High Cycle Fatigue Behavior of Shot-Peened Steels
Source abstract
Abstract
The uniaxial fully reversed (R = –1) long life fatigue behavior of four shot-peened engineering steels with approximately the same hardness was investigated. Shot-peening, air-cooled forged AISI 1141 and crackable AISI 1070 steels had little effect on their fatigue limits (+2.5 and –2.0 pct, respectively). In the case of a powder forged 0.5 pct C steel, an increase in the fatigue limit of 10.4 pct was observed, albeit with a large standard deviation. Shot-peening quench and tempered AISI 1151 steel decreased its fatigue limit 12.0 pct, as a result of cyclic softening. In general, the beneficial effects of shot-peening these smooth specimens were relatively small. Neither cyclic softening nor hardening occurred in the non–shot-peened steels cycled under the same conditions.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Surface Treatment and Residual Stress · Erosion and Abrasive Machining · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (18)
Show source-provided references
1. Z. Gu, S. Yang, S. Ku, Y. Zhao, and X. Dai: Int. J. Adv. Manuf. Tech., 2005, vol. 25, pp. 883–87.10.1007/s00170-003-2022-2 ↗
2. H. Guechichi and L. Castex: J. Mater. Process. Tech., 2006, vol. 172, pp. 381–87.10.1016/j.jmatprotec.2005.10.010 ↗
3. R. Fathallah, A. Laamouri, H. Sidhom, and C. Braham: Int. J. Fatigue, 2004, vol. 26, pp. 1053–67.10.1016/j.ijfatigue.2004.03.007 ↗
4. A.M. Eleiche, M.M. Megahed, and N.M. Abd-Allah: J. Mater. Process. Tech., 2001, vol. 113, pp. 502–08.10.1016/S0924-0136(01)00601-X ↗
5. J.E. Hoffmann, D. LÖhe, and E. Macherauch: International Conferences on Shot Peening (ICSP-3), Garmisch-Partenkirchen, Germany, 1987, pp. 631–38.
6. A. Plumtree: 12th Int. Conf. Fracture, Ottawa, Canada, 2009, pp. 1–7.
7. I.F. Pariente and M. Guagliano: Surf. Coating Tech., 2008, vol. 202, pp. 3072–80.10.1016/j.surfcoat.2007.11.015 ↗
8. M. Giagliano and L. Vergani: Eng. Fract. Mech., 2004, vol. 71, pp. 501–12.10.1016/S0013-7944(03)00017-1 ↗
9. J. Lindemann, C. Buque, and F. Appel: Acta Mater., 2006, vol. 54, pp. 1155–64.10.1016/j.actamat.2005.10.043 ↗
10. W. Cao: Ph.D. Dissertation, ENSAM, Paris, France, 1989.
11. M.A.S. Torres and H.J.C. Voorwald: Int. J. Fatigue, 2002, vol. 24, pp. 877–86.10.1016/S0142-1123(01)00205-5 ↗
12. W.Z. Zhuang and G.R. Halford: Int. J. Fatigue, 2001, vol. 23, pp. 31–37.10.1016/S0142-1123(01)00132-3 ↗
13. Y.K. Gao, X.B. Li, Q.X. Yang, and M. Yao: Mater. Lett., 2007, vol. 61, pp. 466–69.10.1016/j.matlet.2006.04.089 ↗
14. G.H. Farrahi, J.L. Lebrun, and D. Courtain: Fatig. Fract. Eng. Mater. Struct., 1995, vol. 18, pp. 211–20.10.1111/j.1460-2695.1995.tb00156.x ↗
15. X.P. Jiang, C.S. Man, M.J. Shepard, and T. Zhai (2007) Mater. Sci. Eng. 468-70: 137–43.10.1016/j.msea.2007.01.156 ↗
16. A. Afzali: Masters Thesis, University of Toledo, Toledo, OH, 2004.
17. A. Afzali and A. Fatemi: SAE SP 2004, 1837, pp. 191–202.
18. D. Eifler, D. Löhe, and B. Scholtes: Residual Stresses—Measurement, Calculation and Evaluation, DGM, Informationsgesellschaft Verlag, Oberursel, Germany, 1991, pp. 157–66.