The effect of solution annealing on the microstructural behavior of alloy 22 welds
Source abstract
Abstract
Multipass gas tungsten arc welds of alloy 22 were subjected to solution annealing durations of 20 minutes, 24 hours, 72 hours, and 1 week at temperatures of 1075 °C, 1121 °C, 1200 °C, and 1300 °C. The specimens were studied in cross section by secondary electron microscopy to determine the effect of solution annealing on tetrahedrally close-packed (TCP) precipitate stability. Electron backscatter diffraction mapping was also performed on all of the specimens to determine the recrystallization behavior of the welds. It was found that complete TCP precipitate dissolution occurs after solution annealing at 1075 °C and 1121 °C for 24 hours, and at 1200 °C and 1300 °C for durations of 20 minutes. Regions of most rapid recrystallization were correlated to the regions of lowest solute content, highest plastic strain, and highest residual stresses. Texture analysis indicated that while the columnar dendrites originally present in the weld grew with a 〈001〉 orientation in the transverse direction (approximately opposite the heat flow direction), the recrystallized grains adopt a 〈101〉 orientation in the transverse direction when recrystallization and TCP phase dissolution occur simultaneously.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Advanced materials and composites · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. ASTM Standard B 575-04, ASTM International, West Conshohocken, PA, 2004.
2. D. Dunn, G. Cragnolino, and N. Sridhar: Scientific Basis for Nuclear Waste Management XXIII, Materials Research Society, Warrendale, PA, 2000, vol. 608, pp. 89–94.
3. R. Rebak, N. Koon, J. Dillman, and P. Crook: Corrosion/2000, NACE International, Houston, TX, 2000, paper no. 181.
4. P. Manning and J. Schöbel: Werkstoffe Korr., 1986, vol. 37, pp. 137–45.10.1002/maco.19860370305 ↗
5. I. Asphahani: Arabian J. Sci. Eng., 1989, vol. 14 (2), p. 317.
6. R. Rebak: Passivity and Localized Corrosion, The Electrochemical Society, Pennington, NJ, 1998, vol. 97 (26), p. 1001.
7. R. Rebak and N. Koon: Corrosion/98, NACE International, Houston, TX, 1998, paper no. 153.
8. K. Gruss, G. Cragnolino, D. Dunn, and N. Sridhar: Corrosion/98, NACE International, Houston, TX, 1998, paper no. 149.
9. R. Rebak and P. Crook: Critical Factors in Localized Corrosion III, The Electrochemical Society, Pennington, NJ, 1999, vol. 98 (17), p. 289.
10. T.S.E. Summers, M.A. Wall, M. Kumar, S.J. Matthews, and R.B. Rebak: Scientific Basis for Nuclear Waste Management XXII, Materials Research Society, Warrendale, PA, 1999, vol. 556, pp. 919–26.
11. R. Rebak and P. Crook: Transportation, Storage, and Disposal of Radioactive Materials, ASME International, New York, NY, 2002, vol. PVP-449, p. 111.10.1115/PVP2002-1621 ↗
12. M.J. Cieslak, T.J. Headley, and A.D. Romig: Metall. Trans. A, 1986, vol. 17A, pp. 2035–47.10.1007/BF02645001 ↗
13. J.S. Ogborn, D.L. Olson, and M.J. Cieslak: Mater. Sci. Eng. A, 1995, vol. 203, pp. 134–36.10.1016/0921-5093(95)09832-1 ↗
14. T.S.E. Summers, R.B. Rebak, and R.R. Steely: 2000 TMS Fall Meeting, St. Louis, MO, paper no. LLNL, UCRL-JC-137727.
15. T.S.E. Summers, R.B. Rebak, T.A. Palmer, and P. Crook: Scientific Basis for Nuclear Waste Management XXV, Materials Research Society, Warrendale, PA, 2002, vol. 713, pp. 45–52.
16. Hastelloy C-22 Alloy, Haynes International, Kokomo, IN, 1997, p. 16.
17. Y.-M. Pan, D.S. Dunn, and G.A. Cragnolino: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 1143–51.10.1007/s11661-005-0207-z ↗
18. B.S. El-Dasher and S.G. Torres: Pressure Vessel and Piping Conf., ASME International, New York, NY, 2005, paper no. PVP-2005-71665.
19. SFA-5.14, ERNiCrMo-10, ASME International, New York, NY, 2004, Sect. II, p. 325.10.1108/13552550410554311 ↗
20. J.E. Hilliard: Quantitative Microscopy, McGraw-Hill, New York, NY, 1968.
21. S.I. Wright and B.L. Adams: Metall. Trans. A, 1992, vol. 23A, pp. 759–68.10.1007/BF02675553 ↗
22. B.L. Adams, S.I. Wright, and K. Kunze: Metall. Trans. A, 1993, vol. 24A, pp. 819–31.10.1007/BF02656503 ↗
23. C.A. Shuh, K. Anderson, and C. Orme: Surf. Sci., 2003, vol. 544, pp. 183–92.10.1016/j.susc.2003.07.009 ↗
24. D.A. Porter and K.E. Easterling: Phase Transformations in Metals and Alloys, 2nd ed., Chapman & Hall, London, 1996, p. 68.
25. L. Zhuang, J. Bottema, P. Kaasenbrood, W.S. Miller, and P. De Smet: Mater. Sci. Forum, vols. 217–222, p. 487.10.4028/www.scientific.net/MSF.217-222.487 ↗
26. S. Kou: in Welding Metallurgy, 2nd ed., John Wiley & Sons, Hoboken, NJ, 2003, p. 124.
27. A.T. Dewald, J.E. Rankin, M.R. Hill, M.J. Lee, and H. Chen: J. Eng. Mater. Technol., 2004, vol. 126, pp. 465–73.10.1115/1.1789957 ↗
28. M.B. Prime: ASME J. Eng. Mater. Technol., 2001, vol. 123, pp. 162–68.10.1115/1.1345526 ↗
29. D. Turnbull and J.C. Fisher: J. Chem. Phys., 1949, vol. 17, pp. 71–73.10.1063/1.1747055 ↗
30. P. Cotterill and P.R. Mould: Recrystallization and Grain Growth in Metals, John Wiley & Sons, New York, NY, 1976, p. 62.
31. K. Lücke and K. Detert: Acta Metall., 1957, vol. 5, pp. 628–37.10.1016/0001-6160(57)90109-8 ↗
32. P. Gordon and R.A. Vandermeer: Trans. TMS-AIME, 1962, vol. 224, p. 917.
33. J.W. Cahn: Acta Metall., 1962, vol. 10, pp. 789–98.10.1016/0001-6160(62)90092-5 ↗