journal article·2007-06Open access

Machinability of Green Powder Metallurgy Components: Part II. Sintered Properties of Components Machined in Green State

Etienne Robert-Perron, Carl Blais, Sylvain Pelletier, Yannig Thomas

Abstract

The green machining process is virtually a must if the powder metallurgy (PM) industries are to solve the lower machining performances associated with PM components. This process is known for lowering the rate of tool wear. Recent improvements in binder/lubricant technologies have led to high-green-strength systems that enable green machining. Combined with the optimized cutting parameters determined in Part I of the study, the green machining of PM components seems to be a viable process for fabricating high performance parts on large scale and complete other shaping processes. This second part of our study presents a comparison between the machining behaviors and the sintered properties of components machined prior to or after sintering. The results show that the radial crush strength measured on rings machined in their green state is equal to that of parts machined after sintering.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Powder Metallurgy Techniques and Materials · Injection Molding Process and Properties · Advanced machining processes and optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. R.M. German: Powder Metallurgy and Particulate Processing, Metal Powder Industries Federation, Princeton, NJ, 2005, pp. 335–68
2. A. Salak, M. Selecka, and H. Danninger: Machinability of Powder Metallurgy Steels, Cambridge International Science Publishing, Cambridge, United Kingdom, 2005, pp. 1–4, 393–98
3. D.S. Madan: Adv. Powder Metall. Part. Mater., 1995, Part 8, pp. 55–67
4. R.J. Causton: Adv. Powder Metall. Part. Mater., 1995, Part 8, pp. 149–70
5. J.S. Agapiou, M.F. DeVeries: Int. J. Powder. Metall., 1988, vol. 24 (1), pp. 47–57
6. J.L. Seefelt, D.W. Smith, P. Machmeier: Adv. Powder Metall. Part. Mater., 1990, vol. 1, pp. 323–40
7. C. Blais, G. L’Espérance, I. Bourgeois: Powder Metall., 2001, vol. 44, pp. 67–7610.1179/003258901666194 ↗
8. K.S. Chopra: Adv. Powder Metall. Part. Mater., 1988, pp. 361–79
9. U. Engström: Powder Metall., 1983, vol. 26, pp. 137–4410.1179/pom.1983.26.3.137 ↗
10. L. Jiang, K. Cui, H. Hänninen: J. Mater. Process. Technol., 1996, vol. 58, pp. 160–6510.1016/0924-0136(95)02144-2 ↗
11. A. Benner and P. Beiss: Adv. Powder Metall. Part. Mater., 2001, Part 6, pp. 1–15
12. A. Benner and P. Beiss: Euro PM2000 Conf. on Material and Processing Trends for PM Components in Transportation Proc., European Powder Metallurgy Association (EPMA), Vienna, 2000, pp. 101–09
13. O. Andersson and A. Benner: Adv. Powder Metall. Part. Mater., 2001, Part 6, pp. 16–28
14. M. Ramstedt, O. Andersson, H. Vidarsson, and B. Hu: Adv. Powder Metall. Part. Mater., 2001, Part 12, pp. 151–62
15. O. Andersson and A. Benner: Adv. Powder Metall. Part. Mater., 2001, Part 6, pp. 16–28
16. E. Robert-Perron, C. Blais, Y. Thomas, S. Pelletier, M. Dionne: Mater. Sci. Eng. A-Struct., 2005, vol. 402, pp. 325–3410.1016/j.msea.2005.05.019 ↗
17. E. Robert-Perron, C. Blais, Y. Thomas, and S. Pelletier: Université Laval, Québec, unpublished research, 2006
18. Standard 35, Metal Powder Industries Federation, Princeton, NJ, 1998
19. Kennametal: Lathe Tooling, catalogue 1010, Latrobe, PA, 2001, 358 pp
20. C. Blais, G. L’Espérance: Powder Metall., 2002, vol. 45, pp. 39–4710.1179/003258902225001597 ↗
21. J. Campbell-Tremblay, C. Blais, G. L’Espérance, and P. Boilard: Adv. Powder Metall. Part. Mater., 2005, part 10, pp. 150–59
22. Mitutoyo: Surface Finish Tester SJ-201P User’s Manual, no. 99MBB079A, series no. 178
23. Standard 55, Metal Powder Industries Federation, Princeton, NJ, 1998