journal article·2018-05Open access

Characterization of Loading Responses and Failure Loci of a Boron Steel Spot Weld

N. D. Raath, D. Norman, I. McGregor, S. Hepple, R. Dashwood, D. J. Hughes

Abstract

Abstract Boron steel, classed as an ultra high-strength steel (UHSS), has been utilized in anti-intrusion systems in automobiles, providing high strength and weight-saving potential through gage reduction. UHSS spot welds exhibit unique hardness distributions, with a hard nugget and outlying base material, but with a soft heat-affected zone in-between these regions. This soft zone reduces the strength of the weld and makes it susceptible to failure. Due to the interaction of various weld zones that occurs during loading, there is a need to characterize the loading response of the weld for accurate failure predictions. The loading response of certain weld zones, as well as failure loci, was obtained through physical simulation of the welding process. The results showed a significant difference in mechanical behavior through the weld length. An important result is that instrumented indentation was shown to be a valid, quantitative method for verifying the accuracy with which weld microstructure has been recreated with regard to the target weld microstructure.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. R. Mohan Iyengar, B. Fedewa, Y.W. Wang, D.F. Maatz Jr., and R.L. Hughes: SAE Int., 2008, pp 1–14.
2. 2. Yu, Y., C. Wang, S. Chen and Z. Lu, Adv. Mater. Res., 2011. 339: pp 375-78.10.4028/www.scientific.net/AMR.339.375 ↗
3. 3. Choi, H.S., G.H. Park, W.S. Lim and B.M. Kim, J. Mech. Sci. Technol., 2011. 25: pp 1543-50.10.1007/s12206-011-0408-x ↗
4. 4. Kong, J.P., T.K. Han, K.G. Chin, B.G. Park and C.Y. Kang, Mater. Des., 2013. 54(1): pp 598-609.
5. 5. Sommer, S., IOP Conf. Series: Materials Science and Engineering, 2010. 10(1): pp 1-10.
6. T. Lienert, T. Siewert, S. Babu, and V. Acoff: ASM Handbook Volume 6A Welding Fundamentals and Processes, ASM International, 2011.10.31399/asm.hb.v06a.9781627081740 ↗
7. 7. Furuhara, T., K. Kobayashi and T. Maki, ISIJ Int., 2004. 44(11): pp 1937 - 44.10.2355/isijinternational.44.1937 ↗
8. R. Blondeau: Metallurgy and Mechanics of Welding. Wiley: London (2013).
9. 9. Liang, X., X. Yuan, H. Wang, X. Li, C. Li and X. Pan, Int. J. Precis. Eng. Manuf., 2016. 17(12): pp 1659 - 64.10.1007/s12541-016-0192-8 ↗
10. 10. Matya, M. and X.Q. Gayden, Weld. J., 2005. 84(11): pp 172-82.
11. 11. Ma, C., D.L. Chen, S.D. Bhole, G. Boudreau, A. Lee and E. Biro, Mater. Sci. Eng. A, 2008. 485(1): pp 334 - 46.10.1016/j.msea.2007.08.010 ↗
12. 12. Farabi, N., D.L. Chen, J. Li, Y. Zhou and S.J. Dong, Mater. Sci. Eng. A, 2010. 527(4): pp 1215 - 22.10.1016/j.msea.2009.09.051 ↗
13. 13. O’Keeffe, C., J. Imbert-Boyd, M. Worswick, C. Butcher, S. Malcolm, J. Dykeman, P. Penner, C. Yau, R. Soldaat, and W. Bernert, Procedia Eng., 2017. 197(1): pp 294 - 303.10.1016/j.proeng.2017.08.107 ↗
14. Dynamic Systems Inc. Gleeble. 2015 [cited 2015 23/10/2015]; www.gleeble.com.
15. 15. Abspoel, M., B.M. Neelis and P. van Liempt, J. Mater. Process. Technol., 2016. 228(1): pp 34 - 42.10.1016/j.jmatprotec.2015.05.007 ↗
16. 16. Eller, T.K., L. Greve, M.T. Andres, M. Medricky, H.J.M. Geijselaers, V.T. Meinders and A.H. van den Boogaard, J. Mater. Process. Technol., 2016. 234(1): pp 309-22.10.1016/j.jmatprotec.2016.03.026 ↗
17. 17. Ye, D., F. Mi, J. Liu, Y. Xu, Y. Chen and L. Xiao, J. Mater. Sci. Eng. A, 2013. 564(1): pp 76 - 84.10.1016/j.msea.2012.11.077 ↗
18. 18. Chung, K.H., W. Lee, J.H. Kim, C. Kim, S.H. Park, D. Kwon and K. Chung, Int. J. Solids Struct., 2009. 46(2): pp 344 - 63.10.1016/j.ijsolstr.2008.08.041 ↗
19. 19. Sun, G., F. Xu, G. Li, X. Huang and Q. Li, Comput. Mater. Sci., 2014. 85(1): pp 347 - 62.10.1016/j.commatsci.2014.01.006 ↗
20. 20. Dao, M., N. Chollacoop, K.J. van Vliet, T.A. Venkatesh and S. Suresh, Acta Mater., 2001. 49(19): pp 3899-918.10.1016/S1359-6454(01)00295-6 ↗
21. 21. Lee, J., C. Lee and B. Kim, Mater. Des., 2009. 30(9): pp 3395 - 404.10.1016/j.matdes.2009.03.030 ↗
22. 22. Kim, J.J., T.H. Pham and S.E. Kim, Int. J. Mech. Sci., 2015. 1(103): pp 265 - 74.10.1016/j.ijmecsci.2015.09.015 ↗
23. 23. Atrian, A., G.H. Majzoobi, S.H. Nourbakhsh, S.A. Galehdari and R.M. Nejad, Adv. Powder Technol., 2016. 27(4): pp 1821 - 27.10.1016/j.apt.2016.06.015 ↗
24. 24. Pham, T.H. and S.E. Kim, Constr. Build. Mater., 2017. 155(1): pp 176 - 86.10.1016/j.conbuildmat.2017.08.033 ↗
25. 25. De Bono, D.M., T. London, M. Baker and M.J. Whiting, Int J Mech Sci, 2017. 123(1): pp 162 - 76.10.1016/j.ijmecsci.2017.02.006 ↗
26. 26. Cheng, Y.T. and C.M. Cheng, J. Mater. Res., 1999. 14(9): pp 3493 - 96.10.1557/JMR.1999.0472 ↗
27. 27. Oliver, W.C. and G.M. Pharr, J Mater Res, 2004. 19(1): pp 3 - 20.10.1557/jmr.2004.19.1.3 ↗
28. 28. Oliver, W.C. and G.M. Pharr, J Mater Res, 1992. 7(6): pp 1564 - 83.10.1557/JMR.1992.1564 ↗
29. H. Lanzerath, A. Bach, G. Oberhofer, and H. Gese: SAE Int., 2007, pp 1–10.
30. 30. Avramovic-Cingara, G., Y. Ososkov, M.K. Jain and D.S. Wilkinson, Mater. Sci. Eng., 2009. 516(1): pp 7-16.10.1016/j.msea.2009.03.055 ↗
31. 31. Mohr, D. and F. Ebnoether, Int. J. Solids Struct., 2009. 46: pp 3535-47.10.1016/j.ijsolstr.2009.05.011 ↗
32. Institute, B.S., BS EN ISO 10447:2007. British Standards, 2007.
33. 33. den Uijl, N., T. Okada, T. Moolevliet, A. Mennes, E. van den Aa, M. Uchihara, S. Smith, H. Nishibata, T. van der Veldt, and K. Fukui, Weld. World, 2012. 56(8): pp 51-63.10.1007/BF03321365 ↗
34. Institute, B.S., BS EN ISO 6507-1:1998 Metallic materials - Vickers hardness test British Standards, 1998.
35. SORPAS User Manual 7.0. 2007: SWANTEC Software and Engineering ApS.
36. A. Sayles: Tata Steel Test Report Number 11KT1037. 2011, Tata Steel.
37. Institute, B.S., BS EN ISO 6507-1:1998. British Standards, 1998.
38. 38. Prime, M.B., T. Gnaupel-Herold, J.A. Baumann, R.J. Lederich, D.M. Bowden and R.J. Sebring, Acta Mater., 2006. 54(15): pp 4013-21.10.1016/j.actamat.2006.04.034 ↗
39. R.A. Beaumont: Determining the Effect of Strain Rate on the Fracture of Sheet Steel. Ph.D. Thesis, University of Warwick, 2012.
40. 40. Bao, Y. and T. Wierzbicki, Int J Mech Sci, 2004. 46(1): pp 81 - 98.10.1016/j.ijmecsci.2004.02.006 ↗
41. N.D. Raath: Ph.D. Thesis, University of Warwick, 2014.
42. A.C. Fischer-Cripps: Nanoindentation. Springer, Berlin, 2011.10.1007/978-1-4419-9872-9 ↗
43. 43. Barcellona, A. and D. Palmeri, Metall. Mater. Trans. A, 2009. 40(5): pp 1160-74.10.1007/s11661-009-9790-8 ↗
44. 44. Lucas, B.N. and W.C. Oliver, Metall. Mater. Trans. A, 1999. 30(3): pp 601 - 10.10.1007/s11661-999-0051-7 ↗
45. G. Aggag and A. Abu-Elezz: in XVIII IMEKO Worl Congress, Rio de Janeiro, 2006.