journal article·2020-09

Plastic Flow During Hot Working of Ti-7Al

S. L. Semiatin, N. C. Levkulich, A. A. Salem, A. L. Pilchak

Publisher page

Abstract

Plastic flow during hot working of Ti-7Al with an equiaxed-α (fully-recrystallized) starting microstructure was quantified and interpreted via hot compression testing, metallographic/texture characterization, and internal-state-variable modeling. Isothermal, hot compression tests were conducted to axial strains of 0.2, 0.5, or 1.0 at temperatures of 1089 K, 1172 K, and 1227 K (816 °C, 899 °C, and 954 °C) and a constant true rate of 0.1 s−1. After correcting for deformation heating effects, all of the corresponding flow curves exhibited a high level of flow hardening at strains between 0 and ~ 0.2 followed by moderate hardening. Subsequent microstructure analysis via polarized-light, optical microscopy and electron-backscatter diffraction in a scanning-electron microscope revealed wrought grains containing substantial orientation gradients, small fractions (≤ 0.1) of very fine recrystallized grains at the initial grain boundaries, and small fractions of deformation twins. In view of the absence of discontinuous dynamic recrystallization except at large strains/high temperatures, viscoplastic, self-consistent (VPSC) crystal-plasticity analysis was performed to quantify the effect of crystallographic texture changes on plastic flow. For this purpose, simulations were done assuming (1) deformation via slip alone or slip plus twinning and (2) an absence of strain hardening. The VPSC simulations revealed similar texture hardening for both types of assumed deformation modes. Correction of the flow curves for such texture hardening resulted in material flow response comprising an initial strain-hardening transient followed by steady-state flow. The latter curves were analyzed in terms of the Yoshie–Laasraoui–Jonas single-state-variable formulation. The fitted dynamic-recovery and strain-hardening parameters were comparable to those found for fcc metals at hot working temperatures.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallurgy and Material Forming · Titanium Alloys Microstructure and Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (53)

Show source-provided references
1. Aerospace Structural Metals Database, CINDAS LLC, Purdue Technology Center, West Lafayette, IN, 2007.
2. J.E. Allison, M. Li, and X.M. Su: in Fundamentals of Modeling for Metals Processing, ASM Handbook, vol. 22A, D.U. Furrer and S.L. Semiatin, eds., ASM International, Materials Park, OH, 2009, pp. 7–14.
3. G.I. Taylor: J. Inst. Metals, 1938, vol. 62, pp. 307-324.
4. J.F.W. Bishop and R. Hill: Phil. Mag., 1951, vol. 42, pp. 414-427.10.1080/14786445108561065 ↗
5. J.F.W. Bishop and R. Hill: Phil. Mag., 1951, vol. 42, pp. 1298-1307.10.1080/14786444108561385 ↗
6. R.A. Lebensohn and C.N. Tome: Acta Metall. et Mater., 1993, vol. 41, pp. 2611-2624.10.1016/0956-7151(93)90130-K ↗
7. D. Dye, H.J. Stone, and R.C. Reed: Acta Mater., 2001, vol. 49, pp. 1271-128310.1016/S1359-6454(01)00003-9 ↗
8. P.R. Dawson and D.E. Boyce: in Fundamentals of Modeling for Metals Processing, ASM Handbook, vol. 22A, D.U. Furrer and S.L. Semiatin, eds., ASM International, Materials Park, OH, 2009, pp. 246–59.
9. S.L. Semiatin and T. Altan: in Metals Process Simulation, ASM Handbook, vol. 22B, D.U. Furrer and S.L. Semiatin, eds., ASM International, Materials Park, OH, 2010, pp. 46–66.10.31399/asm.hb.v22b.a0005508 ↗
10. H. Mecking and A. Beaudoin: in Fundamentals of Modeling for Metals Processing, ASM Handbook, vol. 22A, D.U. Furrer and S.L. Semiatin, eds., ASM International, Materials Park, OH, 2009, pp. 458–71.10.31399/asm.hb.v22a.a0005413 ↗
11. Y. Estrin and H. Mecking: Acta Metall., 1984, vol. 32, pp. 57-70.10.1016/0001-6160(84)90202-5 ↗
12. A. Laasraoui and J.J. Jonas: Metall. Trans., 1991, vol. 22A, pp. 1545-1560.10.1007/BF02667368 ↗
13. F. Montheillet, D. Piot, N. Matougui, and M.L. Fares: Metall. Mater. Trans. A, 2014, vol. 45, pp. 4324-4332.10.1007/s11661-014-2388-9 ↗
14. M. Semblanet, L. Pallot, D. Piot, F. Montheillet, M. Derrien, Y. Millet, C. Poletti, and C. Desrayaud: Proc. 13th World Conference on Titanium, V. Venkatesh, et al. eds., TMS, Warrandale, PA, 2016, pp. 689–94.10.1002/9781119296126.ch114 ↗
15. R.C. Picu and A. Majorell: Mater. Sci. Eng. A, 2002, vol. A326, pp. 306-316.10.1016/S0921-5093(01)01508-8 ↗
16. B. Babu and L-E. Lindgren: Inter. J. Plasticity, 2013, vol. 50, pp. 94-108.10.1016/j.ijplas.2013.04.003 ↗
17. P. Gao, H. Yang, X. Fan, and S. Zhu: J. Alloys Comp., 2014, vol. 600, pp. 74-83.
18. C. Poletti, L. Germain, F. Warchomicka, M. Dikovits, and S. Mitsche: Mater. Sci. Eng. A, 2016, vol. A651, pp. 280-290.10.1016/j.msea.2015.10.109 ↗
19. K. Hogrefe, R. Buzolin, and M.C. Poletti: Proc. 14th World Conference on Titanium, 2019, in press.
20. R. Buzolin, M. Lasnik, A. Krumphals, F. Krumphals, and M.C. Poletti: Proc. 14th World Conference on Titanium, 2019, in press.
21. I. Weiss and F.H. Froes: in Titanium ‘84: Science and Technology, G. Luetjering, U. Zwicker, and W. Bunk, eds., Deutsche Gesellschaft fur Metallkunde E.V., Oberursel, Germany, 1985, pp. 499–506.
22. F. Chaussy and J.H. Driver: in Beta Titanium Alloys, A. Vassel, D. Eylon, and Y. Combres, eds., Editions de la Revue de Metallurgie, Paris, 1994, pp. 57–64.
23. W-D. Zeng, Y-G. Zhou, and H-Q. Yu: in Titanium ’95: Science and Technology, P.A. Blenkisop, W.J. Evans, and H.M. Flower, eds., The Institute of Materials, London, 1996, pp. 683–90.
24. R. Ding, Z.X. Guo, and A. Wilson: Mater. Sci. Eng. A, 2002, vol. A327, pp. 233-245.10.1016/S0921-5093(01)01531-3 ↗
25. P. Vo, M. Jahazi, and S. Yue: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 2965-2980.10.1007/s11661-008-9666-3 ↗
26. H. Oikawa and T. Oomori: Mater. Sci. Eng. A, 1988, vol. A104, pp. 125-130.10.1016/0025-5416(88)90413-2 ↗
27. K. Ray, W.J. Poole, A. Mitchell, E.B. Hawbolt: in Advances in the Science and Technology of Titanium Alloy Processing, I. Weiss, R. Srinivasan, P. Bania, D. Eylon, S.L. Semiatin, eds., TMS Warrendale, PA, 1997, pp. 201–08.
28. Y.V.R.K. Prasad, S. Sasidhara, Hot Working Guide—A Compendium of Processing Maps, ASM, Materials Park, OH, 1997, pp. 459–61.
29. R.A.N.M. Barbos, H.C. Braga, and J. Breme: in Titanium ’92: Science and Technology, F.H. Froes and I.L. Caplan, eds., TMS, Warrendale, PA, 1993, pp. 1701–08.
30. V.G. Krishna, Y.V.R.K. Prasad, N.C. Birla, and G.S. Rao: J. Mater. Proc. Technol., 1997, vol. 71, pp. 377–383.10.1016/S0924-0136(97)00102-7 ↗
31. J. Zhao, K. Wang, L. Lv, and G. Liu: JOM, 2019, vol. 71 (7), pp. 2303-2312.10.1007/s11837-019-03490-z ↗
32. S.I. Oh, S.L. Semiatin, and J.J. Jonas: Metall. Trans. A, 1992, vol. 23A, pp. 963-975.10.1007/BF02675571 ↗
33. R.L. Goetz and S.L. Semiatin: J. Mater. Eng. Perf., 2001, vol. 10, pp. 710–17.10.1361/105994901770344593 ↗
34. H. Oikawa: in Metallurgy and Technology of Practical Titanium Alloys, S. Fujishiro, D. Eylon, and T. Kishi, eds., TMS, Warrendale, OH, 1994, pp. 93–100.
35. F. Montheillet and J.J. Jonas: in in Fundamentals of Modeling for Metals Processing, ASM Handbook, vol. 22A, D.U. Furrer and S.L. Semiatin, eds., ASM International, Materials Park, OH, 2009, pp. 220–31.10.31399/asm.hb.v22a.a0005403 ↗
36. S.L. Semiatin, D.S. Weaver, P.N. Fagin, M.G. Glavicic, R.L. Goetz, N.D. Frey, R.C. Kramb, and M.M. Antony: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 679-693.10.1007/s11661-004-0379-y ↗
37. B. Guo, S.L. Semiatin, J. Liang, B. Sun, and J.J. Jonas: Metall. Mater. Trans. A, 2018, vol. 49A, pp. 1450-1454.10.1007/s11661-018-4551-1 ↗
38. F. Larson and A. Zarkades: Properties ofTtextured Titanium Alloys, Report MCIC-74-20, Metals and Ceramics Information Center, Battelle Columbus Laboratories, Columbus, OH, 1974.
39. D.L. Olmsted, E.A. Holm, and S.M. Foiles: Acta Mater., 2009, vol. 57, pp. 3704-3713.10.1016/j.actamat.2009.04.015 ↗
40. T. Sakai, A. Belyakov, R. Kaibyshev, H. Miura, and J.J. Jonas: Prog. Mater. Sci., 2014, vol. 60, pp. 130-207.10.1016/j.pmatsci.2013.09.002 ↗
41. J.C. Williams, R.G. Baggerly, and N.E. Paton: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 837-850.10.1007/s11661-002-0153-y ↗
42. V.M. Miller, S.L. Semiatin, C. Szczepanski, and A.L. Pilchak: Metall. Mater. Trans. A, 2018, vol. 49A, pp. 3624-3636.10.1007/s11661-018-4716-y ↗
43. C.N. Tomé and R.A. Lebensohn: User’s Manual for VPSC Code, Version 7, Los Alamos National Laboratory, Los Alamos, NM, 2009.
44. D. Dunst and H. Mecking: Zeitschrift für Metallkunde, 1996, vol. 87, pp. 498-507.
45. D.G. LeoPrakash, R. Ding, R.J. Moat, I. Jones, P.J. Withers, J. QuintadaFonseca, and M. Preuss: Mater. Sci. Eng. A, 2010, vol. 527, pp. 5734-5744.10.1016/j.msea.2010.05.039 ↗
46. U.F. Kocks, C.N. Tome, and H.-R. Wenk: Texture and Anisotropy, Cambridge University Press, Cambridge, UK, 1998.
47. A. Yoshie, H. Morikawa, and Y. Onoe: Trans. ISIJ, 1987, vol. 27, pp. 425-431.10.2355/isijinternational1966.27.425 ↗
48. G.A. Sargent: Unpublished Research, Air Force Research Laboratory, Wright-Patterson Air Force Base, OH, 2007.
49. I. Lonardelli, N. Gey, H.-R. Wenk, M. Humbert, S.C. Vogel, and L. Lutterotti: Acta Mater., 2007, vol. 55, pp. 5718-5727.10.1016/j.actamat.2007.06.017 ↗
50. D. Piot, F. Montheillet, and S.L. Semiatin: Mater. Sci. Forum, 2010, vols. 638-642, pp. 2700-2705.10.4028/www.scientific.net/MSF.638-642.2700 ↗
51. Z. Guo, A.P. Miodownik, N. Saunders, and J.-P. Schillé: Scripta Mater., 2006, vol. 54, pp. 2175-2178.10.1016/j.scriptamat.2006.02.036 ↗
52. J. Lu, L. Hultman, E. Holmstrom, K.H. Antonssson, M. Grehk, W. Lei, L. Vitos, and A. Golpayegani: Acta Mater., 2016, vol. 111, pp. 39-46.10.1016/j.actamat.2016.03.042 ↗
53. M. Muzyk, Z. Pakiela, and K.J. Kurzydlowski: Metals, 2018, vol. 7, pp. 823-831.10.3390/met8100823 ↗