Investigation of Hardness Change for Spot Welded Tailored Blank in Hot Stamping Using CCT and Deformation-CCT Diagrams
Source abstract
Abstract
When an outer panel of a B-pillar is manufactured with the hot stamping process, reinforcements are spot welded on its inner side. Before reinforcements are added, the microstructure of the outer panel is martensite. However, reheating during spot welding changes the martensite to ferrite, which has a lower hardness in the heat-affected zone than in other areas. If spot welding is conducted before hot stamping for making a spot welded tailored blank, the microstructure in the spot welded tailored blank after hot stamping is martensite. This sequence of processes avoids hardness reduction due to spot welding. In this study, the hardness and microstructure around spot welded parts of the tailored blank were investigated. The results clearly showed that areas close to the spot welded parts are severely stretched during hot stamping. In addition, stretching suppresses the martensitic phase transformation and reduces the hardness. To characterize this phenomenon, a simulation was conducted that considered the effects of pre-strain on the phase transformation. A continuous cooling transformation (CCT) diagram and a deformation continuous cooling transformation (DCCT) diagram were made in order to quantify the effect of the cooling rate and pre-strain on the phase transformation and hardness. The hardness was then calculated using the experimentally measured CCT and DCCT diagrams and the finite element analysis results. The calculated hardness was compared with the experimental hardness. Good agreement was found between the calculated and experimental results.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. H. Karbasian, A.E. Tekkaya, J. Mater. Process. Technol., (2010), 210, pp. 2103 - 211810.1016/j.jmatprotec.2010.07.019 ↗
2. M. Merklein, J. Lechler, J. Mater. Process. Technol., (2006), 177, pp. 452 - 455.10.1016/j.jmatprotec.2006.03.233 ↗
3. Y. Yogo, M. Kamiyama, T. Iwata, N. Iwata, T. Ishikawa, Metall. Mater. Trans. A, (2012), 43A, pp. 893 – 89910.1007/s11661-011-0919-1 ↗
4. P.F. Bariani, S. Bruschi, A. Ghiotti, A. Turetta, CIRP Ann. Manuf. Technol., (2008), 57, pp. 265 – 26810.1016/j.cirp.2008.03.049 ↗
5. J.Y. Min, J.P. Lin, J.Y. Li, W.H. Bao, Comput. Mater. Sci., (2010), 49, pp. 326 - 33210.1016/j.commatsci.2010.05.018 ↗
6. Cui Junjia, Sun Guangyong, Xu Junrui, Huang Xiaodong Li Guangyao, Mater Des, (2015) 77, pp. 95-10910.1016/j.matdes.2015.04.009 ↗
7. R. Kolleck, R. Veit, M. Merklein, J. Lechler, M. Geiger, CIRP Ann. Manuf. Technol., (2009), 58, pp. 275 - 27810.1016/j.cirp.2009.03.090 ↗
8. M. Naderi, A. Saeed-Akbari, W. Bleck, Mater. Sci. Eng. A: Struct. 487 (2008) 445–455.10.1016/j.msea.2007.10.057 ↗
9. A. Barcellona, D. Palmeri, Metall. Mater. Trans. A, (2009), 40A, pp. 1160 - 1174.10.1007/s11661-009-9790-8 ↗
10. M. Nikravesh, M. Naderi, G.H. Akbari, W. Bleck, Mater. Des., (2015), 84, pp. 18 – 2410.1016/j.matdes.2015.06.108 ↗
11. Z. Shi, K. Liu, M. Wang, J. Shi, H. Dong, J. Pu, B. Chi, Y. Zhang, L. Jian, Mater. Sci. Eng. A (2012), 535, pp. 290–96.10.1016/j.msea.2011.12.088 ↗
12. N. Li, J. Lin, D.S. Balint, T.A. Dean, J. Mater. Process. Technol., (2016) 231, pp. 254-26410.1016/j.jmatprotec.2015.12.008 ↗
13. Bernd M. Linke, Thomas Gerber, Ansgar Hatscher, Ilaria Salvatori, Iñigo Aranguren, Maribel Arribas, Metall. Mater. Trans. A, (2018) 49, pp. 54–6510.1007/s11661-017-4400-7 ↗
14. A. Bardelcik, C.S. Salisbury, S. Winkler, M.A. Wells, M.J. Worswick, Int. J. Impact Eng., (2010), 37, pp. 694 - 702.10.1016/j.ijimpeng.2009.05.009 ↗
15. Marion Merklein, Michael Wieland, Michael Lechner, Stefania Bruschi, Andrea Ghiotti, J. Mater. Process. Technol., (2016) 228, pp. 11-2410.1016/j.jmatprotec.2015.09.023 ↗
16. Prasun Chokshi, Richard Dashwood, Darren J. Hughes, Comput Struct, (2017) 190, pp. 162-17210.1016/j.compstruc.2017.05.015 ↗
17. Yanhong Mu, Baoyu Wang, Jing Zhou, Xu Huang, Xuetao Li, Metall. Mater. Trans. A, (2017) 48, pp. 5467–547910.1007/s11661-017-4270-z ↗
18. Shiqi Zhang, Yunhua Huang, Bintang Sun, Qingliang Liao, Hongzhou Lu, Bian Jian, Hardy Mohrbacher, Wei Zhang, Aimin Guo, Yue Zhang, Mater Sci Eng A, (2015) 626, pp. 136-14310.1016/j.msea.2014.12.051 ↗
19. Hye-Jin Kim, Soon-Hyeok Jeon, Won-Seog Yang, Byung-Gil Yoo, Yoo-Dong Chung, Heon-Young Ha, Hyun-Young Chung, J Alloys Compd, (2018) 735, pp. 2067-208010.1016/j.jallcom.2017.12.004 ↗
20. H. Fujimoto, M. Yasuyama, H. Ueda. R. Ueji, and H. Fujii, Q. J. Jpn. Weld. Soc., 2015, vol. 33, pp. 144–52 (in Japanese).10.2207/qjjws.33.144 ↗
21. H. Fujimoto, H. Ueda, E. Nakayama, R. Ueji and H. Fujii, Q. J. Jpn. Weld. Soc., (2015), 33, pp. 253-261 (in Japanese)10.2207/qjjws.33.253 ↗
22. Hiroki Fujimoto, Masanori Yasuyama, Hideki Ueda, Rintaro Ueji, Hidetoshi Fujii, Weld Int, (2017) 31, pp. 681-69110.1080/09507116.2016.1223224 ↗
23. Taherian Reza, Najafizadeh Abbas, Shateri Reza, J. Mater. Process. Technol., (2008), 196, pp. 321 – 33110.1016/j.jmatprotec.2007.05.059 ↗
24. M. Opiela, W. Zalecki, A. Grajcar, Journal of Achievements in Materials and Manufacturing Engineering, (2012), 51, pp. 78 – 89
25. R. Kawulok, I. Sshindler, P. Kawulok, S. Rusz, P. Opela, Z. Solowski, K. M. Cmiel, METALURGIJA, (2015), 54, pp. 473 – 476
26. S. Rusz, I. Schindler, P. Kawulok, R. Kawulok, P. Opela, J. Kliber, Z. Solowski, METALURGIJA, (2016), 55, pp. 655 - 658
27. H.-H. Bok, M.-G. Lee, E.J. Pavlina, F. Barlat, H.-D. Kim,, Int. J. Mech. Sci., (2011), 53, pp. 744 – 5210.1016/j.ijmecsci.2011.06.006 ↗
28. Junjia Cui, Chengxi Lei, Zhongwen Xing, Chunfeng Li, and Shumei Ma, J. Mater. Eng. Perform., 21 (2012), pp. 2244 – 225410.1007/s11665-012-0180-9 ↗
29. W. Weiß, R. Kolleck, M. Machhammer, and F. Krall: 4th International Conference Hot Sheet Metal Forming of High-Performance Steel CHS2, Sweden Proceedings, June 9–12, 2013, Luleå, 2013, pp. 91–98.
30. LSTC: LS-DYNA Keyword User’s Manual Version 9.71. Livermore Software Technology Corporation, July 2006.