Dynamic Strain Aging and Serration Behavior of Three High-Manganese Austenitic Steels
Source abstract
Abstract
The strain-rate dependence of the flow stress of three high-manganese austenitic steels with different compositions was studied in terms of dynamic strain aging and serration behavior at room temperature under quasi-static strain-rate ranges from 10−4 to 10−1 s−1. Tensile stress–strain curves showed that serrated flow occasionally appeared and the strain-rate dependence of flow stress was measured to be negative at all strains for Fe-22Mn-0.3C and Fe-30Mn-0.2C steels and at higher strain for Fe-30Mn-0.2C-1.5Al steel. Based on the tendency for a critical strain corresponding to the onset strain of serrated flow and electron back-scattered diffraction analysis, it was found that serrated flow was not induced by deformation twinning and $$ \gamma \to \varepsilon $$ martensitic transformation, but by dynamic strain aging associated with the interaction between partial dislocation and solute carbon. Also, the addition of Al content increased the critical strain, meaning that it effectively prohibits dynamic strain aging. In addition, dynamic strain aging promoted deformation twinning and/or $$ \gamma \to \varepsilon $$ martensitic transformation and resulted in negative strain-rate dependence of flow stress in the high-manganese austenitic steels.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. R.A. Hadfield: Science, 1888, vol. 12, pp. 284-6.
2. I.C. Yi, Y. Ha, K.H. Kwon, H. Lee and N.J. Kim: Mater. Sci. Eng. A, 2015, vol. 21, pp. 461-9.
3. J.E. Jin, M. Jung, C.Y. Lee, J. Jeong and Y.K. Lee: Met. Mater. Int., 2012, vol. 18, pp. 419-23.10.1007/s12540-012-3006-2 ↗
4. O. Grassel, L. Kruger, G. Frommeyer and L.W. Meyer: Int. J. Plast., 2000, vol. 16, pp. 1391-409.10.1016/S0749-6419(00)00015-2 ↗
5. G. Frommeyer, U. Brux and P. Neumann: ISIJ Int., 2003, vol. 43, pp. 438-46.10.2355/isijinternational.43.438 ↗
6. O. Bouaziz, S. Allain, C.P. Scott, P. Cugy and D. Barbier: Curr. Opin. Solid State Mater. Sci., 2011, vol. 15, pp. 141-68.10.1016/j.cossms.2011.04.002 ↗
7. I. Gutierrez-Urrutia and D. Raabe: Acta Mater., 2011, vol. 59, pp. 6449-62.10.1016/j.actamat.2011.07.009 ↗
8. J.K. Hwang, I.H. Son, J.Y. Yoo, A. Zargaran and N.J. Kim: Met. Mater. Int., 2015, vol. 21, pp. 815-22.10.1007/s12540-015-5273-1 ↗
9. J. E. Jung, J. Park, J.S. Kim, J.B. Jeon, S.K. Kim and Y.W. Chang: Met. Mater. Int., 2014, vol. 20, pp. 27-34.10.1007/s12540-014-1008-y ↗
10. G.B. Olson and M. Cohen: Metall. Trans. A, 1976, vol. 7, pp. 1897-904.
11. Y.K. Lee and C.S. Choi: Metall. Mater. Trans. A, 2000, vol. 31, pp. 355-60.10.1007/s11661-000-0271-3 ↗
12. K.G. Chin, C.Y. Kang, S.Y. Shin, S. Hong, S. Lee, H.S. Kim, K. Kim and N.J. Kim: 2011, Mater. Sci, Eng. A, vol. 528, pp. 2922-8.10.1016/j.msea.2010.12.085 ↗
13. D.C. Saha, S. Han, K.G. Chin, I. Choi and Y.D. Park: Steel Res. Int., 2012, vol. 83, pp. 352-7.10.1002/srin.201100324 ↗
14. M. Koyama, E. Akiyama, Y.K. Lee, D. Raabe and K. Tsuzaki: Int. J. Hydrogen Energy, 2017, vol. 42, pp. 12706-23.10.1016/j.ijhydene.2017.02.214 ↗
15. Y.N. Dastur and W.C. Leslie: Metall. Trans. A, 1981, vol. 12, pp. 749-59.10.1007/BF02648339 ↗
16. S.J. Lee, J. Kim, S.N. Kane and B.C. De Cooman: Acta Mater., 2011, vol. 59, pp. 6809-19.10.1016/j.actamat.2011.07.040 ↗
17. P.D. Zavattieri, V. Savic, L.G. Hector Jr., J.R. Fekete, W. Tong and Y. Xuan: Int. J. Plast., 2009, vol. 25, pp. 2298-2330.10.1016/j.ijplas.2009.02.008 ↗
18. R.A. Mulford and U.F. Kocks: Acta Metall., 1979, vol. 27, pp. 1125-34.10.1016/0001-6160(79)90130-5 ↗
19. L.P. Kubin and Y. Estrin: J. Phys. III, 1991, vol. 1, pp. 929-43.
20. B.C. De Cooman, K.G. Chin, and J. Kim: in New trends and developments in automotive system engineering: High Mn TWIP Steels for Automotive Applications, edited by M. Chiaberge, InTech, 2011.10.5772/14086 ↗
21. H.K. Yang, Z.J. Zhang, F.Y. Dong, Q.Q. Duan and Z.F. Zhang: Mater. Sci. Eng. A, 2014, vol. 607, pp. 551-8.10.1016/j.msea.2014.04.043 ↗
22. R. Alturk, L. G. Hector Jr., C.M. Enloe, F. Abu-Farha and T.W. Brown: JOM, 2018, vol. 70, pp. 894-905.10.1007/s11837-018-2830-3 ↗
23. I. Jung, S.J. Lee and B.C. De Cooman: Scr. Mater., 2012, vol. 66, pp.729-32.10.1016/j.scriptamat.2012.01.042 ↗
24. J. von Appen and R. Dronskowski: Steel Res. Int., 2011, vol. 82, pp. 101-7.10.1002/srin.201000260 ↗
25. W. Owen and M. Grujicic: Acta Mater., 1998, vol. 47, pp. 111-26.10.1016/S1359-6454(98)00347-4 ↗
26. T.S. Shun, C.M. Wan and J.G. Byrne: Scr. Metall., 1991, vol. 25, pp. 1769-74.10.1016/0956-716X(91)90302-H ↗
27. M. Koyama, T. Sawaguchi, T. Lee, C.S. Lee and K. Tsuzaki: Mater. Sci. Eng. A, 2011, vol. 528, pp. 7310-6.10.1016/j.msea.2011.06.011 ↗
28. Y. Nakada and A.S. Keh: Acta Metall., 1970, vol. 18, pp. 437-43.10.1016/0001-6160(70)90129-X ↗
29. Y. Tomota, M. Strum and J.W. Morris: Metall. Trans. A, 1986, vol. 17, pp. 537-47.10.1007/BF02643961 ↗
30. S.Y. Lee, S.I. Lee and B. Hwang: Mater. Sci. Eng. A, 2018, vol. 711, pp. 22-8.10.1016/j.msea.2017.10.074 ↗
31. H.K. Yang, Z.J. Zhang, Y.Z. Tian and Z.F. Zhang: Mater. Sci. Eng. A, 2017, vol. 690, pp. 146-57.10.1016/j.msea.2017.02.014 ↗
32. K.Renard and P.J. Jacques: Mater. Sci. Eng. A, 2012, vol. 542, pp. 8-14.10.1016/j.msea.2012.01.123 ↗