journal article·2019-04-15Open access

Measurement and Prediction of Phase Transformation Kinetics in a Nuclear Steel During Rapid Thermal Cycles

G. Obasi, E. J. Pickering, A. N. Vasileiou, Y. L. Sun, D. Rathod, M. Preuss, J. A. Francis, M. C. Smith

Abstract

Abstract Accurate prediction of the residual stress distributions in steel welds can only be achieved if consideration is given to solid-state phase transformation behavior. In this work, we assess the ability of a model for reaction kinetics to predict the phase transformations, and corresponding evolution of volumetric strain, in a nuclear pressure vessel steel when subjected to rapid weld-like thermal cycles. The cases under consideration involved the rapid heating of SA508 steel to a temperature of either 900 °C or 1200 °C for a period of 10 seconds, and subsequent cooling of the material to room temperature at rates between 0.1 and 100 °C s−1. Predictions for the microconstituent proportions and transformation temperatures for each thermal cycle are compared to those measured through a combination of dilatometry, optical and electron microscopy, and synchrotron X-ray diffraction. In general, there was good agreement between measured and predicted transformation start temperatures and microconstituent fractions for cooling rates relevant to welding ($$ \ge $$ 10 °C s−1). Even in the cases in which discrepancies were found for start temperatures, examination of the corresponding dilatation curves showed a good match between predicted and experimental transformation strain evolution. This is a very positive result in terms of residual stress prediction in welds. At slower cooling rates, significant discrepancies arose owing to the model’s incapacity to predict Widmanstätten ferrite or retained austenite, and its failure to account for the effects of carbon redistribution during transformations involving diffusion. Although not relevant to welding, improvements to the model to rectify these issues would be beneficial in terms of its wider predictive capabilities.
Source: crossref · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Welding Techniques and Residual Stresses · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (62)

Show source-provided references
1. D. P. G. Lidbury: Int. J. Press Vessel. Pip., 1984, vol. 17, 197–328.10.1016/0308-0161(84)90028-0 ↗
2. D.T. Read: Eng. Fract. Mech., 1989, vol 32, 147–153.10.1016/0013-7944(89)90212-9 ↗
3. X. Cheng, J.W. Fisher, H.J. Prask, T. Gnaupel-Herold, B.T. Yen, S. Roy: Int. J. Fatigue., 2003, vol. 25, 1259–1269.10.1016/j.ijfatigue.2003.08.020 ↗
4. W. Fricke: Mater. Werkstofftechn., 2005, vol. 36, 642–64.10.1002/mawe.200500933 ↗
5. M. Turski, A.H. Sherry, P.J. Bouchard, P.J. Withers: J. Neutron Res., 2004, vol. 12, 45–49.10.1080/10238160410001734441 ↗
6. P.J. Bouchard, P.J. Withers, S.A. McDonald, R.K. Heenan: Acta Mater. 2004, vol. 52, 23–34.10.1016/j.actamat.2003.08.022 ↗
7. D. J. Hornbach and P. S. Prevey: J. Press. Technol., 2002, vol. 124, 359–365.10.1115/1.1481035 ↗
8. S. Sjöström: Mater. Sci. Technol.: 1985, vol. 1, 823-82910.1179/mst.1985.1.10.823 ↗
9. J.A. Francis, H.K.D.H. Bhadeshia, P.J. Withers: Mater. Sci. Technol., 2007, vol. 23, 1009–1020.10.1179/174328407X213116 ↗
10. C.J. Hamelin, O. Muránsky, M.C. Smith, T.M. Holden, V. Luzin, P.J. Bendeich, L. Edwards: Acta Mater., 2014, vol. 75, 1–19.10.1016/j.actamat.2014.04.045 ↗
11. G.W. Greenwood, R.H. Johnson: Proc. Roy. Soc., 1965, 283, 403–422.
12. G. Wassermann: Arch. Eisenhuettenw., 1937, vol. 10, 321.
13. C.L. Magee, H.W. Paxton, Ph.D. Thesis, 1966, Carnegie Inst. Technol., Pittburgh, PA.
14. Y.E. Majaty, J.-B. Leblond, D. Kondo: J. Mech. Phys. Solids., 2018, vol. 121, 175–197.10.1016/j.jmps.2018.07.014 ↗
15. D. Weisz-Patrault: J. Mech. Phys. Solids., 2017, vol. 106, 152–175.10.1016/j.jmps.2017.05.019 ↗
16. J.B. Leblond, G. Mottet, J.C. Devaux: J. Mech. Phys. Solids., 1984, vol. 34, 411–432.10.1016/0022-5096(86)90010-4 ↗
17. J.-B. Leblond, G. Mottet, J. Devaux: J. Mech. Phys. Solids., 1986, vol. 34, 395–409.10.1016/0022-5096(86)90009-8 ↗
18. D.F. Watt, L. Coon, M. Bibby, J. Goldak, C. Henwood: Acta Metall., 1988, vol. 36, 3029–3035.10.1016/0001-6160(88)90185-X ↗
19. H. Dai, J.A. Francis, P.J. Withers: Mater. Sci. Technol., 2013, vol. 26, 940-949.10.1179/026708309X12459430509454 ↗
20. H. Dai, J.A. Francis, H.J. Stone, H.K.D.H. Bhadeshia, P.J. Withers: Metall. Mater. Trans. A., 2008, vol. 39, 3070-3078.10.1007/s11661-008-9616-0 ↗
21. ASTM: Standard Specification for Quenched and Tempered Vacuum- Treated Carbon and Alloy Steel Forgings for Pressure Vessels 1, Test. 01, 1999, 1–6.
22. Y. K. Suzuki, I. Kurihara, T. Sasaki, Y. Koyoma, Tanaka: Nucl. Eng. Des., 2001, vol. 206, 261–278.
23. E.J. Pickering, H.K.D.H. Bhadehia: Metall. Mater. Trans. A., 2014, vol. 45A, 2983–2997.10.1007/s11661-014-2253-x ↗
24. E.J. Pickering, C. Chesma, S. Al-Bermani, M. Holland, P. Davies, J. Talamantes-Silva: Metall. Mater. Trans. B., 2015, vol. 46, 1860–1874.10.1007/s11663-015-0386-y ↗
25. H. Yang, H.K.D.H Bhadeshia: Mater. Sci. Technol., 2007, vol. 23, 556-560.10.1179/174328407X176857 ↗
26. M. Onink, C.M. Brakman, F.D. Tichelaar, E.J. Mittemeijer, S. van der Zwaag, J.H. Root, N.B. Konyer: Scr. Metall. Mater., 1993, vol. 29, 1011-1016.10.1016/0956-716X(93)90169-S ↗
27. A. Hammersley: Fit2D software package, 1998, ESRF, http://www.esrf.eu/computing/scientific/FIT2D/.
28. Bruker AXS GmbH: TOPAS software package, version 4.2, 2009.
29. F. Bachmann, R. Hielscher, H. Schaeben: Solid State Phenom., 2010, vol. 160, 63–68.10.4028/www.scientific.net/SSP.160.63 ↗
30. L.R.R. Nitter: L’Image software package, http://Limagesoftware.Net., 1997.
31. M.V. Li, D.V. Niebuhr, L.L. Meekisho, D.G. Atteridge, Metall. Mater. Trans. B., 1998, vol. 29, 661-672.10.1007/s11663-998-0101-3 ↗
32. A.N. Vasileiou, M.C. Smith, J. Balakrishnan, J.A. Francis, C.J. Hamelin: Nucl. Eng. Des., 2017, vol. 323, 309–316.10.1016/j.nucengdes.2017.03.040 ↗
33. D. Venugopalan, J.S. Kirkaldy: Phase Transformations in Ferrous Alloys, eds. A.R. Marder and J.I. Goldstein, 1984, New York, AIME.
34. Thermo-Calc software package, version 2017a, TCFE8 database, 2017.
35. R. A. Grange: Metal Prog., 1961, vol. 79, 73-75.
36. K.W. Andrews: J. Iron Steel Inst., 1965, 721–27.
37. J. Barralis and G. Maeder: Metallurgie [Tome I, Metallurgie Phys], 1982, Collect. Sci. ENSAM.
38. [38] N.O. Meara, H. Abdolvand, J.A. Francis, S.D. Smith, P.J. Withers: Mater. Sci. Technol., 2016, vol. 32, 1517-1532.10.1080/02670836.2015.1132529 ↗
39. S. Erich: Zeitschrift Für Metallk., 1942, vol. 34.3, 70-72.
40. M. Avrami: J. Chem. Phys., 1941, vol. 9.2, 177-184.10.1063/1.1750872 ↗
41. M. Avrami: J. Chem. Phys., 1940, vol. 8.2, 212-224.10.1063/1.1750631 ↗
42. M. Avrami: J. Chem. Phys. 1939, vol. 7.12, 1103-1112.10.1063/1.1750380 ↗
43. C.Y. Kung, J.J. Rayment: Metall. Trans. A., 1982, vol. 13, 328-331.10.1007/BF02643327 ↗
44. D.P. Koistinen, R.E. Marburger: Acta Metall., 1959, vol. 7, 59–60.10.1016/0001-6160(59)90170-1 ↗
45. Daussault Systems, Inc. 2013. ‘‘SIMULIA. ABAQUS/Standard, Daussault Syst. Inc. (2013).
46. J. Bouchard, M.C. Smith, and S.K. Bate: ASME 2013 Press. Vessel. Pip. Conf., 2013, Paris, France.
47. S.K. Bate:, Protocol for finite element simulations of an autogenous welded beam specimen, Serco Gr. Plc, 2010.
48. H. Pous-romero, I. Lonardelli, D. Cogswell, H.K.D.H. Bhadeshia: Mater. Sci. Eng. A., 2013, vol. 567, 72–79.10.1016/j.msea.2013.01.005 ↗
49. H.K.D.H. Bhadeshia: Metall. Trans. A., 1979, vol. 10, 895–907.10.1007/BF02658309 ↗
50. E. Kozeschnik, H.K.D.H. Bhadeshia: Mater. Sci. Technol., 2008, vol. 24, 343–347.10.1179/174328408X275973 ↗
51. H.K.D.H. Bhadeshia, Bainite in steels: theory and practice, 3rd ed., 2015, Maney, Leeds, UK.
52. C. Morris, E.S. Machlin: Trans. Met. Soc. AIME., 1951, vol. 191, 746-754.
53. E. M. Breinan and G.S. Ansel: Metall. Trans., 1970, vol. 1, 1513-1520.10.1007/BF02641994 ↗
54. J.R. Strife, M.J. Carr, G.S. Ansell: Metall. Trans. A., 1977, vol. 8, 1471-1484.10.1007/BF02642861 ↗
55. S. Kajiwara: Metall. Mater. Trans. A., 1986, vol. 17, 1693-1702.10.1007/BF02817268 ↗
56. S.M.C. van Bohemen, J. Sietsma: Mater. Sci. Eng. A., 2010, vol. 527, 6672–6676.10.1016/j.msea.2010.06.091 ↗
57. P.J. Brofman, G.S. Ansell: Metall. Trans. A., 1983, vol. 14A, 1929-1931.10.1007/BF02645565 ↗
58. S. Lee, Y. Lee: Mater. Sci. Forum., 2005, vol. 479, 3169–3172.10.4028/www.scientific.net/MSF.475-479.3169 ↗
59. D. Turnbull, J.C. Fisher, J.H. Hollomon: Met. Trans., 1949, vol. 185, 691-700.
60. W.C. Leslie, R.L. Miller: ASM Trans., 1964, vol. 57, 972–979.
61. J.R.C. Guimaraes: Scripta Mater., 2007, vol. 57, 237–239.10.1016/j.scriptamat.2007.04.002 ↗
62. J. Hidalgo, M.J. Santofimia: Metall. Mater. Trans. A., 2016, vol. 47, 5288–5301.10.1007/s11661-016-3525-4 ↗