Microstructure, Texture, and Mechanical Behavior of As-cast Ni-Fe-W Matrix Alloy
Source abstract
Abstract
This article describes the tensile properties, flow, and work-hardening behavior of an experimental alloy 53Ni-29Fe-18W in as-cast condition. The microstructure of the alloy 53Ni-29Fe-18W displays single phase (fcc) in as-cast condition along with typical dendritic features. The bulk texture of the as-cast alloy reveals the triclinic sample symmetry and characteristic nature of coarse-grained materials. The alloy exhibits maximum strength (σYS and σUTS) values along the transverse direction. The elongation values are maximum and minimum along the transverse and longitudinal directions, respectively. Tensile fracture surfaces of both the longitudinal and transverse samples display complete ductile fracture features. Two types of slip lines, namely, planar and intersecting, are observed in deformed specimens and the density of slip lines increases with increasing the amount of deformation. The alloy displays moderate in-plane anisotropy (AIP) and reasonably low anisotropic index (δ) values, respectively. The instantaneous or work-hardening rate curves portray three typical stages (I through III) along both the longitudinal and transverse directions. The alloy exhibits dislocation-controlled strain hardening during tensile testing, and slip is the predominant deformation mechanism.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Metal Alloys Wear and Properties · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. E.F. Bradley: Superalloys: A Technical Guide, ASM International, Materials Park, OH, 1988.
2. C.T. Sims: Superalloy II, Wiley, New York, NY, 1987.
3. M.J. Donachie: Superalloys, ASM International, Materials Park, OH, 1984.
4. J. Lu, E.S. Choi, and H.D. Zhou: J. Appl. Phys., 2008, vol. 103, pp. 64908–64913.10.1063/1.2899058 ↗
5. K.K. Mehta, P. Mukhopadhyay, R.K. Mandal, and A.K. Singh: Metall. Mater. Trans. A, 2014, vol. 45A, pp. 3493–350410.1007/s11661-014-2294-1 ↗
6. K.K. Mehta, P. Mukhopadhyay, R.K. Mandal, and A.K. Singh: Mater. Charact., 2015, vol. 110, pp. 175–91.10.1016/j.matchar.2015.10.011 ↗
7. A. Upadhyaya: Mater. Chem. Phys., 2001, vol. 67, pp. 101–10.10.1016/S0254-0584(00)00426-0 ↗
8. H.J. Ryu, S.H. Hong, and W.H. Baek: Mater. Sci. Eng. A, 2000, vol. 291, pp. 91–96.10.1016/S0921-5093(00)00968-0 ↗
9. R.M. German: Liquid Phase Sintering, Plenum Press, Rensselaer Polytechnic Institute, Troy, NY, 1985, p. 228.10.1007/978-1-4899-3599-1 ↗
10. L. Delehouzee and A. Deruyttere: Acta Metall., 1967, vol. 15, pp. 727–34.10.1016/0001-6160(67)90353-7 ↗
11. C.C. Fu, L.J. Chang, Y.C. Huang, P.W. Wong, and J.S.C. Jang: Adv. Mater. Res., 2007, vols. 15–17, pp. 575–80.10.4028/www.scientific.net/AMR.15-17.575 ↗
12. R. Bollina and R.M. German: Int. J. Refract. Met. Hard Mater., 2004, vol. 22, pp 117–27.10.1016/j.ijrmhm.2004.01.006 ↗
13. Chun-Liang Chen and Chun-Lin Huang: Intermetallics, 2013, vol. 41, pp. 10–15.10.1016/j.intermet.2013.04.014 ↗
14. N. Senthilnathan, A.A. Raja, and G. Venktachalam: Trans. IIM, 2017, vol. 70, pp. 1161–76.
15. R.M. German, L.L. Bourguignon, and B.H. Rabin: J. Met., 1985, vol. 37, pp. 36–39.
16. P. Stuitje, R. Harkema, and C. Taal: U.S. Patent No. 5462576, 1995.
17. M. Kaczorowski, P. Skoczylas, A. Krzynska, and J. Kaniewski: Arch. Foundry Eng., 2012, vol. 12, pp. 75–80.10.2478/v10266-012-0110-1 ↗
18. J. Das, G. Appa Rao, and S.K. Pabi: Mater. Sci. Eng. A, 2010, vol. 527, pp. 7841–47.10.1016/j.msea.2010.08.071 ↗
19. R. Cury, F. Issartel, J.M. Joubert, and H. Couque: Powder Metall., 2013, vol. 56, pp. 347–50.10.1179/0032589913Z.000000000137 ↗
20. F. Akhtar: Adv. Mater. Res., 2007, vols. 26–28, pp. 1055–58.10.4028/www.scientific.net/AMR.26-28.1055 ↗
21. M. Erol, M. Erdogan, and I. Kakrkaya: 18th Int. Metall. Mater. Congr. (IMMC-2016), September 29–October 1, 2016.
22. C.L. Chen, Y. Zeng, and J.G. Lee: Acta Physica Polonica A, 2014, vol. 126, pp. 907–11.10.12693/APhysPolA.126.907 ↗
23. S.G. Caldwell: WM2013 Conf., Phoenix, AZ, February 24–28, 2013, pp. 1–18.
24. A. Mondal, D. Agrawal, and A. Upadhyaya: J. Microwave Power Electromagn. Energy, 2010, vol. 44, pp. 28–44.10.1080/08327823.2010.11689768 ↗
25. H. Elshimy, Z.K. Heiba, and Karimat El-Sayed: Adv. Mater. Phys. Chem., 2014, vol. 4, pp. 237–57.10.4236/ampc.2014.412027 ↗
26. R. Osama, A.S. Abdalla, W.M. Elthalabawy, G.M. Abdo, and M.T. Sallam: Int. J. Res. Eng. Technol., 2016, vol. 5, pp. 313–16.
27. L.G. Schultz: J. Appl. Phys., 1949, vol. 20, pp. 1030–33.10.1063/1.1698268 ↗
28. A. Sambasiva Rao, M.K. Mohan, and A.K. Singh: Int. J. Mater. Res., 2018 (accepted).
29. M. Yousuf, P.C. Sahu, H.K. Jajoo, S. Rajagopalan, and K. Govind Rajan: J. Phys. F. Met. Phys., 1986, vol. 16, p. 373.10.1088/0305-4608/16/3/015 ↗
30. K. Saeidi, X. Gao, Y. Zhong, and Z.J. Shen: Mater. Sci. Eng. A, 2015, vol. 625, pp. 221–29.10.1016/j.msea.2014.12.018 ↗
31. K.E. Knipling, G. Zeman, J.S. Marte, S.M. Kelly, and S.L. Kampe: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 2821–28.10.1007/s11661-004-0229-y ↗
32. R.L. Woodward, I.G. McDonald, and A.J. Gunner: Mater. Sci. Lett., 1986, vol. 5, pp. 413–14.10.1007/BF01672345 ↗
33. K.V. Jata, A.K. Hopkins, and R.J. Rioja: Mater. Sci. Forum, 1996, vols. 217–222, pp. 647–52.10.4028/www.scientific.net/MSF.217-222.647 ↗
34. S. Banumathy, R.K. Mandal, and A.K. Singh: Int. J. Mater. Res., 2011, vol. 102, pp. 208–17.10.3139/146.110468 ↗
35. Y.T. Wu and C.H. Koo: Scripta Metall., 1998, vol. 38, pp. 267–71.10.1016/S1359-6462(97)00431-4 ↗
36. G.E. Dieter: Mechanical Metallurgy, 3rd ed., McGraw-Hill, New York, NY, 1988.
37. D.C. Ludwigson: Metall. Trans., 1971, vol. 2, pp. 2825–28.10.1007/BF02813258 ↗
38. P. Manda, U. Chakkingal, and A.K. Singh: Metall. Mater. Trans. A, 2016, vol. 47A, pp. 3447–63.10.1007/s11661-016-3508-5 ↗