Thermomechanical Processing and Roll Bonding of Tri-Layered Cu-Ni-Zn/Cu-Cr/Cu-Ni-Zn Composite
Source abstract
Abstract
Tri-layered Cu-Ni-Zn/Cu-Cr/Cu-Ni-Zn composite was processed by roll bonding and the effect of thermomechanical processing on the mechanical performance and electrical conductivity was studied. Roll-bonded composite exhibited the brief work hardening and subsequent rapid work softening because of the high stored deformation energy, leading to failure at the plastic strain of 8 to 10 pct. The mechanical instability of as-roll-bonded composites was abated by heat treatment (HT) at 723 K (450 °C) and the extended work hardening with enhanced ductility compared to that of the as-roll-bonded composites was observed after HT. The strength and electrical conductivity of clad composite is dependent on the precipitation strengthening of Cu-Cr and recovery softening of Cu-Ni-Zn during post-roll-bonding HT. The increase of roll-bonding temperature enhances the precipitation kinetics and it takes shorter time to reach maximum hardness in Cu-Cr layer during post-roll-bonding HT. The toughness of as-roll-bonded Cu-Ni-Zn/Cu-Cr/Cu-Ni-Zn clad composite at 773 K (500 °C) [42 MJ/mm3] is greater than those at 723 K (450 °C) [24 MJ/mm3] and 823 K (550 °C) [38 MJ/mm3]. The maximum toughness [100 MJ/mm3] with the electrical conductivity of 68 pct IACS was obtained in the Cu-Ni-Zn/Cu-Cr/Cu-Ni-Zn clad composite roll-bonded at 773 K (500 °C) and subsequently heat-treated at 723 K (450 °C).
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. [1] I.K. Kim, S.I. Hong: Metall. Mater. Trans. A, 2013, vol. 44, pp. 3890-3900.10.1007/s11661-013-1697-8 ↗
2. [2] G. Luo, J. Zhang, M. Li, Q. Wei, Q. Shen, L, Zhang: Metall. Mater. Trans. A, 2013, vol. 44, pp. 602-605.10.1007/s11661-012-1570-1 ↗
3. [3] I.K. Kim, S.I. Hong: Mater. Des., 2013, vol. 49, pp. 935–44.10.1016/j.matdes.2013.02.052 ↗
4. [4] X. Li, G. Zu, P. Weng: Rare. Met., 2014, vol. 33, pp. 556-62.10.1007/s12598-014-0335-y ↗
5. [6] B. Aleman, I. Gutierrez, J.J. Urcola: Metall. Mater. Trans. A, 1995, vol. 26, pp. 437-46.10.1007/BF02664680 ↗
6. [7] J.S. Ha, S.I. Hong: Mater. Des., 2013, vol. 51, pp. 293-99.10.1016/j.matdes.2013.04.068 ↗
7. [9] I.K. Kim, S.I. Hong: Mater. Des., 2013, vol. 47, pp. 590–598.10.1016/j.matdes.2012.12.070 ↗
8. [10] C.Y. Chen, W.S. Hwang: Mater. Trans., 2007, vol. 48, pp. 1938-1947.10.2320/matertrans.MER2006371 ↗
9. [11] H.D. Manesh, A.K. Taheri: Mater. Des., 2003, vol. 24, pp. 617–622.10.1016/S0261-3069(03)00135-3 ↗
10. [5] I.K. Kim, S.I. Hong: Mater. Des., 2014, vol. 57, pp. 625–631.10.1016/j.matdes.2014.01.054 ↗
11. [12] Z. Chen, X. Wu, H. Hu, Q. Chen, Q. Liu: J. Mater. Eng. Perform., 2014, vol. 23, pp. 990-1001.10.1007/s11665-013-0804-8 ↗
12. [13] E.W. Jeong, K.N. Hui, D.H. Bae, D.S. Bae, Y.R. Cho: Met. Mater. Int., 2014, vol. 20, pp. 499-502.10.1007/s12540-014-3013-6 ↗
13. [14] J.Y. Song, S.I. Hong: Mater. Des., 2011, vol. 32, pp. 1790-95.10.1016/j.matdes.2010.12.036 ↗
14. [15] J.H. Su, P. Liu, Q.M. Dong, H.J. Li, F.Z. Ren, B.H. Tian: J. Mater. Eng. Perform., 2007, vol. 16, pp. 490-493.10.1007/s11665-007-9071-x ↗
15. [16] S.I. Hong, J.S. Song: Metall. Mater. Trans. A, 2001, vol. 32, pp. 985-991.10.1007/s11661-001-0356-7 ↗
16. [17] J.B. Correia, H.A. Davies, C.M. Sellars: Acta. Mater., 1997, vol. 45, pp. 177-190.10.1016/S1359-6454(96)00142-5 ↗
17. [18] P. Liu, J. Sui, Q. Dong, H. Li: J. Mater. Sci. Technol., 2005, vol. 21, pp. 475-478.
18. [19] D. Raabe, K. Miyake, H. Takahara: Mater. Sci. Eng. A, 2000 vol. 291, pp. 186–19710.1016/S0921-5093(00)00981-3 ↗
19. [20] D. Raabe, P.-P. Choi, Y. Li, A.Kostka, X. S., F. Lecouturier, K. Hono, R. Kirchheim, R. Pippan and D. Embury. MRS Bulletin, 2010, vol. 35, pp 982-991.10.1557/mrs2010.703 ↗
20. [21] D. Raabe, S. Osaki, K. Hono, Acta Materialia, 2009, 57, pp. 5254-63.10.1016/j.actamat.2009.07.028 ↗
21. T.W. Heo, S. Bhattacharyya, L.Q. Chen: Acta. Mater., 2011, vol. 59, pp. 7800–15.10.1016/j.actamat.2011.08.045 ↗
22. [23] N. Jia, F. Roters, P. Eisenlohr, D. Raabe, X. Zhao, Acta Mater, 2013, 61, pp. 4591-4606.;10.1016/j.actamat.2013.04.029 ↗
23. [24] N. Jia, D. Raabe, X. Zhao, Acta Mater, 2014, 76, pp. 238-51.10.1016/j.actamat.2014.05.036 ↗
24. [25] W. N. Kim, S.I. Hong: Mater. Sci. Eng. A, 2016, vol. 651, pp. 976-86.10.1016/j.msea.2015.11.062 ↗
25. S.C. Krishna, N.K. Gangwar, A.K. Jha, B. Pant, and K.M. George: J. Mater. Eng. Perform., 2014, vol. 23, pp. 1458–64.10.1007/s11665-014-0882-2 ↗
26. [27] U.F. Kocks: Metall. Trans. A., 1985, vol. 16, pp. 2109-29.10.1007/BF02670415 ↗
27. [28] S.I. Hong, C. Laird: Acta. Metall. Mater., 1990, vol. 38, pp. 1581-94.10.1016/0956-7151(90)90126-2 ↗
28. [29] W.F. Smith: Structure and Properties of Engineering Alloy, 2nd ed., McGraw-Hill Book Co., New York, 1993, pp. 282-284.
29. [30] T.H. Alden: Metall. Trans. A, 1976, vol. 7, pp. 1057-63.10.1007/BF02656587 ↗
30. [31] T. Ito, Y. Nakayama: J. Mater. Sci., 1988, vol. 23, pp. 2174-80.10.1007/BF01115785 ↗
31. [8] J.Y. Jin, S.I. Hong: Mater. Sci. Eng. A, 2014, vol. 596, pp. 1-8.10.1016/j.msea.2013.12.019 ↗
32. [32] J.D. Verhoeven, H.L. Downing, L.S. Chumbley, E.D. Gibson: J. Appl. Phys., 1989, vol. 65, pp. 1293-1301.10.1063/1.343024 ↗