journal article·2019-12

Effect of Strain-Induced Precipitation on the Austenite Non-recrystallization (Tnr) Behavior of a High Niobium Microalloyed Steel

V. Rajinikanth, Tipu Kumar, B. Mahato, Sandip Ghosh Chowdhury, Sandeep Sangal

Publisher page

Abstract

The non-recrystallization temperature (Tnr) of high niobium microalloyed steel was determined from both multihit and double-hit compression tests obtained under plane strain condition. The Tnr was determined to be in the range of 985 °C to 1010 °C for multihit conditions. The double-hit tests carried out at an interpass time of 5 seconds gave very low Tnr in the range of 860 °C to 900 °C. In order to understand this, double-hit experiments were carried out for different interpass times (2, 15, 100 seconds) at three different temperatures (950 °C, 1050 °C, and 1150 °C). The negative softening behavior was observed at 950 °C for higher interpass times of 15 and 100 seconds. This implies that the Tnr of this steel is well above 950 °C. This was due to the high amount of strain-induced precipitation of niobium carbonitrides at higher interpass times as revealed from TEM investigation. The precipitate size evolution considering the Dutta and Sellars nucleation condition in TC-PRISMA agrees well with the experimentally observed precipitate sizes. However, the evolution of Zener pinning forces considering TC-PRISMA nucleation condition is similar to both reported and experimentally determined values. The evolution of tensile properties also correlates well with the observed austenite recrystallization softening behavior. Therefore, a minimum interpass time of 15 seconds is required during double-hit compression tests to effectively precipitate Nb(C, N) and delay the static recrystallization softening behavior of this steel. This lead to the determination of comparable Tnr values between double-hit and multihit methods.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. L. Backe: PhD Thesis, Material Science and Engineering, School of Industrial Engineering and Management, Royal Institute of Technology, Sweden, 2009.
2. R.D.K. Misra, G.C. Weatherly, J.E. Hartmann and A.J. Boucek: Mater. Sci. Technol., 2001, vol.17, pp.1119-29.10.1179/026708301101511040 ↗
3. H.G. Hillenbrand, M. Gras, and C. Kalwa: Niobium 2001, Orlanda, USA, December 2–5, 2001.
4. D.B. Rosado W.D. Waele, D. Vanderschueren, and S. Hertelé: Latest developments in mechanical properties and metallurgical features of high strength line pipe steels (Academic Bibliography, Universiteit Gent, Sustainable construction and design, 2013). https://biblio.ugent.be/publication/3219348/file/3219414. Accessed 24 Feb 2019.
5. S. Vervynckt, K. Verbeken, P. Thibaux, M. Liebeherr and Y. Houbaert: Mater. Sci. Forum, 2010, vol. 638-642, pp. 3567-72.10.4028/www.scientific.net/MSF.638-642.3567 ↗
6. S. Vervynckt, K. Verbeken, P. Thibaux, and Y. Houbaert: Mater. Sci. Eng. A, 2011, vol. 528, pp. 5519-28.10.1016/j.msea.2011.03.087 ↗
7. S. Vervynckt, K. Verbeken, P. Thibaux, M. Liebeherr and Y. Houbaert: ISIJ Int., 2009, vol. 49, pp. 911-20.10.2355/isijinternational.49.911 ↗
8. M. Gomez, S.F. Medina and P. Valles: ISIJ Int., 2005, vol. 45, pp. 1711-20.10.2355/isijinternational.45.1711 ↗
9. R. Abad, A.I. Fernandez, B. Lopez and J.M. Rodriguez-Ibabe: ISIJ Int., 2001, vol. 41, pp. 1295-300.10.2355/isijinternational.41.1373 ↗
10. M.I. Vega, S.F. Medina, M. Chapa, A. Quispe: ISIJ Int., 1999, vol. 39, pp. 1304-10.10.2355/isijinternational.39.1304 ↗
11. L.P. Karjalainen, T.M. Maccagno and J. J. Jonas: ISIJ Int., 1995, vol. 35, pp. 1523-31.10.2355/isijinternational.35.1523 ↗
12. N. Radovic, D. Drobnjak and K. Raic: MJoM, 2009, vol. 15, pp. 99-104.
13. S. Vervynckt, K. Verbeken, B. Lopez, and J.J. Jonas: Int. Mater. Rev., 2012, vol. 57, pp. 187-207.10.1179/1743280411Y.0000000013 ↗
14. C.N. Homsher: Masters thesis, Colorado School of Mines, 2013.
15. C.N. Homsher, and C.J. Van Tyne: Mater. Perform. Charact., 2015, vol. 4, pp. 293-306.10.1520/MPC20150002 ↗
16. S. Vervynckt, K. Verbeken, P. Thibaux, and Y. Houbaert: Steel Res. Int., 2010, vol. 82, pp. 369-78.10.1002/srin.201000167 ↗
17. T.M. Maccagno, J.J. Jonas, S. Yue, B.J. McCrady, R. Slobodian and D. Deeks: ISIJ Int., 1994, vol. 34, pp. 917-22.10.2355/isijinternational.34.917 ↗
18. J.J. Jonas: ISIJ Int., 2000, vol. 40, pp. 731-38.10.2355/isijinternational.40.731 ↗
19. L.N. Pussegoda and J.J. Jonas: ISIJ Int., 1991, vol. 31, pp. 278-88.10.2355/isijinternational.31.278 ↗
20. Z. Baochun, L. Guiyan, Y. Pingyuan and H. Lei: J. Mater. Res., 2016, vol. 31, pp. 2097-104.10.1557/jmr.2016.217 ↗
21. A.M. Elwazri, E. Essadiqi and S. Yue: ISIJ Int., 2004, vol. 44, pp. 162-70.10.2355/isijinternational.44.162 ↗
22. M. Gomez, S. F. Medina, A. Quispe and P. Valles: ISIJ Int., 2002, vol. 42, pp. 423-31.10.2355/isijinternational.42.423 ↗
23. C.Y. Zhao, G.L. Wu and X.B. Liu: J. South. Afr. Inst. Min. Metall., 2017, vol. 117, pp. 451-56.10.17159/2411-9717/2017/v117n5a7 ↗
24. S. Bao, G. Zhao, C. Yu, Q. Chang, C. Ye and X. Mao: Appl. Math. Model., 2011, vol. 35, pp. 3268-75.10.1016/j.apm.2011.01.024 ↗
25. L. Liang-yun, Q. Chun-lin, Z. De-wen, G. Xiu-hua, and D. Lin-xiu: J. Iron Steel Res. Int., 2011, vol. 18, pp. 55-60.10.1016/S1006-706X(11)60011-3 ↗
26. M. Gomez, L. Rancel and S.F. Medina: Met. Mater. Int., 2009, vol. 15, pp. 689-99.10.1007/s12540-009-0689-0 ↗
27. S.F. Medina and J.E. Mancilla: ISIJ Int., 1996, vol. 36, pp. 1077-83.10.2355/isijinternational.36.1077 ↗
28. S.F. Medina and A. Quispe: ISIJ Int., 1996, vol. 45, pp. 1295-300.10.2355/isijinternational.36.1295 ↗
29. S. Zhou, K. Zhang, N. Chen, J. Gu and Y. Rong: ISIJ Int., 2011, vol. 51, pp. 1688-95.10.2355/isijinternational.51.1688 ↗
30. Z. Jia, R.D.K. Misra, R.O. Malley, and S.J. Jansto: Mater. Sci. Eng. A, 2011, vol. 528, pp. 7077-83.10.1016/j.msea.2011.05.073 ↗
31. E.V. Pereloma, A.G. Kostryzhev, A. Alshahrani, C. Zhu, J.M. Cairney, C.R. Killmore and S.P. Ringer: Scr. Mater., 2014, vol. 75, pp. 74-77.10.1016/j.scriptamat.2013.11.026 ↗
32. W.M. Rainforth, M.P. Black, R.L. Higginson, E.J. Palmiere, C.M. Sellars, I. Prabst, P. Warbichler and F. Hofer: Acta Mater., 2002, vol. 50, pp. 735-47.10.1016/S1359-6454(01)00389-5 ↗
33. P. Motycka and M. Kover: 2nd International Conference on Recent Trends in Structural Materials, Plzen, Czech Republic, November 21–22, 2012.
34. V. Nagarajan, E.J. Palmiere and C. M. Sellars: Mater. Sci. Technol., 2009, vol. 25, pp. 1168-74.10.1179/174328409X455242 ↗
35. J.S. Langer and A. J. Schwartz: Phys. Rev. A 1980, vol. 21, pp. 948-58.10.1103/PhysRevA.21.948 ↗
36. R. W. Cahn, P. Haasen and E.J. Kramer: Material Science Technology, Wiley-VCHVerlag GmbH&Co. KGaA, Weinheim, Germany, 1991, pp. 213-304.
37. B. Dutta, E. Valdes and C.M. Sellars: Acta Metall. Mater., 1992, vol. 40, pp. 653-62.10.1016/0956-7151(92)90006-Z ↗
38. B. Dutta, E. J. Palmiere and C.M. Sellars: Acta Mater., 2001, vol. 49, pp. 785-94.10.1016/S1359-6454(00)00389-X ↗
39. M. Fukuhara and A. Sanpei: ISIJ Int., 1993, vol. 33, pp. 508-12.10.2355/isijinternational.33.508 ↗
40. J.W. Cahn: Acta Metall.,1956, vol. 4, pp. 572-75.10.1016/0001-6160(56)90158-4 ↗