Effect of Alloying Element Partition in Pearlite on the Growth of Austenite in High-Carbon Low Alloy Steel
Source abstract
Abstract
The growth of austenite from pearlite in high-carbon low alloy steel occurs with and without alloy element redistribution depending on the amount of superheating above the eutectoid temperature. The transition temperature of austenite growth (denoted PNTT) is calculated as a function of pearlite transformation temperature and subsequent holding time, which affect the degree of partitioning in pearlite, using experimental partition coefficients k θ/α of Mn, Cr, Co, Si, and Ni reported in the literature. PNTT is the highest in Cr-containing alloys which have the largest k θ/α in pearlite. Post-transformation aging, usually accompanied by cementite spheroidization, leads to a marked increase of PNTT in Mn and Cr alloys. PNTT of Ni alloy does not depend on pearlite transformation temperature because practically the formation of partitioned pearlite is severely limited in this alloy for kinetic reasons. Above PNTT, austenite growth occurs fast initially, but slows down in the order of ten seconds when the ferrite disappears, and the remaining small carbide particles dissolve very slowly under the control of alloy element diffusion.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. R.F. Mehl and W.C. Hagel: Prog.Met.Phys., 1956, vol. 6, pp. 74-13410.1016/0502-8205(56)90005-3 ↗
2. G. Molinder: Acta Metall., 1956, vol. 4, pp. 565-57110.1016/0001-6160(56)90157-2 ↗
3. R.R. Judd and H.W Paxton: Trans. TMS-AIME, 242(1968), 206-215.
4. G.R. Speich and A. Szirmae: Trans. TMS-AIME, 245(1969), 1063-1074
5. M. Hillert, K. Nilsson, L.E. Törndahl: JISI, 1971, vol. 209, pp. 49-66.
6. D.E. Coates: Metal. Trans., 1972, vol. 3, pp. 1203-1212.10.1007/BF02642453 ↗
7. D.E. Coates: Metal. Trans., 1972, vol. 4, pp. 1077-1086.10.1007/BF02645611 ↗
8. J.B. Gilmour, G.R. Purdr, and J.S. Kirkaldy, Metall.Trans., vol. 3, 1972, 1455-146410.1007/BF02643033 ↗
9. Y. Xia, M. Enomoto, Z.G. Yang, Z.D. Li and C. Zhang: Phil.Mag., 2013, vol. 93, pp. 1095-1109.10.1080/14786435.2012.744484 ↗
10. N. Ridley: In Phase Transformations in Ferrous Alloys, eds. A.R. Marder and J.I. Goldstein, TMS, Warrendale, PA, 1984, pp. 201–36.
11. M.L. Picklesimer, D.L. McElroy, T.M. Kegley, Jr., E.E. Stansbury and J.H. Frye, Jr., TMS-AIME, 1960, vol. 218, pp. 473-480
12. N.A. Razik, G.W. Lorimer, N. Ridley: Acta Metall., 1974, vol. 22, pp. 1249-1258.10.1016/0001-6160(74)90138-2 ↗
13. N.A. Razik, G.W. Lorimer, N. Ridley: Metall. Trans. A, 1976, vol. 7, pp. 209-214.10.1007/BF02644458 ↗
14. J. Chance and N. Ridley: Metall. Trans. A, 1981, vol. 12A, pp. 1205-121310.1007/BF02642334 ↗
15. N. Ridley, D. Burgess: Metal Science, 1984, vol. 18, pp. 7-12.10.1179/030634584790420320 ↗
16. S.A. Al-Salman, G.W. Lorimer and N. Ridley: Acta Metall., 1979, vol. 27, pp. 1391-1400.10.1016/0001-6160(79)90208-6 ↗
17. S.A. Al-Salman and N. Ridley: Scripta Metall., 1984, vol. 18, pp. 789-791.10.1016/0036-9748(84)90395-8 ↗
18. S.A. Al-Salman, G.W. Lorimer and N. Ridley: Metall. Trans. A, 1979, vol. 10, pp. 1703-1709.10.1007/BF02811704 ↗
19. N. Ridley, M.A. Malik and G.W. Lorimer: Mater. Char., 1990, vol. 25, pp. 125-14110.1016/1044-5803(90)90025-F ↗
20. A.E. Nehrenberg, Trans. AIME, vol. 188, 1950, 162-174
21. L. Karmazin: Mater.Sci.Eng., vol. A142, 1991, 71-7710.1016/0921-5093(91)90755-C ↗
22. M.M. Aranda, R. Rementeria, J. Poplawsky, E. Urones-Garrote and, C. Capdevila: Scripta Mater., vol. 104, 2015, 67-7010.1016/j.scriptamat.2015.04.005 ↗
23. Thermo-calc is Trademark of Thermo-Calc Software: http://www.thermocalc.com/
24. J.S. Kirkaldy, B.A. Thomson, and E.A. Baganis: In Hardenability Concepts with Applications to Steel, eds. D.V. Doane and J.S. Kirkaldy, TMS, 1978, pp. 82–125
25. S.K. Tewari and P.C. Sharma: Metall. Trans. A, vol. 16 , 1985, 597–60310.1007/BF02814233 ↗
26. M. Hillert: In Solid → Solid Phase Transformations, eds. H.I. Aaronson, D.E. Laughlin, R.F. Sekerka and C.M. Wayman, TMS, 1981, pp. 789–805.
27. C.R. Hutchinson, R.E. Hackenberg and G.J. Shiflet: Acta mater., 2004, vol. 52, pp. 3565-3585.10.1016/j.actamat.2004.04.010 ↗
28. M. Gouné, P. Maugis, and J. Drillet: J. Mater. Sci. Technol., 2012, vol. 28, pp. 728-736.10.1016/S1005-0302(12)60122-4 ↗
29. J.D. Faires and R.L. Burden: Numerical Method, PWS-KENT Publishing Company, Boston, 1993, pp.32-33
30. G. Miyamoto, H. Usuki, Z.D. Li and T. Furuhara: Acta Mater., 2010, vol. 58, pp. 4492-450210.1016/j.actamat.2010.04.045 ↗
31. L. Kong, Y.H. Liu, J. Liu, Y Song, S.S. Li, R.H. Zhang, T.J. Li, Y. Liang: J. Alloys Comp., vol. 648, 2015, 494-49910.1016/j.jallcom.2015.06.259 ↗
32. T. Nishizawa, Bulletin of Japan Institute of Metals, vol. 12, 1973, 401-417.10.2320/materia1962.12.401 ↗
33. J. Ågren and G.P. Vassilev: Mater.Sci.Eng., 1984, vol. 64, pp. 95-10310.1016/0025-5416(84)90076-4 ↗
34. Z.K. Liu, L. Höglund, B. Jönsson and J. Ågren: Metall.Trans.A, 1991, vol. 22A, pp.1745-1752.10.1007/BF02646498 ↗
35. G.H. Zhang, J.Y. Chae, K.H.Kim, D.W. Suh: Mater.Sci.Eng., vol. 81, 2013, 56-67
36. J.D. Verhoeven and E.D. Gibson: Metall.Mater.Trans.A, 1998, vol. 29A, pp.1181-118910.1007/s11661-998-0245-4 ↗
37. D.V. Shtansky, K. Nakai, and Y. Ohmori: Acta Mater., 1999, vol. 47, pp. 2619-32.10.1016/S1359-6454(99)00142-1 ↗
38. Z.D. Li, G. Miyamoto, Z.G. Yang, T. Furuhara: Metall.Mater.Trans.A, 2011, vol. 42A, 1586-159610.1007/s11661-010-0560-4 ↗