Microstructure-Based FEM Modeling of Phase Transformation During Quenching of Large-Size Steel Forgings
Source abstract
Abstract
The current investigation encompasses the development of a microstructure-based 3D finite element model (FEM) of water quenching process of large-size, high-strength steel forgings with accurate predictions of the volume fraction of phases. The approach is based on modified TTT/CCT curves that consider a lower martensite start temperature value. An experimental procedure consisting in the validation of the FEM simulations was conducted using high-resolution dilatometry, optical and scanning electron microscopy, and instrumentation of a large-size steel block with several thermocouples at different locations. Results showed a very good agreement between the temperature predictions of the 3D FEM model and those obtained from direct measurement of instrumented forged block with an average error of about 1 pct in the quarter region. The volume fraction of phases and hardness distribution across the block were also predicted by the proposed 3D FEM model. The numerical results revealed bainitic volume fractions of about 74 pct at the center of the block and about 91 pct in the quarter region. These predictions were also confirmed by dilatometry test and metallographic examination of the microstructure. Micro hardness measurements were conducted on dilatometry samples that simulate the heat treatment cycle of different thicknesses of the forged block were compared with those predicted by the FEM, and very good agreements were obtained, further confirming the validity of the simulations. The proposed procedure in this research improves the quality of predictions by increasing the reliability of material parameters such as TTT optimization and accurate determination of thermo-physical parameters.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (76)
Show source-provided references
1. D. Firrao, P. Matteis, G. Scavino, G. Ubertalli, M. G. Ienco, M. R. Pinasco, E. Stagno, R. Gerosa, B. Rivolta, A. Silvestri, G. Silva, and A. Ghidini, Mat Sci Eng a-Struct 2007, vol. 468, pp. 193-200.10.1016/j.msea.2006.07.166 ↗
2. K. Chadha, D. Shahriari, and M. Jahazi, Int. J. Ital. Assoc. Metall 2016, vol. 4, pp. 5-12.
3. A. Michael, K. Nikolai, and P. Joseph, Industrial-Scale Intensive Quenching Process for Tool Products Commercialization, EMTEC report no. EMTEC CT-76-II, Edison Material Technology Center (EMTEC), Dayton, OH, 2005.
4. K. Araki, T. Yuasa, and Y.-T. Tamura Heat-Treated Steel Plates with Heavy Section and Large Product Weight, JFE TECHNICAL REPORT No. 18 2013, p. 7.
5. F. Beaudet, C. Blais, H. Lehuy, B. Voyzelle, G. Lespérance, J.-P. Masse, and M. Krishnadev, ISIJ international 2012, vol. 52, pp. 424-433.10.2355/isijinternational.52.424 ↗
6. N. I. Kobasko, W. S. Morhuniuk, and B. K. Ushakov: Design of Steel-Intensive Quench Processes. CRC Press, New York, 2007.
7. M. Narazaki, G. Totten, and G. Webster, Hardening by Reheating and Quenching, Wiley, New York, 2002. pp 248-295.
8. B. P. Maradİt, Master’s dissertation: Middle East Technical University, 2010.
9. M. Jung, M. Kang, and Y.-K. Lee, Acta Materialia 2012, vol. 60, pp. 525-536.10.1016/j.actamat.2011.10.007 ↗
10. C. Şimşir and C. H. Gür, S. Vestnik, Journal of Mechanical Engineering 2010, vol. 56, pp. 93-103.
11. Z. Guo, N. Saunders, A. P. Miodownik, and J.-P. Schillé, International Journal of Metallurgical Engineering 2013, vol. 2, pp. 198-202.
12. K. Babu and T. P. Kumar, Metall and Materi Trans B 2014, vol. 45, pp. 1530-1544.10.1007/s11663-014-0069-0 ↗
13. Z. Guo, N. Saunders, P. Miodownik, and J. Schille, Int. J. Microstructure and Materials Properties 2009, vol. 4, pp. 187-195.
14. F. BrazFernandes, S. Denis, and A. Simon, Materials Science and Technology 1985, vol. 1, pp. 838-844.10.1179/mst.1985.1.10.838 ↗
15. J. Pan and J. Gu, Mathematical Fundamentals of Thermal Process Modeling of Steels, ed, Cemil Hakan; Gur and Jiansheng; Pan, 2008. pp 1-62.10.1201/9781420003581.ch1 ↗
16. C. Şimşir, Simulation of Quenching, CRC Press, Taylor & Francis Group, Bpoca RATON, 2009.
17. J. W. Cahn, Acta Metallurgica 1956, vol. 4, pp. 572-575.10.1016/0001-6160(56)90158-4 ↗
18. E. B. Hawbolt, B. Chau, and J. K. Brimacombe, Metallurgical Transactions A 1983, vol. 14, pp. 1803-1815.10.1007/BF02645550 ↗
19. F. Liu, C. Yang, G. Yang, and Y. Zhou, Acta Materialia 2007, vol. 55, pp. 5255-5267.10.1016/j.actamat.2007.05.041 ↗
20. M. Lusk and H.-J. Jou, Metallurgical and Materials Transactions A 1997, vol. 28, pp. 287-291.10.1007/s11661-997-0131-5 ↗
21. M. T. Todinov, Metall and Materi Trans B 1998, vol. 29, pp. 269-273.10.1007/s11663-998-0030-1 ↗
22. H. J. M. Geijselaers, Doctoral dissertation: University of Twente, Enschede, 2003.
23. B. Buchmayr and J. S. Kirkaldy, J. Heat Treating 1990, vol. 8, pp. 127-136.10.1007/BF02831633 ↗
24. M. V. Li, D. V. Niebuhr, L. L. Meekisho, and D. G. Atteridge, Metall and Materi Trans B 1998, vol. 29, pp. 661-672.10.1007/s11663-998-0101-3 ↗
25. Z. Guo, N. Saunders, P. Miodownik, and J.-P. Schillé, International Journal of Microstructure and Materials Properties 2009, vol. 4, pp. 187-195.
26. N. Saunders, Z. Guo, X. Li, A. P. Miodownik, and J.-P. Schillé The Calculation of TTT and CCT diagrams for General Steels, Sente Software Ltd.,U.K 2004.
27. M. Peterli, M.-T. Truong, N. Manopulo, and P. Hora, MATEC Web of Conferences 2016, vol. 80, p. 10010.10.1051/matecconf/20168010010 ↗
28. H. K. D. H. Bhadeshia: Bainite in Steels—Transformations, Microstructure and Properties. IOM Communications, 2001.
29. ASM-International-Handbook-Committee: ASM Handbook, Heat Treating. ASM International, 1991.
30. J. R. Davis, In Book: Basic Principles and Design Guidelines for Heat Treating of Steel, ed, Joseph R. Davis ASM International, 1998. pp 961–70.10.31399/asm.hb.mhde2.a0003195 ↗
31. C. Şimşir, Doctoral dissertation: Middle East Technical University, 2008.
32. M. Boniardi, M. Guagliano, A. Casaroli, R. Andreotti, and F. Ballerini, Materials Performance and Characterization 2014, vol. 3, pp. 118–136.
33. Y. Bouissa, D. Shahriari, H. Champliaud, and M. Jahazi, Case Studies in Thermal Engineering 2019, vol. 13, p. 100379.10.1016/j.csite.2018.100379 ↗
34. FORGE® for heat treatment. https://www.transvalor.com/en/blog/forge-for-heattreatment. Accessed 9 Mar 2021.
35. D.A. Wang, Proceedings of the 29th National Conference on Mechanical Engineering of CSME, December 6-7, 2013, I-Lan, Taiwan 2013.
36. E. Ben Fredj, H. G. Nanesa, D. Shahriari, J.-B. Morin, and M. Jahazi. Effect of Cooling Rate on Phase Transformation and Microstructure Evolution in a Large Size Forged Ingot of Medium Carbon Low Alloy Steel. in TMS 2017 2017. Cham: Springer International Publishing.10.1007/978-3-319-51493-2_39 ↗
37. S. Wei, In Book: Physical Metallurgy of Thermal Processing, CRC Press, 2008.
38. U. S. S. Corporation: Atlas of isothermal transformation diagrams. United States Steel, 1951.
39. D. Cardinaux, Doctoral dissertation: Ecole Nationale Supérieure des Mines de Paris, 2008.
40. Z. Guo, N. Saunders, J. P. Schillé, and A. P. Miodownik, Materials Science and Engineering: A 2009, vol. 499, pp. 7-13.10.1016/j.msea.2007.09.097 ↗
41. O. Mustak, E. Evcil, and C. Şimşir, Materialwissenschaft und Werkstofftechnik 2016, vol. 47, pp. 735-745.10.1002/mawe.201600607 ↗
42. N. Saunders, U. K. Z. Guo, X. Li, A. P. Miodownik, and J. P. Schillé, JOM 2003, vol. 55, pp. 60-65.10.1007/s11837-003-0013-2 ↗
43. K. Shinzato and T. Baba, Journal of Thermal Analysis and Calorimetry 2001, vol. 64, pp. 413-422.10.1023/A:1011594609521 ↗
44. S. Miao, H. Li, and G. Chen, Journal of Thermal Analysis and Calorimetry 2014, vol. 115, pp. 1057–1063.10.1007/s10973-013-3427-2 ↗
45. S. Poncsák, A. E. Gheribi, L. I. Kiss, P. Chartrand, S. Guérard, and J. F. Bilodeau, Journal of Thermal Analysis and Calorimetry 2019, vol. 135, pp. 2059-2068.10.1007/s10973-018-7435-0 ↗
46. Y. Takahashi, International Journal of Thermophysics 1984, vol. 5, pp. 41-52.10.1007/BF00502078 ↗
47. R. E. Taylor, J. Gembarovic, and K. D. Maglic: Thermal Diffusivity by the Laser Flash Technique, Second Edition. Wiley, New York, 2002.
48. J. Cochet, S. Thuillier, T. Loulou, N. Decultot, P. Carré, and P.-Y. Manach, The International Journal of Advanced Manufacturing Technology 2017, vol. 91, pp. 2329-2346.10.1007/s00170-016-9951-z ↗
49. A. Kulawik and A. Bokota, Archives of Metallurgy and Materials 2011, vol. 56, pp. 345-357.10.2478/v10172-011-0037-5 ↗
50. D. M. Zhu, G. Y. Liu, S. J. Zhang, and M. W. Li, Ironmaking & Steelmaking 2014, vol. 41, pp. 329-334.10.1179/1743281213Y.0000000137 ↗
51. F. Beaudet, Master’s dissertation: Université Laval, 2009.
52. S. M. Chentouf, M. Jahazi, L.-P. Lapierre-Boire, and S. Godin, Metallography, Microstructure, and Analysis 2014, vol. 3, pp. 281-297.10.1007/s13632-014-0142-8 ↗
53. Y. Luo, X.-c. Wu, Y.-a. Min, Z. Zhu, and H.-b. Wang, Journal of Iron and Steel Research, International 2009, vol. 16, pp. 61-67.10.1016/S1006-706X(09)60029-7 ↗
54. D. I. Li and M. A. Wells, Metall and Materi Trans B 2005, vol. 36, pp. 343-354.10.1007/s11663-005-0064-6 ↗
55. ImageJ. Image Processing and Analysis in Java. Available from: https://imagej.nih.gov/ij/.
56. F. Caballero, M. Santofimia, C. Garcia-Mateo, and C. García de Andrés, Materials Transactions 2004, vol. 45, pp. 3272-3281.10.2320/matertrans.45.3272 ↗
57. D. Quidort and Y. J. M. Brechet, ISIJ International 2002, vol. 42, pp. 1010-1017.10.2355/isijinternational.42.1010 ↗
58. P. Cao, G. Liu, and K. Wu, International Journal of Material and Mechanical Engineering 2012, vol. 1, pp. 16-20.
59. B. Liščić and G.E. Totten, In: J.L. Dossett and G.E. Totten (eds.) Inverse Hardening. ASM International, Materials Park, 2013.10.31399/asm.hb.v04a.a0005788 ↗
60. K. Arimoto, C. Jin, S. Tamura, K. Funatani, and M. Tajima, Transactions of Materials and Heat Treatment 2004, vol. 25, pp. 465-470.
61. M.-x. Zhou, G. Xu, L. Wang, Z.-l. Xue, and H.-j. Hu, Met Mater Int 2015, vol. 21, pp. 985-990.10.1007/s12540-015-2348-y ↗
62. E. Ben Fredj, Doctoral dissertation: École de technologie supérieure, Montréal, 2019.
63. H. Talebi, H. GhasemiNanesa, M. Jahazi, and H. Melkonyan, Materials Science Forum 2018, vol. 941, pp. 305-310.10.4028/www.scientific.net/MSF.941.305 ↗
64. S. H. Talebi, Master’s dissertation: École de technologie supérieure, Montreal, 2018.
65. H. K. D. H. Bhadeshia: Bainite in Steels – Transformation, Microstructure and Properties. Maney Publishing, Leeds, 2001.
66. C. Goulas, M. G. Mecozzi, and J. Sietsma, Metallurgical and Materials Transactions A 2016, vol. 47, pp. 3077-3087.10.1007/s11661-016-3418-6 ↗
67. I. Stark, G. D. W. Smith, and H. K. D. H. Bhadeshia, Metall Trans A 1990, vol. 21, pp. 837-844.10.1007/BF02656567 ↗
68. B. Avishan, C. Garcia-Mateo, L. Morales-Rivas, S. Yazdani, and F. G. Caballero, J Mater Sci 2013, vol. 48, pp. 6121-6132.10.1007/s10853-013-7408-4 ↗
69. F. G. Caballero, H. K. D. H. Bhadeshia, K. J. A. Mawella, D. G. Jones, and P. Brown, Materials Science and Technology 2013, vol. 17, pp. 512-516.10.1179/026708301101510348 ↗
70. C. Garcia-Mateo and F. G. Caballero, Materials Transactions 2005, vol. 46, pp. 1839-1846.10.2320/matertrans.46.1839 ↗
71. X. L. Wang, K. M. Wu, F. Hu, L. Yu, and X. L. Wan, Scripta Materialia 2014, vol. 74, pp. 56-59.10.1016/j.scriptamat.2013.10.019 ↗
72. L. Zhao, L. Qian, Q. Zhou, D. Li, T. Wang, Z. Jia, F. Zhang, and J. Meng, Materials and Design 2019, vol. 183, p. 108123.10.1016/j.matdes.2019.108123 ↗
73. A. Grajcar, P. Skrzypczyk, and A. Kozłowska, Applied Sciences 2018, vol. 8, p. 2156.10.3390/app8112156 ↗
74. H. K. D. H. Bhadeshia: Bainite in Steels—Theory And Practice. Maney Publishing, Leeds, 2015.
75. F.G. Caballero, M.J. Santofimia, C. Capdevila, C. García-Mateo, and C. GarcíaDeAndrés, ISIJ Int. 46: 1479 (2006)10.2355/isijinternational.46.1479 ↗
76. P. H. Shipway and H. K. D. H. Bhadeshia, Materials Science and Technology 2013, vol. 11, pp. 1116-1128.10.1179/mst.1995.11.11.1116 ↗