journal article·2015-11

The Tensile Mechanical Properties of Thermomechanically Consolidated Titanium at Different Strain Rates

Cun Liang, Mingxing Ma, Mingtu Jia, Stiliana Raynova, Jianqiang Yan, Deliang Zhang

Publisher page

Abstract

The microstructures, tensile mechanical properties, and fracture behavior of a commercially pure (CP) titanium disk (called PF/Ti disk) and a CP titanium bar (called PE/Ti bar) made by powder compact forging (PCF) and powder compact extrusion (PCE) respectively have been studied. With increasing the strain rate from 10−4 to 10−1 s−1, the yield strength of the PF/Ti disk and PE/Ti bar increased from 708 to 811 MPa and from 672 to 764 MPa, respectively; their UTS increased from 824 to 1009 MPa and from 809 to 926 MPa, respectively, and their elongation to fracture decreased from 21 to 8 pct and from 25 to 17.8 pct, respectively. With a low strain rate of 10−4 s−1, the PF/Ti disk did not show any cavities at unbonded or weakly bonded interparticle boundaries, but the PE/Ti bar showed a small number of cavities with sizes of around 1 μm. With a high strain rate of 10−2 s−1, the PF/Ti disk showed a small number of cavities with sizes in the range of 0.1 to 0.5 μm, while for the PE/Ti bar, the cavities grew into microcracks of up to 20 μm long. The findings suggest that close to 100 pct of consolidation is rapidly achieved by PCF at 1573 K (1300 °C) and PCE at 1523 K (1250 °C), respectively, possibly due to the dissolution of the particle oxide surface films during heating and rapid diffusion bonding between the fresh particle surfaces during PCF and PCE.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Metallurgy and Material Forming · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. P.G. Esteban, L. Bolzoni, E.M. Ruiz-Navas, and E. Gordo: Rev. Metal., 2011, vol. 47, pp.169-88.10.3989/revmetalmadrid.0943 ↗
2. Q. Ma: Int. J. Powder Metall., 2010, vol. 46, pp.29-44.
3. F.H. Froes, S.J. Mashl, V.S. Moxson, J.C. Hebeisen, and V.A. Duz: JOM, 2004, vol. 56, pp. 46-48.10.1007/s11837-004-0252-x ↗
4. F.H. Froes, M.N. Gungor, and M.A. Imam: JOM, 2007, vol. 59, pp. 28-31.10.1007/s11837-007-0074-8 ↗
5. H. Wang, M. Lefler, Z.Z. Fang, T. Lei, S. Fang, J. Zhang, and Q. Zhao: Key Eng. Mater., 2010, vol. 436, pp.157-63.10.4028/www.scientific.net/KEM.436.157 ↗
6. G. Abakumov, V. Duz, O. Ivasishirr, V. Moxson, and D. Savvakin: Ti 2011 - Proceedings of the 12th World Conference on Titanium. 2011. vol. 2, pp. 1639–43.
7. L. Bolzoni, E.M. Ruiz-Navas, and E. Gordo: Mater. Des., 2014, vol. 60, pp.226-32.10.1016/j.matdes.2014.04.005 ↗
8. B.B. Panigrahi, M.M. Godkhindi, K. Das, P.G. Mukunda, and P. Ramakrishnan: Mater. Sci. Eng. A, 2005, vol. 396, pp. 255-62.10.1016/j.msea.2005.01.016 ↗
9. B.B. Panigrahi: Mater. Lett., 2007, vol. 61, pp. 152-55.10.1016/j.matlet.2006.04.025 ↗
10. R.J. Low, I.M. Robertson, and G.B. Schaffer: Scripta Mater., 2007, vol. 56, pp. 895-98.10.1016/j.scriptamat.2007.01.040 ↗
11. D.F. Khan, H. Yin, H. Li, X. Qu, M. Khan, S. Ali, and M.Z. Iqbal: Mater. Des., 2013, vol. 50, pp. 479-83.10.1016/j.matdes.2013.03.003 ↗
12. D.P. Delo, and H.R. Piehler: Acta Mater., 1999, vol. 47, pp. 2841-52.10.1016/S1359-6454(99)00132-9 ↗
13. Z.L. Zhao, H.Z. Guo, Z.K. Yao, Z.F. Shi, X.N. Peng, and C. Qin: J. Mater. Process. Tech., 2012, vol. 212, pp. 1495-500.10.1016/j.jmatprotec.2012.02.011 ↗
14. V.N. Nadakuduru, D.L. Zhang, S. Raynova, P. Cao, and B. Gabbitas: Adv. Mater. Res., 2011, vol. 275, pp.186-91.10.4028/www.scientific.net/AMR.275.186 ↗
15. D.L. Zhang, S. Raynova, V. Nadakuduru, P. Cao, B. Gabbitas, and B. Robinson: Adv. Mater. Res., 2009, vol. 618-619, pp.513-16.10.4028/www.scientific.net/AMR.87-88.513 ↗
16. S. Raynova, D. Zhang and B. Gabbitas: Key Eng. Mater., 2012, vol. 520, pp. 289-294.10.4028/www.scientific.net/KEM.520.289 ↗
17. F. Yang, D.L. Zhang, B. Gabbitas, H.Y. Lu, and C.F. Wang: Mater. Sci. Eng. A, 2014, vol. 598, pp. 360-67.10.1016/j.msea.2014.01.055 ↗
18. L.C. Tsao, H.Y. Wu, J.C. Leong, C.J. Fang: Mater. Design, 2012, vol. 34, pp. 179-184.10.1016/j.matdes.2011.07.060 ↗
19. J. Peng, C.Y. Zhou, Q. Dai, X.H. He, Z.X. Tang, and Y.Q. Du: Rare Metal Mat. Eng., 2013, vol. 42, pp. 483-87.
20. G. Purcek, G.G. Yapici, I. Karaman, H.J. Maier: Mater. Sci. Eng. A, 2011, vol. 528, pp. 2303-08.10.1016/j.msea.2010.11.021 ↗
21. T.H. Courtney: Mechanical Behaviour of Materials, McGraw-Hill Publishing Company, New York, 1990, pp. 16.
22. M.A. Meyers, G. Subhash, B.K. Kad, and L. Prasad: Mech. Mater., 1994, vol. 17, pp. 175-93.10.1016/0167-6636(94)90058-2 ↗
23. T.H. Courtney: Mechanical Behaviour of Materials, McGraw-Hill Publishing Company, New York, 1990, pp. 13.
24. A.V. Sergueevaa, V.V. Stolyarovb, R.Z. Valievb, and A.K. Mukherjee: Scripta Mater., 2001, vol. 45, pp. 747-52.10.1016/S1359-6462(01)01089-2 ↗
25. V.V. Stolyarov, Y.T. Zhu, I.V. Alexandrov, T.C. Lowe, and R.Z. Valiev: Mater. Sci. Eng. A, 2001, vol. 299, pp. 59-67.10.1016/S0921-5093(00)01411-8 ↗
26. V.S. Zhernakov, V.V. Latysh, V.V. Stolyarov, A.I. Zharikov, and R.Z. Valiev: Scripta Mater., 2001, vol. 44, pp. 1771-74.10.1016/S1359-6462(01)00737-0 ↗
27. M.T. Jia: Ph.D. Thesis, The University of Waikato, Hamilton, 2013.
28. D.L. Zhang, C.C. Koch, and R.O. Scattergood: Mater. Sci. Eng. A, 2009, vol. 516, pp. 270-75.10.1016/j.msea.2009.03.024 ↗