Microstructure and Wear Behavior of High-Carbon Concentration CrCoNi Multi-principal Element Alloys
Source abstract
Abstract
CrCoNi multi-principal element alloys (MPEAs) have shown good strength-ductility combinations, but few other mechanical properties have been evaluated in these alloys so far. Although optimal wear-resistant alloys depend upon the intended application, a hard and tough material is often desirable. In this work, as-cast Cr40Co40Ni20 was tested for wear under dry-sliding conditions against an alumina pin, exhibiting good wear resistance and low coefficient of friction (CoF) of 0.12. To further improve the wear behavior, carbon (C) additions were evaluated in this alloy and in Cr40Co30Ni30, up to the liquid solubility limit at 1600 °C (~24 at. pct C). Alloy design was performed using computational thermodynamic calculations. Predicted microstructures contain: self-lubricating graphite flakes, hard primary Cr-rich carbides, and a tough eutectic matrix; in good agreement with experimental results. As-cast Cr40Co40Ni20-C, even without microstructural refinement, displayed low specific wear rate (on the order of 10−4 mm3/Nm) and moderate CoF (0.55-0.62). Its performance was hampered by the fracture and detachment of coarse primary carbides, which introduced an additional abrasive element into the tribosystem. These findings indicate that C additions to CrCoNi alloys, along with the refinement of primary carbides, represent a promising strategy to further improve the wear performance of MPEAs.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Entropy Alloys Studies · Advanced materials and composites · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (73)
Show source-provided references
1. 1 K. Holmberg and A. Erdemir: Friction, 2017, vol. 5, pp. 263–84.10.1007/s40544-017-0183-5 ↗
2. 2 J. Sugishita and S. Fujiyoshi: Wear, 1981, vol. 66, pp. 209–21.10.1016/0043-1648(81)90115-0 ↗
3. 3 J.R. Davis: ASM Specialty Handbook: Cast Irons, ASM international, United States of America, 1996.
4. 4 A. Zhang, J. Han, B. Su, P. Li, and J. Meng: Mater. Des., 2017, vol. 114, pp. 253–63.10.1016/j.matdes.2016.11.072 ↗
5. 5 S. Yadav, A. Kumar, and K. Biswas: Mater. Chem. Phys., 2018, vol. 210, pp. 222–32.10.1016/j.matchemphys.2017.06.020 ↗
6. 6 S. Yadav, S. Sarkar, A. Aggarwal, A. Kumar, and K. Biswas: Wear, 2018, vol. 410–411, pp. 93–109.10.1016/j.wear.2018.05.023 ↗
7. 7 A.S. Sharma, S. Yadav, K. Biswas, and B. Basu: Mater. Sci. Eng. R Reports, 2018, vol. 131, pp. 1–42.10.1016/j.mser.2018.04.003 ↗
8. P. Crook: in ASM Handbook Vol. 2: Properties and Selection: Nonferrous Alloys and Special- Purpose Materials, vol. 2, ASM International, 1990, pp. 446–54.10.31399/asm.hb.v02.a0001073 ↗
9. 9 X.H. Tang, R. Chung, C.J. Pang, D.Y. Li, B. Hinckley, and K. Dolman: Wear, 2011, vol. 271, pp. 1426–31.10.1016/j.wear.2010.11.047 ↗
10. 10 B. Cantor, I.T.H. Chang, P. Knight, and A.J.B. Vincent: Mater. Sci. Eng. A, 2004, vol. 375, pp. 213–8.10.1016/j.msea.2003.10.257 ↗
11. 11 J.W. Yeh, S.K. Chen, S.J. Lin, J.Y. Gan, T.S. Chin, T.T. Shun, C.H. Tsau, and S.Y. Chang: Adv. Eng. Mater., 2004, vol. 6, pp. 299–303.10.1002/adem.200300567 ↗
12. B. Gludovatz, A. Hohenwarter, D. Catoor, E.H. Chang, E.P. George, and R.O. Ritchie: Science, 2014, vol. 345, pp. 1153–8.10.1126/science.1254581 ↗
13. 13 B. Gludovatz, A. Hohenwarter, K.V.S. Thurston, H. Bei, Z. Wu, E.P. George, and R.O. Ritchie: Nat. Commun., 2016, vol. 7, pp. 1–8.10.1038/ncomms10602 ↗
14. 14 D.B. Miracle and O.N. Senkov: Acta Mater., 2017, vol. 122, pp. 448–511.10.1016/j.actamat.2016.08.081 ↗
15. 15 W. Zhang, P.K. Liaw, and Y. Zhang: Sci. China Mater., 2018, vol. 61, pp. 2–22.10.1007/s40843-017-9195-8 ↗
16. 16 E.P. George, D. Raabe, and R.O. Ritchie: Nat. Rev. Mater., 2019, vol. 4, pp. 515–34.10.1038/s41578-019-0121-4 ↗
17. 17 F.G. Coury, D. Santana, Y. Guo, J. Copley, L. Otani, S. Fonseca, G. Zepon, C. Kiminami, M. Kaufman, and A. Clarke: Scr. Mater., 2019, vol. 173, pp. 70–4.10.1016/j.scriptamat.2019.07.045 ↗
18. 18 F.G. Coury, P. Wilson, K.D. Clarke, M.J. Kaufman, and A.J. Clarke: Acta Mater., 2019, vol. 167, pp. 1–11.10.1016/j.actamat.2019.01.029 ↗
19. 19 F.G. Coury, K.D. Clarke, C.S. Kiminami, M.J. Kaufman, and A.J. Clarke: Sci. Rep., 2018, vol. 8, pp. 1–10.10.1038/s41598-018-26830-6 ↗
20. 20 R.O. Ritchie: Nat. Mater., 2011, vol. 10, pp. 817–22.10.1038/nmat3115 ↗
21. 21 Z. Wu, H. Bei, G.M. Pharr, and E.P. George: Acta Mater., 2014, vol. 81, pp. 428–41.10.1016/j.actamat.2014.08.026 ↗
22. 22 S. Yoshida, T. Bhattacharjee, Y. Bai, and N. Tsuji: Scr. Mater., 2017, vol. 134, pp. 33–6.10.1016/j.scriptamat.2017.02.042 ↗
23. 23 G. Laplanche, A. Kostka, C. Reinhart, J. Hunfeld, G. Eggeler, and E.P. George: Acta Mater., 2017, vol. 128, pp. 292–303.10.1016/j.actamat.2017.02.036 ↗
24. 24 S.F. Liu, Y. Wu, H.T. Wang, J.Y. He, J.B. Liu, C.X. Chen, X.J. Liu, H. Wang, and Z.P. Lu: Intermetallics, 2018, vol. 93, pp. 269–73.10.1016/j.intermet.2017.10.004 ↗
25. 25 K. Feng, Y. Zhang, Z. Li, C. Yao, L. Yao, and C. Fan: Surf. Coatings Technol., 2020, vol. 397, p. 126004.10.1016/j.surfcoat.2020.126004 ↗
26. 26 J. Miao, C.E. Slone, T.M. Smith, C. Niu, H. Bei, M. Ghazisaeidi, G.M. Pharr, and M.J. Mills: Acta Mater., 2017, vol. 132, pp. 35–48.10.1016/j.actamat.2017.04.033 ↗
27. 27 C. Niu, C.R. LaRosa, J. Miao, M.J. Mills, and M. Ghazisaeidi: Nat. Commun., 2018, vol. 9, pp. 1–9.10.1038/s41467-018-03846-0 ↗
28. 28 C.E. Slone, S. Chakraborty, J. Miao, E.P. George, M.J. Mills, and S.R. Niezgoda: Acta Mater., 2018, vol. 158, pp. 38–52.10.1016/j.actamat.2018.07.028 ↗
29. 29 Y.Y. Shang, Y. Wu, J.Y. He, X.Y. Zhu, S.F. Liu, H.L. Huang, K. An, Y. Chen, S.H. Jiang, H. Wang, X.J. Liu, and Z.P. Lu: Intermetallics, 2019, vol. 106, pp. 77–87.10.1016/j.intermet.2018.12.009 ↗
30. 30 P.A. Beaven, P.R. Swann, and D.R.F. West: J. Mater. Sci., 1979, vol. 14, pp. 354–64.10.1007/BF00589826 ↗
31. 31 Z. Wu, C.M. Parish, and H. Bei: J. Alloys Compd., 2015, vol. 647, pp. 815–22.10.1016/j.jallcom.2015.05.224 ↗
32. 32 N.D. Stepanov, N.Y. Yurchenko, M.A. Tikhonovsky, and G.A. Salishchev: J. Alloys Compd., 2016, vol. 687, pp. 59–71.10.1016/j.jallcom.2016.06.103 ↗
33. 33 J. Chen, Z. Yao, X. Wang, Y. Lu, X. Wang, Y. Liu, and X. Fan: Mater. Chem. Phys., 2018, vol. 210, pp. 136–45.10.1016/j.matchemphys.2017.08.011 ↗
34. 34 J. Peng, Z. Li, L. Fu, X. Ji, Z. Pang, and A. Shan: J. Alloys Compd., 2019, vol. 803, pp. 491–8.10.1016/j.jallcom.2019.06.204 ↗
35. 35 L. Guo, X. Ou, S. Ni, Y. Liu, and M. Song: Mater. Sci. Eng. A, 2019, vol. 746, pp. 356–62.10.1016/j.msea.2019.01.050 ↗
36. 36 I. Baker: Metals (Basel)., 2020, vol. 10, pp. 1–20.10.3390/met10050695 ↗
37. 37 J. Miao, T. Guo, J. Ren, A. Zhang, B. Su, and J. Meng: Vacuum, 2018, vol. 149, pp. 324–30.10.1016/j.vacuum.2018.01.012 ↗
38. 38 S. Pan, C. Zhao, P. Wei, and F. Ren: Wear, 2019, vol. 440–441, pp. 1–13.
39. 39 M. Chen, X.H. Shi, H. Yang, P.K. Liaw, M.C. Gao, J.A. Hawk, and J. Qiao: J. Mater. Res., 2018, vol. 33, pp. 3310–20.10.1557/jmr.2018.279 ↗
40. 40 J.M. Wu, S.J. Lin, J.W. Yeh, S.K. Chen, Y.S. Huang, and H.C. Chen: Wear, 2006, vol. 261, pp. 513–9.10.1016/j.wear.2005.12.008 ↗
41. 41 A. Ayyagari, C. Barthelemy, B. Gwalani, R. Banerjee, T.W. Scharf, and S. Mukherjee: Mater. Chem. Phys., 2018, vol. 210, pp. 162–9.10.1016/j.matchemphys.2017.07.031 ↗
42. 42 W. Lu, X. Luo, Y. Yang, J. Zhang, and B. Huang: Mater. Chem. Phys., 2019, vol. 238, p. 121841.10.1016/j.matchemphys.2019.121841 ↗
43. 43 H.U. Hong, B.S. Rho, and S.W. Nam: Mater. Sci. Eng. A, 2001, vol. 318, pp. 285–92.10.1016/S0921-5093(01)01254-0 ↗
44. 44 X. Wu, J. Xing, H. Fu, and X. Zhi: Mater. Sci. Eng. A, 2007, vol. 457, pp. 180–5.10.1016/j.msea.2006.12.006 ↗
45. 45 Y. Qu, J. Xing, X. Zhi, J. Peng, and H. Fu: Mater. Lett., 2008, vol. 62, pp. 3024–7.10.1016/j.matlet.2008.01.129 ↗
46. 46 X. Zhi, J. Liu, J. Xing, and S. Ma: Mater. Sci. Eng. A, 2014, vol. 603, pp. 98–103.10.1016/j.msea.2014.02.080 ↗
47. 47 H. Lv, R. Zhou, L. Li, H. Ni, J. Zhu, and T. Feng: Materials (Basel)., 2018, vol. 11, pp. 12–4.
48. Sterneland, T., Markström, A., Norgren, S., Aaune, R. E., & Seetharaman, S (2006) Metall. Mater. Trans. A, vol. 37A, pp. 3023–8.10.1007/s11661-006-0183-y ↗
49. B. Kaplan, A. Blomqvist, C. Århammar, M. Selleby, and S. Norgren: 18th Plansee Semin. 3–7 June, 2013 Reutte, Austria, 2013, vol. 3, p. HM104/1-HM104/12.
50. B. Kaplan, A. Markström, S. Norgren, and M. Selleby: Metall. Mater. Trans. A 2014, vol. 45, pp. 4820–8.10.1007/s11661-014-2441-8 ↗
51. 51 R.J. Chung, X. Tang, D.Y. Li, B. Hinckley, and K. Dolman: Wear, 2009, vol. 267, pp. 356–61.10.1016/j.wear.2008.12.061 ↗
52. 52 R.J. Chung, X. Tang, D.Y. Li, B. Hinckley, and K. Dolman: Wear, 2013, vol. 301, pp. 695–706.10.1016/j.wear.2013.01.079 ↗
53. 53 L.M. Du, L.W. Lan, S. Zhu, H.J. Yang, X.H. Shi, P.K. Liaw, and J.W. Qiao: J. Mater. Sci. Technol., 2019, vol. 35, pp. 917–25.10.1016/j.jmst.2018.11.023 ↗
54. 54 R.P. Kusy, J.Q. Whitley, and M.J. Prewitt: Angle Orthod, 1991, vol. 61, pp. 293–302.
55. 55 Y. Guilmard, J. Denape, and J.A. Petit: Tribol. Int., 1993, vol. 26, pp. 29–39.10.1016/0301-679X(93)90036-Z ↗
56. 56 Y.H. Wu, H.J. Yang, R.P. Guo, X.J. Wang, X.H. Shi, P.K. Liaw, and J.W. Qiao: Wear, 2020, vol. 460–461, pp. 1–13.
57. A. Saeed-Akbari, J. Imlau, U. Prahl, and W. Bleck: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 3076–90.10.1007/s11661-009-0050-8 ↗
58. 58 Y. Ikeda, I. Tanaka, J. Neugebauer, and F. Körmann: Phys. Rev. Mater., 2019, vol. 3, pp. 1–15.
59. 59 G.B. Olson and M. Cohen: Metall. Trans. A, 1976, vol. 7A, pp. 1897–904.
60. 60 B.C. De Cooman, Y. Estrin, and S.K. Kim: Acta Mater., 2018, vol. 142, pp. 283–362.10.1016/j.actamat.2017.06.046 ↗
61. 61 A.L. Bowman, G.P. Arnold, E.K. Storms, and N.G. Nereson: Acta Crystallogr. Sect. B Struct. Crystallogr. Cryst. Chem., 1972, vol. 28, pp. 3102–3.10.1107/S0567740872007526 ↗
62. 62 J. Glaser, R. Schmitt, and H.-J. Meyer: Zeitschrift für Naturforsch. B, 2003, vol. 58, pp. 929–33.
63. 63 B. Xiao, J.D. Xing, J. Feng, Y.F. Li, C.T. Zhou, W. Su, X.J. Xie, and Y.H. Chen: Phys. B Condens. Matter, 2008, vol. 403, pp. 2273–81.10.1016/j.physb.2007.12.012 ↗
64. 64 N. P. Suh: Wear, 1973, vol. 25, pp. 111–24.10.1016/0043-1648(73)90125-7 ↗
65. 65 M. Amiri and M.M. Khonsari: Entropy, 2010, vol. 12, pp. 1021–49.10.3390/e12051021 ↗
66. 66 Q. Chen and D.Y. Li: Wear, 2005, vol. 259, pp. 1382–91.10.1016/j.wear.2004.12.025 ↗
67. 67 Y. Chen, Y. Li, S. Kurosu, K. Yamanaka, N. Tang, Y. Koizumi, and A. Chiba: Wear, 2014, vol. 310, pp. 51–62.10.1016/j.wear.2013.12.010 ↗
68. I. Hutchings and P. Shipway: Tribology: Friction and Wear of Engineering Material, 2nd edn., Elsevier, Amsterdam, 2017.
69. K.-H. Zumahr: Microstructure and Wear of Materials, Elsevier, Amsterdam, 1987.
70. 70 Z. Huang, J. Xing, and A. Zhang: J Mater Sci Technol, 2006, vol. 22, pp. 775–8.10.1179/174328406X101346 ↗
71. R. Ghasemi and L. Elmquist: 10th Inter. Symp. Sci. Process. Cast. Iron. – SPCI10, 2014, pp. 1–7.
72. 72 Q.C. Li, R.X. Li, X.D. Yue, G.W. Chang, and Q.J. Zhai: Mater. Chem. Phys., 2008, vol. 112, pp. 402–6.10.1016/j.matchemphys.2008.05.073 ↗
73. 73 Y. Hao, J. Li, X. Li, W. Liu, G. Cao, C. Li, and Z. Liu: J. Mater. Process. Technol., 2020, vol. 275, pp. 1–9.