Nanoparticles Reinforcement for the Improved Strength and High-Temperature Wear Resistance of Mn-Cr Steel
Source abstract
Abstract
Nanotechnologies offer tremendous potential when it comes to modifying the microstructure of steel through the incorporation of nanoparticles. While typical production methods for metal-matrix composites are difficult and expensive, conventional casting routes suffer from inhomogeneity and agglomeration of the added nanoparticles. The aim of this study was to investigate the feasibility and possibilities of introducing nanosized particles into a steel matrix through a conventional casting process and to determine the effect of different nanoparticles and methods of incorporation on the strength, toughness, and high-temperature wear resistance of martensitic steel. The results show that also in the case of a conventional casting process, it is possible to obtain a homogeneous distribution of nanoparticles in the metal matrix, resulting in improved strength, maintained toughness, and up to five times better high-temperature wear resistance of the Mn-Cr steel. However, the rate of improvement greatly depends on the method and type of nanoparticles incorporation. The most promising results were observed for the combination of carbon nanotubes, oxide nanoparticles, and dispersant, sealed in a steel tube, with the dispersant providing the uniform distribution, the carbon nanotubes delivering the good toughness and the adhesive wear properties, and the oxide nanoparticles ensuring oxidation and abrasive wear resistance.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced materials and composites · Tribology and Wear Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. [1] R. Kuziak, R. Kawalla and S. Waengler: Arch. Civ. Mech. Eng., 2008, vol. 8, pp. 103–117.10.1016/S1644-9665(12)60197-6 ↗
2. [2] G. Jha, S. Das, S Sinha, A. Lodh and A. Haldar: Mater. Sci. Eng. A-Struct., 2013, vol. 561, pp. 394–402.10.1016/j.msea.2012.10.047 ↗
3. [3] W.J. Nam, C.S. Lee and D.Y. Ban: Mater. Sci. Eng. A-Struct., 2000, vol. 289, pp. 8–17.10.1016/S0921-5093(00)00928-X ↗
4. [4] P.K. Mallick: Materials, Design and Manufacturing for Lightweight Vehicles, Woodhead Publishing Limited, Cambridge, 2010.10.1533/9781845697822 ↗
5. [5] F. Ozturk, A. Polat, S. Toros and R.C. Picu: J. Iron Steel Res. Int., 2013, vol. 20, pp. 68–74.10.1016/S1006-706X(13)60114-4 ↗
6. [6] B. Podgornik, M. Torkar, J. Burja, M. Godec and B. Senčič: Mater. Sci. Eng. A-Struct., 2015, vol. 638, pp. 183–189.10.1016/j.msea.2015.04.082 ↗
7. [7] B. Podgornik, V. Leskovšek, M. Godec and B. Senčič: Mater. Sci. Eng. A-Struct., 2014, vol. 599, pp. 81–86.10.1016/j.msea.2014.01.054 ↗
8. [8] B. Nie, Z. Zhang, Z. Zhao and Q. Zhong: Mater. Design., 2013, vol. 50, pp. 503–508.10.1016/j.matdes.2013.03.039 ↗
9. [9] Chao-lei Zhang, Ya-zheng Liu, Chao Jiang and Jin-fu Xiao: J. Iron Steel Res. Int., 2011, vol. 18, pp. 49–53.10.1016/S1006-706X(11)60077-0 ↗
10. [10] Chao-lei Zhang, Ya-zheng Liu, Le-yu Zhou and Chao Jiang: J. Iron Steel Res. Int., 2012, vol. 19, pp. 47–51.10.1016/S1006-706X(12)60072-7 ↗
11. [11] W. Zhou, H. Guo, Z. Xie, X. Wang and C. Shang: Mater. Sci. Eng. A-Struct., 2013, vol. 587, pp. 365–371.10.1016/j.msea.2013.06.022 ↗
12. Barani A. A., F. Li, P. Romano, D. Ponge and D. Raabe: Mater. Sci. Eng. A, 2007, vol. 463, pp. 138–146.10.1016/j.msea.2006.08.124 ↗
13. [13] E. Pagounis and V.K. Lindroos: Mater. Sci. Eng. A-Struct., 1998, vol. 246, pp. 221–234.10.1016/S0921-5093(97)00710-7 ↗
14. [14] I.A. Ibrahim, F.A. Mohamed and E.J. Lavernia: J. Mater. Sci., 1991, vol. 26, pp. 1137–1156.10.1007/BF00544448 ↗
15. [15] D.J. Lloyd: Int. Mater. Rev., 1994, vol. 39, pp. 1–23.10.1179/imr.1994.39.1.1 ↗
16. [16] A. Luo: Metall. Mater. Trans. A, 1995, vol. 26, pp. 2445–2455.10.1007/BF02671259 ↗
17. [17] K.U. Kainer: Metal matrix composites. Custom-made materials for automotive and aerospace engineering, Wiley-VCH Verlag GmbH, Weinheim, 2003.
18. [18] F. Akhtar: Can. Metall. Quart., 2014, vol. 53, pp. 253–263.10.1179/1879139514Y.0000000135 ↗
19. [19] F. Akhtar, S. Guo, J. Askari and J. Tian: J. Univ. Sci. Technol. B, 2007, vol. 14, pp. 89–93.10.1016/S1005-8850(07)60018-8 ↗
20. [20] S.C. Tjong and K.C. Lau: Mater. Lett., 1999, vol. 41, pp. 153–158.10.1016/S0167-577X(99)00123-8 ↗
21. [21] I. Sulima, P. Klimczyk and P. Malczewski: Acta Metall. Sin.-Engl., 2014, vol. 27, pp. 12–18.10.1007/s40195-013-0002-6 ↗
22. [22] X.W. Zeng, W.G. Zhang, N. Wei, R.P. Liu and M.Z. Ma: Mater. Sci. Eng. A-Struct., 2007, vol. 443, pp. 224–228.10.1016/j.msea.2006.08.030 ↗
23. [23] Q.C. Jiang, X.L. Li and H.Y. Wang: Scripta Mater., 2003, vol. 48, pp. 713–717.10.1016/S1359-6462(02)00551-1 ↗
24. [24] Dongshuai Zhou, Feng Qiu, Huiyuan Wang and Qichuan Jiang: Acta Metall. Sin.-Engl., 2014, vol. 27, pp. 798–805.10.1007/s40195-014-0154-z ↗
25. [25] M. Bahrami, K. Dehghani and M.K.B. Givi: Mater. Design., 2014, vol. 53, pp. 217–225.10.1016/j.matdes.2013.07.006 ↗
26. [26] D.S. Zhou, F. Qiu and Q.C. Jiang: Mater. Sci. Eng. A-Struct., 2014, vol. 596, pp. 98–102.10.1016/j.msea.2013.12.049 ↗
27. [27] S. Chen, P. Seda, M. Krugla and A. Rijkenberg: Mat. Sci. Tech., 2016, vol. 32, pp. 992–1003.10.1080/02670836.2015.1104082 ↗
28. [28] K.I. Parashivamurthy, M.N. Chandrasekharaiah, P. Sampathkumaran and S. Seetharamu: Mater. Manuf. Process., 2006, vol. 21, pp. 473–478.10.1080/10426910500471474 ↗
29. [29] J. Hashim, L. Looney and M.S.J. Hashmi: J. Mater. Process. Tech., 1999, vol. 92–93, pp. 1–710.1016/S0924-0136(99)00118-1 ↗
30. [30] Jin-Ju Park, Sung-Mo Hong, Eun-Kwang Park, Kyeong-Yeol Kim, Min-Ku Lee and Chang-Kyu Rhee: Mater. Sci. Eng. A-Struct., 2014, vol. 613, pp. 217–223.10.1016/j.msea.2014.06.103 ↗
31. [31] Sang-Hoon Lee, Sung-Mo Hong, Byoung-Sun Han, Jin-Ju Park, Jong-Keuk Lee, Jung-Gu Lee, Min-Ku Lee and Chang-Kyu Rhee: J. Nanosci. Nanotechno., 2010, vol. 10, pp. 258–262.10.1166/jnn.2010.1529 ↗
32. [32] R. Lazarova, R.H. Petrov, V. Gaydarova, A. Davidkov, A. Alexeev, M. Manchev and V. Manolov: Mater. Design., 2011, vol. 32, pp. 2734–2741.10.1016/j.matdes.2011.01.024 ↗
33. [33] S.A. Chernyak, A.S. Ivanov, N.E. Strokova, K.I. Maslakov, S.V. Savilov and V.V. Lunin: J. Phys. Chem. C, 2016, vol. 120, pp. 17465–17474.10.1021/acs.jpcc.6b05178 ↗
34. [34] S.A. Chernyak, E.V. Suslova, A.S. Ivanov, A.V. Egorov, K.I. Maslakov, S.V. Savilov and V.V. Lunin: Appl. Catal. A-Gen., 2016, vol. 523, pp. 221–229.10.1016/j.apcata.2016.06.012 ↗
35. [35] F. Velasco, W.M. Lima, N. Anton, J. Abenojar and J.M. Torralba: Tribol. Int., 2003, vol. 36, pp. 547–551.10.1016/S0301-679X(02)00264-5 ↗
36. [36] B. Podgornik, B. Zuzek and V. Leskovsek: Mater. Perform. Charact., 2014, vol. 3, pp. 87–103.10.1520/MPC20130045 ↗
37. [37] E.E. Gdoutos: Fracture Mechanics Criteria and Applications, Kluwer Academic Publishers, London, 1990.10.1007/978-94-009-1956-3 ↗
38. [38] Z. Amondarain, M. Arribas, J.L. Arana and G.A. Lopez: Mater. Trans., 2013, vol. 54, pp. 1867–1876.10.2320/matertrans.M2013073 ↗
39. [39] B. Podgornik, V. Leskovšek: Metall. Mater. Trans. A, 2013, vol. 44, pp. 5694–5702.10.1007/s11661-013-1921-6 ↗
40. M. Fernández-Garcia and J.A. Rodriguez: in Encyclopedia of Inorganic Chemistry, Wiley, 2009. https://doi.org/10.1002/0470862106.ia377.10.1002/0470862106.ia377 ↗