Effect of Temperature and Composition on NiAl Precipitation and Morphology in Fe-Ni-Al Alloys
Source abstract
Abstract
NiAl-strengthened ferritic alloys have been of particular interest because of their possibilities as a high-temperature material for power-generation purposes. In the present work, the effect of temperature and composition on the precipitation of the NiAl (β′) phase was studied using a diffusion couple made of alloys Fe0.50Ni0.25Al0.25 and Fe0.80Ni0.08Al0.12. The composition gradient was obtained with a diffusion annealing treatment at 1373 K (1100°C), and the precipitation was promoted by aging at 1123 K, 1173 K and 1223 K (850 °C, 900 °C and 950 °C) for 5 hours. The formation of a supersaturated solid solution and the precipitation of the β′ phase were obtained after the diffusion annealing and aging treatments, respectively. A gradual increase in the size and volumetric fraction of the precipitates was evident in compositions with higher NiAl. This promoted changes in the precipitate morphology that followed the sequence: rounded cuboids → plates → irregular (maze-like). Compositions with a low β′ volumetric fraction followed the predicted size distributions of the Lifshitz-Slyozov-Wagner (LSW) theory. Finally, it was observed that the hardness tends to increase inversely to the Fe content and decreases only because of precipitate coarsening. The achieved results provide new information regarding the dependency of the morphology of β′ precipitates with composition and temperature.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · High Temperature Alloys and Creep · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (52)
Show source-provided references
1. Z. Sun, C.H. Liebscher, S. Huang, Z. Teng, G. Song, G. Wang, M. Asta, M. Rawlings, M.E. Fine and P.K. Liaw: Scripta Mater., 2013, vol. 68, pp. 384–388.10.1016/j.scriptamat.2012.10.040 ↗
2. R. Viswanathan, J.F. Henry, J. Tanzosh, G. Stanko, J. Shingledecker, B. Vitalis and R. Purgert: J. Mater. Eng. Perform., 2005, vol. 14, pp. 281–292.10.1361/10599490524039 ↗
3. R. Viswanathan, K. Coleman and U. Rao: Int. J. Press. Vessel. Pip., 2006, vol. 83, pp. 778–783.10.1016/j.ijpvp.2006.08.006 ↗
4. RD. Noebe, RR. Bowman and MV. Nathal: Int. Mater. Rev., 1993, Vol. 38 No.4, 193–23210.1179/imr.1993.38.4.193 ↗
5. A. Taylor and N. J. Doyle: J. Appl. Crystallogr., 1972, vol. 5, pp. 201–209.10.1107/S0021889872009203 ↗
6. C. T. Liu and K. S. Kumar: JOM, 1993, vol. 45, pp. 38–44.10.1007/BF03223218 ↗
7. D.F. Lahrman, R.D. Field and R. Darolia, in High Temperature Ordered Intermetallic Alloys IV (edited by L. Johnson, J.O. Stiegler and D.P. Pope), MRS Proc., 1991, vol. 213, pp. 603.
8. A. J. Duncan, M. J. Kaufman, C. T. Liu and M. K. Miller: App. Surf. Sci., 1994, vol. 76/77, pp. 155–159.10.1016/0169-4332(94)90336-0 ↗
9. R. Kainuma, K. Ishida and T. Nishizawa: Metall. Trans. A, 1992, vol. 23A, pp. 1147-1153.10.1007/BF02665046 ↗
10. N. V. Nathal: Metall. Trans. A, 1987, vol. 18A, pp. 1961-1970.10.1007/BF02647026 ↗
11. M. E. Krug and D. C. Dunand: Acta Mater., 2011, vol. 59, pp. 5125–5134.10.1016/j.actamat.2011.04.044 ↗
12. D. A. Grose and G. S. Ansell: Metall. Trans. A, 1981, vol. 12, pp. 1631-1645.10.1007/BF02643569 ↗
13. Z. Guo and W. Sha: Intermet., 2002, vol. 10, pp. 945-950.10.1016/S0966-9795(02)00116-4 ↗
14. Z. K. Teng, C. T. Liu, G. Ghosh, P. K. Liaw and M. E. Fine: Intermet., 2010, vol. 18, pp. 1437-1443.10.1016/j.intermet.2010.03.026 ↗
15. A. J. Bradley, J. Iron Steel Inst., 1951, vol. 168(3), pp. 233–244.
16. C. Stallybrass, A. Schneider and G. Sauthoff: Intermet., 2005, vol. 13, pp. 1263–1268.10.1016/j.intermet.2004.07.048 ↗
17. S.M. Zhu, S.C. Tjong, and J.K.L. Lai: Acta Mater., 1998, vol. 46 (9), pp. 2969–2976.10.1016/S1359-6454(98)00022-6 ↗
18. E. Contreras-Piedras, H. J. Dorantes-Rosales, V. M. López-Hirata,F. Hernández-Santiago, J. L. González-Velázquez and F. I. López-Monrroy: Mat. Sci. Eng. A, 2012, vol. 558, pp. 366–370.10.1016/j.msea.2012.08.013 ↗
19. P. R. Munroe, M. George, I. Beker and F. E. Kennedy: Mat. Sci. Eng. A, 2002, vol. 325, pp. 1-8.10.1016/S0921-5093(01)01403-4 ↗
20. M.A. Muñoz-Morris and D.G. Morris: Mat. Sci. Eng. A, 2007, vol. 444, pp. 236–241.10.1016/j.msea.2006.08.082 ↗
21. M.A. Muñoz-Morris, I. Gutierrez-Urrutia and D.G. Morris: Int. J. Plast., 2009, vol. 25, pp. 1011–1023.10.1016/j.ijplas.2008.09.006 ↗
22. H.A. Calderon, G. Kostorz. Y.Y. Qu, H.J. Dorantes, J.J. Cruz and J.G. Cabanas-Moreno: Mater. Sci. Eng. A, 1997 vol. 238, pp. 13–22.10.1016/S0921-5093(98)80012-9 ↗
23. R. K. W. Marceau, C. Qiu, S. P. Ringer and C. R. Hutchinson: Mater. Sci. Eng. A, 2012, vol. 546, pp. 153-161.10.1016/j.msea.2012.03.043 ↗
24. A.A. Kodentsov, G. F. Bastin and F. J.J. van Loo, in Methods for Phase Diagram Determination (edited by Ji-Cheng Zhao), Elsevier Science, 2007, 1st Edition, pp. 222–24510.1016/B978-008044629-5/50006-9 ↗
25. Q. Zhang, Z. Chen, W. Zhong and J.C. Zhao: Scr. Mater., 2017, vol. 128, pp. 32–35.10.1016/j.scriptamat.2016.09.040 ↗
26. Q. Zhang and J.C. Zhao: J. Alloys Compd., 2014, vol. 604, pp. 142–150.10.1016/j.jallcom.2014.03.092 ↗
27. T. Miyazaki, S. Kobayashi and T. Koyama: Metall. Mater. Trans. A, 1999, vol. 30, pp. 2783–2789.10.1007/s11661-999-0115-8 ↗
28. T. Miyazaki, T. Koyama and S. Kobayashi: Metall. Mater. Trans. A, 1996, vol. 27, pp. 945–949.10.1007/BF02649762 ↗
29. T. Miyazaki: Prog. Mater. Sci., 2012, vol. 57, pp. 1010–1060.10.1016/j.pmatsci.2011.11.002 ↗
30. S. Kobayashi, Y. Tsukamoto, T. Takasugi, H. Chinen, T. Omori, K. Ishida and S. Zaefferer: Intermet., 2009, vol. 17, pp. 1085–1089.10.1016/j.intermet.2009.05.009 ↗
31. C.P. Heijwegen and G.D. Rieck: Metall. Trans., 1973, vol. 4, pp. 2159–2167.10.1007/BF02643282 ↗
32. F.J.J. van Loo and G.D. Rieck: Acta Metall., 1973, vol. 21 (1), pp. 61–71.10.1016/0001-6160(73)90220-4 ↗
33. D. A. Porter, K. E. Easterling and M. Y. Sherif: Phase transformations in metals and alloys, 3rd edition, CRC Press, Boca Raton, FL, 2009, pp. 87–95.
34. J.A. Nesbitt and R. W. Heckel: Metall. Trans. A., 1987, vol. 18A, pp. 2061–2073.10.1007/BF02647078 ↗
35. D. L. Anton and A. F. Giamei: Mater. Sci. Eng., 1985, vol. 76, pp. 173–180.10.1016/0025-5416(85)90091-6 ↗
36. R. Taillard, A. Pineau, and B.J. Thomas: Mater. Sci. Eng., 1982, vol. 54, pp. 209–21910.1016/0025-5416(82)90115-X ↗
37. J. E. Morral: Metall. Mater. Trans. A, 2012, vol. 43, pp. 3462–3470.10.1007/s11661-011-1026-z ↗
38. A. J. Ardell and R. B. Nicholson: J. Phys. Chem. Solids, 1966, vol. 27, pp. 1793–1804.10.1016/0022-3697(66)90110-7 ↗
39. P. Fratzl and O. Paris: Phase Transit., 1999, vol. 67, pp. 707–724.10.1080/01411599908224505 ↗
40. Y. H. Sohn, A. Puccio and M. A. Dayananda: Metall. Mater. Trans. A, 2005, vol. 36, pp. 2361–2370.10.1007/s11661-005-0108-1 ↗
41. M. Fahrmann, P. Fratzl, O. Paris, E. Fahrmann and W. C. Johnson: Acta Metall. Mater., 1995, vol. 43, pp. 1007–1022.10.1016/0956-7151(94)00337-H ↗
42. .V. Goerler, I. Lopez-Galilea, L. Mujica Roncery, O. Shchyglo, W. Theisen and I. Steinbach: Acta Mater., 2017, vol. 124, pp. 151–158.10.1016/j.actamat.2016.10.059 ↗
43. P. Caron, C. Ramusat and F. Diologent: Superalloys 2008 Proceedings, 2008, TMS, pp. 159–67.
44. I. M. Lifshitz and V. V. Slyozov: Zh. eksp. Fiz., 1958, vol. 35, pp. 479.
45. I. M. Lifshitz and V. V. Slyozov: J. Phys. Chem. Solids, 1961, vol. 19, pp. 35-50.10.1016/0022-3697(61)90054-3 ↗
46. C. Wagner: Z. Electrochem., 1961, vol. 65, pp. 581–591.
47. R. A. MacKay and M. V. Nathal: Acta Metall. Mater., 1990, Vol. 38 (6), pp. 993-1005.10.1016/0956-7151(90)90171-C ↗
48. H. Li, L. Zuo, X. Song, Y. Wang and G. Chen: Rare Metals, 2009, vol. 28 (2), pp. 197-201.10.1007/s12598-009-0039-x ↗
49. V. Vaithyanathan and L.Q. Chen: Acta Mater., 2002, vol. 50, pp. 4061-4073.10.1016/S1359-6454(02)00204-5 ↗
50. L. Ratke and P. W. Voorhees: Growth and Coarsening, Springer-Verlag Berlin Heidelberg, New York, USA, 2002, p. 145.10.1007/978-3-662-04884-9 ↗
51. K. Thornton, N. Akaiwa and P. W. Vorhees: Acta Mater., 2004, vol. 52, pp. 1365-1378.10.1016/j.actamat.2003.11.036 ↗
52. Z.K. Teng, C.T. Liu, G. Ghosh, P.K. Liaw and M.E. Fine: Intermet., 2010, vol. 18 pp. 1437-144310.1016/j.intermet.2010.03.026 ↗