Determination of the Heat Transfer Coefficient at the Metal-Mold Interface During Centrifugal Casting
Source abstract
Abstract
The heat transfer coefficient at the metal-mold interface (h MM) has been determined for the first time during the centrifugal casting of a Fe-C alloy tube using the inverse solution method. To apply this method, a centrifugal casting experiment was carried out to measure cooling curves within the tube wall under a mold rotation speed of 900 rpm, imposing a centrifugal force 106 times as large as the gravity force (106 G). As part of the solution method, a comprehensive heat transfer model of the centrifugal casting was also developed and coupled to an optimization algorithm. Finally, the evolution of h MM with time that gives the minimum squared error between measured and calculated cooling curves was obtained. The determined h MM is approximately 870 W m−2 K−1 immediately after melt pouring, decreasing to about 50 W m−2 K−1 when the average temperature of the tube is ~973 K (700 °C), after the end of solidification. Despite the existence of a centrifugal force that could enhance the metal-mold contact, these values are lower than those generally reported for static molds with or without an insulating coating at the mold inner surface. The implemented model shows that the heat loss by radiation is dominant over that by convection at the tube inner surface, causing the formation of a solidification front that meets another front coming from the outer surface of the tube.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Metallurgical Processes and Thermodynamics · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. A. Royer and S. Vasseur: in ASM Handbook—Casting, D.M. Stefanescu, ed., ASM International, Metals Park, OH, 1998, pp. 296–307.
2. P. R. Beeley: Foundry Technology, Butterworth Heinemann, Oxford, 2001, pp. 622-645.10.1016/B978-075064567-6/50013-3 ↗
3. Y. Ebisu: Trans. AFS, 1977, vol. 85, pp. 643-59.
4. B. J. Yang, W. T. Liu and J. Y. Su: Trans. AFS, 1994, vol. 102, pp. 763-67.
5. G. Martinez, M. Garnier and F. Durand: Solidification Processing 1987, Proceedings of the Third International Conference, The Institute of Metals, London, 1988, pp. 357–60.
6. J. W. Gao and C. Y. Wang: Mat. Sci. Eng. A, 2000, vol. 292, pp. 207-15.10.1016/S0921-5093(00)01014-5 ↗
7. C. G. Kang, P. K. Rohatgi, C. S. Narendranath and G. S. Cole: ISIJ Int., 1994, vol. 34, pp. 247-54.10.2355/isijinternational.34.247 ↗
8. C. G. Kang and P. K. Rohatgi: Metall. Mater. Trans. B, 1996, vol. 27, pp. 277-85.10.1007/BF02915054 ↗
9. S. R. Chang, J. M. Kim and C. P. Hong: ISIJ Int., 2001, vol. 41, pp. 738-47.10.2355/isijinternational.41.738 ↗
10. P. S. S. Raju and S. P. Mehrotra: Mater. Trans. JIM, 2000, vol. 41, pp. 1626-35.10.2320/matertrans1989.41.1626 ↗
11. L. Drenchev, J. Sobczak, S. Malinov and W. Sha: Model. Simul. Mater. Sci. Eng., 2003, vol. 11, pp. 635-49.10.1088/0965-0393/11/4/314 ↗
12. L. Nastac, J.J. Valencia, J. Xu and H. Dong: Materials Processing in the Computer Age, V.R. Voller and H. Henein eds., The Minerals, Metals, and Materials Society, Materials Park, OH, 2000, pp. 1–18.
13. E. Panda, S. P. Mehrotra and D. Mazumdar: Metall. Mater. Trans. A, 2006, vol. 37, pp. 1675-87.10.1007/s11661-006-0109-8 ↗
14. Z. Xu, N. Song, R. V. Tol, Y. Luan and D. Li: IOP Conference Series: Materials Science and Engineering, 2012, vol. 33, pp. 012030.10.1088/1757-899X/33/1/012030 ↗
15. N. J. Humphreys, D. McBride, D. M. Shevchenko, T. N. Croft, P. Withey, N. R. Green and M. Cross: Applied Mathematical Modelling, 2013, vol. 37, pp. 7633-43.10.1016/j.apm.2013.03.030 ↗
16. R. Heringer, M. Boccalini, Jr, M.A. Martorano, and C. Serantoni: ASME Summer Heat Transfer Conference - HT2008, ASME, New York, 2008, vol. 2008, pp. 693–94.10.1115/HT2008-56103 ↗
17. M. A. Martorano and J. D. T. Capocchi: Int. J. Heat Mass Transf., 2000, vol. 43, pp. 2541-52.10.1016/S0017-9310(99)00298-7 ↗
18. M. Rappaz: Int. Mater. Rev., 1989, vol. 34, pp. 93-123.10.1179/imr.1989.34.1.93 ↗
19. H. Baker: in ASM Handbook—Alloy Phase Diagrams, H. Baker, ed., American Society for Metals, Metals Park, OH, 1992, pp. 2.110–2.10.
20. S. Seghir-Ouali, D. Saury, S. Harmand, O. Phillipart and D. Laloy: Int. J. Therm. Sci., 2006, vol. 45, pp. 1166-78.10.1016/j.ijthermalsci.2006.01.017 ↗
21. C. A. Santos, J. M. V. Quaresma and A. Garcia: J. Alloy Compd., 2001, vol. 319, pp. 174-86.10.1016/S0925-8388(01)00904-5 ↗
22. W. Kurz and D. J. Fisher: Fundamentals of Solidification, Trans Tech Publications, Aedermannsdorf, 1989, pp. 130-135.
23. F. P. Incropera and D. P. DeWitt: Fundamentals of heat and mass transfer, Wiley, New York, 1996, pp. 811-847.
24. M. F. Modest: Radiative Heat Transfer, Academic, San Diego, CA, 2003, pp. 762-773.10.1016/B978-012503163-9/50027-8 ↗
25. C. J. Smithells, E. A. Brandes and G. B. Brook: Smithells metals reference book, Butterworth-Heinemann, Oxford, 1992, pp. 14.1 - 14.5.
26. D. D. Goettsch and J. A. Dantzig: Metall. Mater. Trans. A, 1994, vol. 25, pp. 1063-79.10.1007/BF02652281 ↗
27. U. Ekpoom and R. W. Heine: Trans. AFS, 1981, vol. 89, pp.27–38.
28. R. D. Pehlke, A. Jeyarajan and H. Wada: Summary of Thermal Properties For Casting Alloys and Mold Materials, University of Michigan, Ann Arbor, 1982, pp. 53-60.
29. N. Koker, G. Steinle-Neumann and V. Vlcek: Proc. Natl. Acad. Sci., 2012, vol. 109, pp. 4070-73.10.1073/pnas.1111841109 ↗
30. Y. S. Touloukian: Thermophysical properties of high temperature solid materials, Macmillan, New York,, 1967, pp. 1344-1352.
31. K. Ho and R. D. Pehlke: Trans. AFS, 1984, vol. 92, pp. 587-98.
32. K. H. Spitzer: Int. J. Heat Mass Transf., 1991, vol. 34, pp. 1969-74.10.1016/0017-9310(91)90208-V ↗
33. F. Lau, W. B. Lee, S. M. Xiong and B. C. Liu: J Mat. Proc. Tech., 1998, vol. 79, pp. 25-29.10.1016/S0924-0136(97)00449-4 ↗
34. L. J. D. Sully: Trans. AFS, 1976, vol. 84, pp. 735–44.
35. F. Chiesa: Trans. AFS, 1990, vol. 98, pp. 193-200.
36. C. P. Hallam and W. D. Griffiths: Metall. Mater. Trans. B, 2004, vol. 35, pp. 721-33.10.1007/s11663-004-0012-x ↗
37. S. Harmand, J. Pellé, S. Poncet and I. V. Shevchuk: Int. J. Therm. Sci., 2013, vol. 67, pp. 1-30.10.1016/j.ijthermalsci.2012.11.009 ↗