Correlation of Delta-Ferrite with Tensile and Charpy Impact Properties of Austenitic Fe-23Mn-Al-C Steels
Source abstract
Abstract
The correlation of delta-ferrite with the tensile and Charpy impact properties of austenitic Fe-23Mn-Al-C steels with different Al and C contents for cryogenic applications was investigated in this study. Microstructural analysis showed that the two steels with duplex phases had banded or layered microstructures with relatively fine-grained austenite and coarse-grained delta-ferrite which increased with Al content and decreased with C content. The geometrically necessary dislocation density increased with the fraction of the delta-ferrite phase. The steel with the highest delta-ferrite fraction of 26.6 pct had the highest yield strength of 576 MPa, while that with the delta-ferrite phase of less than 10.0 pct exhibited a mixed deformation behavior comprising deformation twins and dislocation glide which contributed to the highest tensile strength of 802 MPa and total elongation of 43.6 pct owing to an increase in the work hardening rate. In contrast, the Charpy impact test results revealed that the steels with duplex phases of austenite and delta-ferrite exhibited ductile-to-brittle transition behavior, whereas the steel with single-phase austenite had a higher absorbed energy exceeding 100 J at − 196 °C. The delta-ferrite phase had no significant effect on the absorbed energy at room temperature, but it acted as the main site for the propagation of brittle cracks at cryogenic temperatures and thus decreased the low-temperature toughness.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (53)
Show source-provided references
1. [1]P. Mallick, N.K. Tewary, S.K. Ghosh and P.P. Chattopadhyay: Mater. Charact., 2017, vol. 133, pp. 77-86.10.1016/j.matchar.2017.09.027 ↗
2. [2]T.S. Byun, N. Hashimoto and K. Farrell: Acta Mater., 2004, vol. 52, pp. 3889–99.10.1016/j.actamat.2004.05.003 ↗
3. [3]J. Kim, S. Choi, D. Park and J. Lee: Mater. Des., 2015, vol. 65, pp. 914-22.10.1016/j.matdes.2014.09.085 ↗
4. [4]M.J. Jang, H. Kwak, Y.W. Lee, Y. Jeong, J. Choi, Y.H. Jo, W.M. Choi, H.J. Sung, E.Y. Yoon, S. Praveen, S. Lee, B.J. Lee, M.I.A.E. Aal and H.S. Kim: Met. Mater. Int., 2019, vol. 25, pp. 277-84.10.1007/s12540-018-0184-6 ↗
5. [5]S. Kumar, H.T. Kwon, K.H. Choi, J.H. Cho, W. Lim and I. Moon: Energy Policy, 2011, vol. 39, pp. 4097-104.10.1016/j.enpol.2011.03.067 ↗
6. E.D. Marquardt, J.P. Le, and R. Radebaugh: Cryogenic material properties database, in: R.G. Ross Jr. (Ed.), Cryocoolers 11, Kluwer Academic Publishers, 2002, pp. 681–87.10.1007/0-306-47112-4_84 ↗
7. [7]C.W. Marschall, R.F. Hehemann and A.R. Troiano: Trans. ASM, 1962, vol. 55, pp. 135–38.
8. [8]M. Choi, J. Lee, H. Nam, N. Kang, M. Kim and D. Cho: Met. Mater. Int., 2020, vol. 26, pp. 240-47.10.1007/s12540-019-00320-4 ↗
9. [9]Y. Tomota, M. Strum and J.W. Morris: Metall. Trans. A, 1991, vol. 18, pp. 1073-81.10.1007/BF02668556 ↗
10. [10]J. Lee, S.S. Sohn, S. Hong, B.C. Suh, S.K. Kim, B.J. Lee, N.J. Kim and S. Lee: Metall. Mater. Trans. A, 2014, vol. 45, pp. 5419-30.10.1007/s11661-014-2513-9 ↗
11. [11]S.S. Sohn, S. Hong, J. Lee, B.C. Suh, S.K. Kim, B.J. Lee, N.J. Kim and S. Lee: Acta Mater., 2015, vol. 100, pp. 39-52.10.1016/j.actamat.2015.08.027 ↗
12. [12]J.S. Kim, J.B. Jeon, J.E. Jung, K.K. Um and Y.W. Chang: Met. Mater. Int., 2014, vol. 20, pp. 41–47.10.1007/s12540-014-1010-4 ↗
13. [13]H. Kim, Y. Ha, K.H. Kwon, M. Kang, N.J. Kim and S. Lee: Acta Mater., 2015, vol. 27, pp. 332-43.10.1016/j.actamat.2014.11.027 ↗
14. [14]J.K. Hwang: Met. Mater. Int., 2020, vol. 26, pp. 603-16.10.1007/s12540-019-00363-7 ↗
15. D. Kim, G.H. Jang. T. Lee, and C.S. Lee: Met. Mater. Int., 2020, vol. 26, pp. 1741–48.10.1007/s12540-019-00514-w ↗
16. [16]S.I. Lee, S.Y. Lee, J. Han and B. Hwang: Mater. Sci. Eng. A, 2019, vol. 742, pp. 334-43.10.1016/j.msea.2018.10.107 ↗
17. [17]M. Ghasri-Khouzani and J.R. McDermid: Mater. Sci. Eng. A, 2015, vol. 621, pp. 118-27.10.1016/j.msea.2014.10.042 ↗
18. [18]S. Allain, J.P. Chateau and O. Bouaziz: Mater. Sci. Eng. A, 2004, vol. 387–389, pp. 143–47.10.1016/j.msea.2004.01.060 ↗
19. [19]L. Remy and A. Pineau: Mater. Sci. Eng. A, 1977, vol. 28, pp. 99–107.10.1016/0025-5416(77)90093-3 ↗
20. [20]Y.K. Lee and C. Choi: Metall. Mater. Trans. A, 2000, vol. 31, pp. 355–60.10.1007/s11661-000-0271-3 ↗
21. [21]S. Curtze and V.T. Kuokkala: Acta Mater., 2010, vol. 58, pp. 5129–41.10.1016/j.actamat.2010.05.049 ↗
22. [22]G.B. Olson and M. Cohen: Metall. Trans. A, 1976, vol. 7, pp. 1897–904.
23. [23]S. Curtze, V.T. Kuokkala, A. Oikari, J. Talonen and H. Hänninen: Acta Mater., 2011, vol. 59, pp. 1068–76.10.1016/j.actamat.2010.10.037 ↗
24. [24]S. Allain, J.P. Chateau, O. Bouaziz, S. Migot and N. Guelton: Mater. Sci. Eng. A, 2004, vol. 387, pp. 158–62.10.1016/j.msea.2004.01.059 ↗
25. [25]P.H. Adler, G.B. Olson and W.S. Owen: Metall. Mater. Trans. A, 1986, vol. 17, pp. 1725–37.10.1007/BF02817271 ↗
26. [26]I.A. Yakubtsov, A. Ariapour and D.D. Perovic: Acta Mater., 1999, vol. 47, pp. 1271–79.10.1016/S1359-6454(98)00419-4 ↗
27. [27]A. Dumay, J.P. Chateau, S. Allain, S. Migot and O. Bouaziz: Mater. Sci. Eng. A, 2008, vol. 483, pp. 184–87.10.1016/j.msea.2006.12.170 ↗
28. [28]P.J. Ferreira and P. Müllner: Acta Mater., 1998, vol. 46, pp. 4479–84.10.1016/S1359-6454(98)00155-4 ↗
29. [29]K. Ishida and T. Nishizawa: Trans. Jpn. Inst. Met., 1974, vol. 15, pp. 225–31.10.2320/matertrans1960.15.225 ↗
30. [30]J.E. Jung, J. Park, J.S. Kim, J.B. Jeon, S.K. Kim and Y.W. Chang: Met. Mater. Int., 2014, vol. 20, pp. 27–34.10.1007/s12540-014-1008-y ↗
31. [31]S.Y. Lee, S.I. Lee and B. Hwang: Mater. Sci. Eng. A, 2018, vol. 711, pp. 22-28.10.1016/j.msea.2017.10.074 ↗
32. [32]Y. Kwon, J.H. Hwang, H.C. Choi, T.T.T. Trang, B. Kim, A. Zargaran and N.J. Kim: Met. Mater. Int., 2020, vol. 26, pp. 75-82.10.1007/s12540-019-00314-2 ↗
33. [33]G. Frommeyer and U. Brüx: Steel Res. Int., 2006, vol. 77, pp. 627-33.10.1002/srin.200606440 ↗
34. [34]I. Gutierrez-Urrutia and D. Raabe: Acta Mater., 2012, vol. 60, pp. 5791-802.10.1016/j.actamat.2012.07.018 ↗
35. [35]S.S. Sohn, B.J. Lee, S. Lee, N.J. Kim and J.H. Kwak: Acta Mater., 2013, vol. 61, pp. 5050-66.10.1016/j.actamat.2013.04.038 ↗
36. [36]H. Kim, D.W. Suh and N.J. Kim: Sci. Technol. Adv. Mater., 2013, vol. 14, pp. 1-11.10.1088/1468-6996/14/1/014205 ↗
37. [37]S.H. Kim, H. Kim and N.J. Kim: Nature, 2015, vol. 518, pp. 77-79.10.1038/nature14144 ↗
38. [38]I. Gutierrez-Urrutia and D. Raabe: Mater. Sci. Technol., 2014, vol. 30, pp. 1099-104.10.1179/1743284714Y.0000000515 ↗
39. [39]B. Kim, S.J. Jeong, S.J. Park, J. Moon and C. Lee: Met. Mater. Int., 2019, vol. 25, pp. 1019-26.10.1007/s12540-019-00248-9 ↗
40. [40]S.W. Park, J.Y. Park, K.M. Cho, J.H. Jang, S.J. Park, J. Moon, T.H. Lee and J.H. Shin: Met. Mater. Int., 2019, vol. 25, pp. 683-96.10.1007/s12540-018-00230-x ↗
41. [41]M.J. Chae, A. Sharma, M.C. Oh, B. Ahn: Met. Mater. Int., 2021, vol. 27, pp. 629-38.10.1007/s12540-020-00823-5 ↗
42. [42]B. Fu, C. Pei, Y. Guo, L. Fu and A. Shan: Mater. Sci. Technol., 2020, vol. 36, pp. 827-34.10.1080/02670836.2020.1744247 ↗
43. [43]L. Fu, L. Fan, Z. Li, N. Sun, H. Wang, W. Wang and A. Shan: Mater. Sci. Eng. A, 2013, vol. 582, pp. 126-33.10.1016/j.msea.2013.05.087 ↗
44. [44]L. Fu, M. Shan, D. Zhang, H. Wang, W. Wang and A. Shan: Metall. Mater. Trans. A, 2017, vol. 48, pp. 2179-92.10.1007/s11661-017-3994-0 ↗
45. [45]L.P. Kubin and A. Mortensen: Scr. Mater., 2003, vol. 48, pp. 119-25.10.1016/S1359-6462(02)00335-4 ↗
46. [46]G.E. Dieter, Mechanical Metallurgy, 3rd ed., McGraw-Hill book co., New York, 1986.
47. [47]J.H. Shim, B. Hwang, M.G. Lee and J. Lee: Calphad, 2018, vol. 62, pp. 67-74.10.1016/j.calphad.2018.05.005 ↗
48. [48]S.I. Lee, J. Lee and B. Hwang: Mater. Sci. Eng. A, 2019, vol. 758, pp. 56-59.10.1016/j.msea.2019.04.113 ↗
49. [49]S.I. Lee, S.Y. Lee, S.G. Lee, H.G. Jung and B. Hwang: Met. Mater. Int., 2018, vol. 24, pp. 1221-31.10.1007/s12540-018-0173-9 ↗
50. [50]M.A. Meyers, O. Vöhringer and V.A. Lubarda: Acta Mater., 2001, vol. 49, pp. 4025–39.10.1016/S1359-6454(01)00300-7 ↗
51. [51]T.S. Byun: Acta Mater., 2003, vol. 51, pp. 3063–71.10.1016/S1359-6454(03)00117-4 ↗
52. [52]D.R. Steinmetz, T. Jäpel, B. Wietbrock, P. Eisenlohr, I. Gutierrez-Urrutia, A. Saeed-Akbari, T. Hickel, F. Roters and D. Raabe: Acta Mater., 2013, vol. 61, pp. 494–510.10.1016/j.actamat.2012.09.064 ↗
53. [53]N. Narita and J. Takamura: Philos. Mag., 1974, vol. 29, pp. 1001–28.10.1080/14786437408226586 ↗