journal article·2018-06

Application of Precipitate Free Zone Growth Kinetics to the β-Phase Depletion Behavior in a CoNiCrAlY Coating Alloy: An Analytical Approach

H. Chen

Publisher page

Abstract

This paper concerns the β-phase depletion kinetics of a thermally sprayed free-standing CoNiCrAlY (Co-31.7 pct Ni-20.8 pct Cr-8.1 pct Al-0.5 pct Y, all in wt pct) coating alloy. An analytical β-phase depletion model based on the precipitate free zone growth kinetics was developed to calculate the β-phase depletion kinetics during isothermal oxidation. This approach, which accounts for the molar volume of the alloy, the interfacial energy of the γ/β interface, and the Al concentration at γ/γ + β boundary, requires the Al concentrations in the β-phase depletion zone as the input rather than the oxidation kinetics at the oxide/coating interface. The calculated β-phase depletion zones derived from the current model were compared with experimental results. It is shown that the calculated β-phase depletion zones using the current model are in reasonable agreement with those obtained experimentally. The constant compositional terms used in the model are likely to cause the discrepancies between the model predictions and experimental results. This analytical approach, which shows a reasonable correlation with experimental results, demonstrates a good reliability in the fast evaluation on lifetime prediction of MCrAlY coatings.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · High Temperature Alloys and Creep · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (69)

Show source-provided references
1. J.R. Nicholls, JOM, 2000, vol. 52, pp. 28-35.10.1007/s11837-000-0112-2 ↗
2. A.G. Evans, D.R. Mumm, J.W. Hutchinson, G.H. Meier and F.S. Pettit, Prog. Mater. Sci., 2001, vol. 46, pp. 505-553.10.1016/S0079-6425(00)00020-7 ↗
3. C.U. Hardwicke and Y.-C. Lau, J. Therm. Spray Technol., 2013, vol. 22, pp. 564-576.10.1007/s11666-013-9904-0 ↗
4. H. Chen and T.H. Hyde, Mater. Sci. Eng. A, 2017, vol. 680, pp. 203-209.10.1016/j.msea.2016.10.097 ↗
5. S. Li, X. Yang, H. Qi, G. Xu and D. Shi, Mater. Sci. Eng. A, 2016, vol. 678, pp. 57-64.10.1016/j.msea.2016.09.064 ↗
6. T. Sadowski and P. Golewski, Comput. Mater. Sci., 2012, vol. 64, pp. 285-288.10.1016/j.commatsci.2012.02.048 ↗
7. H. Chen, G.A. Jackson and W. Sun, J. Therm. Spray Technol., 2017, vol. 26, pp. 1222-1238.10.1007/s11666-017-0593-y ↗
8. H. Chen and T. Barman, Comput. Mater. Sci., 2018, vol. 147, pp. 103-14.10.1016/j.commatsci.2018.02.013 ↗
9. A. Gil, V. Shemet, R. Vassen, M. Subanovic, J. Toscano, D. Naumenko, L. Singheiser and W.J. Quadakkers, Surf. Coat. Technol., 2006, vol. 201, pp. 3824-3828.10.1016/j.surfcoat.2006.07.252 ↗
10. X. Yang, S. Li and H. Qi, Int. J. Fatigue, 2015, vol. 75, pp. 126-134.10.1016/j.ijfatigue.2015.02.018 ↗
11. H. Chen, T.H. Hyde, K.T. Voisey and D.G. McCartney, Mater. Sci. Eng. A, 2013, vol. 585, pp. 205-13.10.1016/j.msea.2013.06.080 ↗
12. X. Gong, H. Peng, Y. Ma, H. Guo and S. Gong, J. Alloys Compd., 2016, vol. 672, pp. 36-44.10.1016/j.jallcom.2016.02.115 ↗
13. H. Chen: Ph.D. Thesis, University of Nottingham, 2015.
14. H. Chen, T.H. Hyde, K.T. Voisey and D.G. McCartney, Proc. IMechE Part L: J. Mater.: Des. Appl., 2018, vol. 232, pp. 242–49.
15. M. Tahari, M. shamanian and M. salehi, J. Alloys Compd., 2015, vol. 646, pp. 372-379.10.1016/j.jallcom.2015.06.020 ↗
16. P. Puetz, X. Huang, R.S. Lima, Q. Yang and L. Zhao, Surf. Coat. Technol., 2010, vol. 205, pp. 647-657.10.1016/j.surfcoat.2010.07.079 ↗
17. T. Mori, S. Kuroda, H. Murakami, H. Katanoda, Y. Sakamoto and S. Newman, Surf. Coat. Technol., 2013, vol. 221, pp. 59-69.10.1016/j.surfcoat.2013.01.028 ↗
18. R.D. Jackson, M.P. Taylor, H.E. Evans and X.-H. Li, Oxid. Met., 2011, vol. 76, pp. 259-271.10.1007/s11085-011-9253-7 ↗
19. H. Chen, Mater. Charact., 2018, vol. 136, pp. 444-451.10.1016/j.matchar.2017.09.020 ↗
20. P. Poza and P.S. Grant, Surf. Coat. Technol., 2006, vol. 201, pp. 2887-2896.10.1016/j.surfcoat.2006.06.001 ↗
21. D. Naumenko, V. Shemet, L. Singheiser and W. Quadakkers, J. Mater. Sci., 2009, vol. 44, pp. 1687-1703.10.1007/s10853-009-3284-3 ↗
22. T. Koomparkping, S. Damrongrat and P. Niranatlumpong, J. Therm. Spray Technol., 2005, vol. 14, pp. 264-267.10.1361/10599630523845 ↗
23. D.R.G. Achar, R. Munoz-Arroyo, L. Singheiser and W.J. Quadakkers, Surf. Coat. Technol., 2004, vol. 187, pp. 272-283.10.1016/j.surfcoat.2004.02.018 ↗
24. Y.Z. Liu, X.B. Hu, S.J. Zheng, Y.L. Zhu, H. Wei and X.L. Ma, Mater. Des., 2015, vol. 80, pp. 63-69.10.1016/j.matdes.2015.05.014 ↗
25. M. Elsaß, M. Frommherz, A. Scholz and M. Oechsner, Surf. Coat. Technol., 2016, vol. 307, pp. 565-573.10.1016/j.surfcoat.2016.09.049 ↗
26. R.A. Mahesh, R. Jayaganthan and S. Prakash, J. Alloys Compd., 2009, vol. 468, pp. 392-405.10.1016/j.jallcom.2008.01.025 ↗
27. H. Peng, H. Guo, J. He and S. Gong, J. Alloys Compd., 2010, vol. 502, pp. 411-416.10.1016/j.jallcom.2010.04.183 ↗
28. H.E. Evans and M.P. Taylor, Oxid. Met., 2001, vol. 55, pp. 17-34.10.1023/A:1010369024142 ↗
29. J. Reinoso, M. Paggi and R. Rolfes, Comput. Mater. Sci., 2016, vol. 116, pp. 82-95.10.1016/j.commatsci.2015.08.031 ↗
30. M. Bäker, Comput. Mater. Sci., 2012, vol. 64, pp. 79-83.10.1016/j.commatsci.2012.02.044 ↗
31. P. Seiler, M. Bäker and J. Rösler, Comput. Mater. Sci., 2013, vol. 80, pp. 27-34.10.1016/j.commatsci.2013.04.028 ↗
32. C. Bumgardner, B. Croom and X. Li, Acta Mater., 2017, vol. 128, pp. 54-63.10.1016/j.actamat.2017.01.061 ↗
33. E.Y. Lee, D.M. Chartier, R.R. Biederman and R.D. Sisson, Surf. Coat. Technol., 1987, vol. 32, pp. 19-39.10.1016/0257-8972(87)90095-8 ↗
34. S.M. Meier, D.M. Nissley, and K.D. Sheffler: Report No. 18911/NAS3-23944, Lewis Research Center, 1991.
35. J.A. Nesbitt: Report No. NASA/TM-2000-209271, Glenn Research Center, 2000.
36. M.S.A. Karunaratne, S.L. Ogden, S.D. Kenny and R.C. Thomson, Mater. Sci. Technol., 2009, vol. 25, pp. 287-299.10.1179/174328408X355415 ↗
37. M.S.A. Karunaratne, I. Di Martino, S.L. Ogden, D.L. Oates and R.C. Thomson, Metall. Mater. Trans. A, 2011, vol. 43, pp. 774-788.
38. R. Eriksson, K. Yuan, X.-H. Li, and R. LinPeng: Surf. Coat. Technol., 2014, vol. 253, pp. 27-37.10.1016/j.surfcoat.2014.05.010 ↗
39. R. Pillai, W.G. Sloof, A. Chyrkin, L. Singheiser and W.J. Quadakkers, Mater. High Temp., 2015, vol. 32, pp. 57-67.10.1179/0960340914Z.00000000063 ↗
40. K. Yuan, R. Lin Peng, X.-H. Li, S. Johansson and Y.-D. Wang, Surf. Coat. Technol., 2015, vol. 261, pp. 86-101.10.1016/j.surfcoat.2014.11.053 ↗
41. H. Chen, G.A. Jackson, K.T. Voisey and D.G. McCartney, Surf. Coat. Technol., 2016, vol. 291, pp. 34-42.10.1016/j.surfcoat.2016.02.008 ↗
42. L. Wang, D.C. Li, J.S. Yang, F. Shao, X.H. Zhong, H.Y. Zhao, K. Yang, S.Y. Tao and Y. Wang, J. Eur. Ceram. Soc., 2016, vol. 36, pp. 1313-1331.10.1016/j.jeurceramsoc.2015.12.038 ↗
43. H. Chen and D.G. McCartney, Surf. Coat. Technol., 2017, vol. 313, pp. 107-114.10.1016/j.surfcoat.2017.01.075 ↗
44. B.-Y. Zhang, G.-J. Yang, C.-X. Li and C.-J. Li, Appl. Surf. Sci., 2017, vol. 406, pp. 99-109.10.1016/j.apsusc.2017.02.123 ↗
45. D. Seo, K. Ogawa, Y. Suzuki, K. Ichimura, T. Shoji and S. Murata, Appl. Surf. Sci., 2008, vol. 255, pp. 2581-2590.10.1016/j.apsusc.2008.07.141 ↗
46. C. Wagner, J. Electrochem. Soc., 1952, vol. 99, pp. 369-380.10.1149/1.2779605 ↗
47. G. Wahl, Thin Solid Films, 1983, vol. 107, pp. 417-426.10.1016/0040-6090(83)90303-6 ↗
48. F. Gesmundo and B. Gleeson, Oxid. Met., 1995, vol. 44, pp. 211-237.10.1007/BF01046728 ↗
49. P. Carter, B. Gleeson and D.J. Young, Acta Mater., 1996, vol. 44, pp. 4033-4038.10.1016/S1359-6454(96)00054-7 ↗
50. H. Chen, Y.Q. Si and D.G. McCartney, J. Alloys Compd., 2017, vol. 704, pp. 359-365.10.1016/j.jallcom.2017.02.002 ↗
51. S. Saeidi, K.T. Voisey and D.G. McCartney, J. Therm. Spray Technol., 2011, vol. 20, pp. 1231–1243.10.1007/s11666-011-9666-5 ↗
52. S. Saeidi, K.T. Voisey and D.G. McCartney, J. Therm. Spray Technol., 2009, vol. 18, pp. 209-216.10.1007/s11666-009-9311-8 ↗
53. D. Salehi Doolabi, M.R. Rahimipour, M. Alizadeh, S. Pouladi, S.M.M. Hadavi and M.R. Vaezi, Vacuum, 2017, vol. 135, pp. 22-33.10.1016/j.vacuum.2016.10.014 ↗
54. C.A. Schneider, W.S. Rasband and K.W. Eliceiri, Nat. Methods, 2012, vol. 9, pp. 671-675.10.1038/nmeth.2089 ↗
55. L. Lelait, S. Alpérine and R. Mévrel, J. Mater. Sci., 1992, vol. 27, pp. 5-12.10.1007/BF02403637 ↗
56. A. Paul, A.A. Kodentsov and F.J.J. van Loo, J. Alloys Compd., 2005, vol. 403, pp. 147-153.10.1016/j.jallcom.2005.04.194 ↗
57. A.J. Campbell, L. Danielson, K. Righter, C.T. Seagle, Y. Wang and V.B. Prakapenka, Earth. Planet. Sci. Lett., 2009, vol. 286, pp. 556-564.10.1016/j.epsl.2009.07.022 ↗
58. A. Borgenstam, L. Höglund, J. Ågren and A. Engström, J. Phase Equilib., 2000, vol. 21, pp. 269-280.10.1361/105497100770340057 ↗
59. J.O. Andersson, T. Helander, L. Höglund, P. Shi and B. Sundman, Calphad, 2002, vol. 26, pp. 273-312.10.1016/S0364-5916(02)00037-8 ↗
60. N. Saunders: Superalloys 1996, TMS, Warrendale, PA, 1996, p. 101.10.7449/1996/Superalloys_1996_101_110 ↗
61. L.M. Cheng, E.B. Hawbolt and T.R. Meadowcroft, Metall. Mater. Trans. A, 2000, vol. 31, pp. 1907-1916.10.1007/s11661-000-0218-8 ↗
62. P. Krukovsky, V. Kolarik, K. Tadlya, A. Rybnikov, I. Kryukov, N. Mojaiskaya and M. Juez-Lorenzo, Surf. Coat. Technol., 2004, vol. 177-178, pp. 32-36.10.1016/j.surfcoat.2003.06.002 ↗
63. T.J. Nijdam and W.G. Sloof, Acta Mater., 2008, vol. 56, pp. 4972-4983.10.1016/j.actamat.2008.06.010 ↗
64. Y.H. Sohn, J.H. Kim, E.H. Jordan and M. Gell, Surf. Coat. Technol., 2001, vol. 146-147, pp. 70-78.10.1016/S0257-8972(01)01478-5 ↗
65. H. Chen, D.G. McCartney and K.T. Voisey, Mater. High Temp., 2015, vol. 32, pp. 215-220.10.1179/0960340914Z.000000000103 ↗
66. P. Niranatlumpong, C.B. Ponton and H.E. Evans, Oxid. Met., 2000, vol. 53, pp. 241-258.10.1023/A:1004549219013 ↗
67. F.J. Belzunce, V. Higuera and S. Poveda, Mater. Sci. Eng. A, 2001, vol. 297, pp. 162-167.10.1016/S0921-5093(00)01239-9 ↗
68. F. Gesmundo, F. Viani and Y. Niu, Oxid. Met., 1996, vol. 45, pp. 51-76.10.1007/BF01046820 ↗
69. X. Li, N. Saunders and A.P. Miodownik, Metall. Mater. Trans. A, 2002, vol. 33, pp. 3367-3373.10.1007/s11661-002-0325-9 ↗