cooling rates less than 0.075 Ks−1. It is suggested that the factors responsible for increasing J IC> in two-step-cooled and solution treated-and-aged alloys are the plate-like α and secondary α, respectively, which appears in the β phase during cooling and aging, respectively. The presence of such kinds of transformation products increases the crackdeflection effect and, thus, increases fracture toughness.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Intermetallics and Advanced Alloy Properties · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. Weiss and S.L. Semiatin: Mater. Sci. Eng. A, 1999, vol. A263, pp. 243–56.10.1016/S0921-5093(98)01155-1 ↗
2. R.R. Boyer: Mater. Sci. Eng. A, 1996, vol. A213, pp. 103–14.10.1016/0921-5093(96)10233-1 ↗
3. M. Niinomi: Mater. Sci. Eng. A, 1998, vol. A243, pp. 231–36.10.1016/S0921-5093(97)00806-X ↗
4. C. Ouchi: in Metallurgy and Technology of Practical Titanium Alloys, S. Fujishiro, D. Eylon, and T. Kishi, eds., TMS, Warendale, PA, 1994, pp. 37–44.
5. F.H. Froes, H.L. Gegel, C.H. Hamilton, G.W. Kuhlman, and J.H. Moll: Titanium ’92 Science and Technology, F.H. Froes and I.L. Caplan, eds., TMS, Warrendale, PA, vol. 2, 1993, pp. 3–14.
6. M. Ishikawa, O. Kuboyama, M. Niikura, and C. Ouchi: Titanium ’92 Science and Technology, F.H. Froes and I.L. Caplan, eds., TMS, Warrendale, PA, 1993, vol. 2, pp. 141–48.
7. T. Fujita, M. Ishikawa, S. Hashimoto, K. Minakawa, and C. Ouchi: Beta Titanium Alloy in the 1990s, D. Eylon, R.R. Boyer, and D.A. Koss, eds., TMS, Warrendale, PA, 1993, pp. 61–71.
8. A. Ogawa, M. Niikura, C. Oichi, K. Minakawa, and M. Yamada: J. Testing Evaluation, 1996, vol. 24, pp. 100–09.10.1520/JTE12683J ↗
9. NKK news release, http://www.nkk.co.jp/en/release/41-03/art04.html, Apr. 2001.
10. A. Ogawa, K. Minakawa, and S. Takagi: Titanium ’95 Science and Technology, P.A. Blenkinshop, W.J. Evans, and H.M. Flower, eds., The Institute of Materials, London, 1996, vol. 2, pp. 1251–58.
11. Gunawarman, M. Niinomi, K. Fukunaga, D. Eylon, S. Fujishiro, and C. Ouchi: Mater. Sci. Eng. A, 2001, vol. A308, pp. 216–24.10.1016/S0921-5093(00)01986-9 ↗
12. Gunawarman, M. Niinomi, K. Fukunaga, D. Eylon, S. Fujishiro, and C. Ouchi: Mater. Trans., 2001, vol. 42, pp. 1339–48.10.2320/matertrans.42.1339 ↗
13. Gunawarman, M. Niinomi, K. Fukunaga, D. Eylon, S. Fujishiro, and C. Ouchi: Int. J. Mater. Product Tech., Special Issue, SPM1, 2001, vol. 2, pp. 775–80.
14. R.D. Briggs: Advances in the Science and Technology of Titanium Alloy Processing, I. Weiss, R. Srinivasan, P.J. Bania, D. Eylon, and S.L. Semiatin, eds., TMS, Warrendale, PA, 1997, pp. 413–20.
15. R.K. Bird, T.A. Wallace, and W.D. Brewer: in Advances in the Science and Technology of Titanium Alloy Processing, I. Weiss, R. Srinivasan, P.J. Bania, D. Eylon, and S.L. Semiatin, eds., TMS, Warrendale, PA, 1997, pp. 473–79.
16. Materials Properties Handbook: Titanium Alloys, R. Boyer, G. Welsch and E.W. Collings, eds., ASM INTERNATIONAL, Materials Park, OH, 1994.
17. ASTM Designation E813–89: Standard Test Method for J IC, ASTM, Philadelphia, PA, 1996, pp. 633–47.
18. Gunawarman, M. Niinomi, K. Fukunaga, D. Eylon, S. Fujishiro, and C. Ouchi: LiMAT 2001, N.J. Kim, C.S. Lee, and D. Eylon, eds., Center for Advanced Aerospace Materials, POSTECH, Pohang, Korea, 2001, vol. 1, pp. 127–32.
19. Gunawarman, M. Niinomi, D. Eylon, S. Fujishiro, and C. Ouchi: Iron Steel Inst. Jpn. Int., 2000, vol. 42 (2), pp. 191–99.10.2355/isijinternational.42.191 ↗
20. R. Davis, H.M. Flower, and D.R.F. West: J. Mater. Sci., 1979, vol. 14, pp. 712–22.10.1007/BF00772735 ↗