journal article·2013-12

Influence of CO2-Ar Mixtures as Shielding Gas on Laser Welding of Al-Mg Alloys

Zouhair Boukha, José María Sánchez-Amaya, Leandro González-Rovira, Eloy Del Rio, Ginesa Blanco, Javier Botana

Publisher page

Abstract

In this study, AA5083 samples were butt welded under a conduction regime with high-power diode laser (HPDL). Various mixtures composed of Ar and CO2 were used as a shielding gas. The influence of the shielding gas composition on the microstructure and on the properties of laser welds was analyzed. The weld beads were deeply characterized by metallographic/micro- structural studies, X-ray diffraction (XRD), X-ray energy dispersive spectrometry (X-EDS) chemical analyses, X-ray photoelectron spectra (XPS), microhardness, and tensile strength. The corrosion resistance of laser-remelted surfaces with different CO2/Ar ratios was also estimated by means of electrochemical tests. The addition of CO2 to the shielding gas results in a better weld penetration and oxidizes the weld pool surface. This addition also promotes the migration of Mg toward the surface of weld beads and induces the formation of magnesium aluminates spinel on the welds. The best corrosion resistance result is achieved with 20 pct CO2. The overall results indicate that the addition of small percentage of CO2 to Ar leads to improvements of the mechanical and corrosion properties of the aluminum welds.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis · Corrosion Behavior and Inhibition

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (57)

Show source-provided references
1. J.M. Sánchez-Amaya, M.R. Amaya-Vázquez, and F.J. Botana: Handbook of Laser Welding Technologies, 1st ed., Woodhead Publishing, Cambridge, U.K., 2013, pp. 215–8.10.1533/9780857098771.2.215 ↗
2. F. Matsuda and K. Nakata: Trans. JWRI., 1995, vol. 24, no. 1, pp. 83–94.
3. W. van Haver, X. Stassart, J. Verwimp, B. De Meester, and A. Dhooge: Weld. World, 2006, vol. 50 (11–12), pp. 65–77.10.1007/BF03263463 ↗
4. U. Dilthey, A. Brandenburg, and F. Reich: Weld. World, 2006, vol. 50 (7–8), pp. 7–10.10.1007/BF03266530 ↗
5. F.S. Bayraktar and P.S. Staron: Weld. World, 2007, vol. 51 (1–2), pp. 28–34.10.1007/BF03266543 ↗
6. H. Zhao and T. DebRoy: Metall. Mater. Trans. B, 2001, vol. 32B, pp. 163–72.10.1007/s11663-001-0018-6 ↗
7. Y. Shi, F. Zhonga, X. Li, S. Gong, and L. Chen: Mater. Sci. Eng. A, 2007, vol. 465, pp. 153–9.10.1016/j.msea.2007.02.079 ↗
8. P. Bassani, E. Capello, D. Colombo, B. Previtali, and M. Vedani: Compos. Part. A, 2007, vol. 38, pp. 1089–98.10.1016/j.compositesa.2006.04.014 ↗
9. R. Spina, L. Tricarico, G. Basile, and T. Sibillano: J. Mater. Proc. Tech., 2007, vol. 191, pp. 215–9.10.1016/j.jmatprotec.2007.03.087 ↗
10. A. Ancona, T. Sibillano, L. Tricarico, R. Spina, P.M. Lugara, G. Basile, and S. Schiavone: J. Mater. Proc. Tech., 2005, vols. 164-5, pp. 971–7.10.1016/j.jmatprotec.2005.02.048 ↗
11. T. Sibillano, A. Ancona, V. Berardia, E. Schingaro, G. Basilea, and P.M. Lugara: Opt. Lasers Eng., 2006, vol. 44, pp. 1039–51.10.1016/j.optlaseng.2005.09.002 ↗
12. L. Tricarico, R. Spina, D. Sorgente, A. Ancona, T. Sibillano, and G. Basile: Key Eng. Mater., 2007, vol. 344, pp. 745–50.10.4028/www.scientific.net/KEM.344.745 ↗
13. A. Haboudou, P. Peyre, A.B. Vannes, and G. Peix: Mater. Sci. Eng. A, 2003, vol. 363, pp. 40–52.10.1016/S0921-5093(03)00637-3 ↗
14. E. AssunÇao, S. Williams, and D. Yapp: Opt. Lasers Eng., 2012, vol. 50, pp. 823–8.10.1016/j.optlaseng.2012.02.001 ↗
15. R. Akhter, L. Ivanchev, and H.P. Burger: Mater. Sci. Eng. A, 2007, vol. 447, pp. 192–6.10.1016/j.msea.2006.10.148 ↗
16. J.M. Sánchez-Amaya, T. Delgado, J.J. De Damborenea, V. López, and F.J. Botana: Sci. Technol. Weld. Joi., 2009, vol. 14, no. 1, pp. 78–86.10.1179/136217108X347629 ↗
17. J.M. Sánchez-Amaya, T. Delgado, L. González-Rovira, and F.J. Botana: Appl. Surf. Sci., 2009, vol. 255, no. 23, pp. 9512–21.10.1016/j.apsusc.2009.07.081 ↗
18. N. Abe, M. Tsukamoto, K. Maeda, K. Namba, and J. Morimoto: J. Laser Appl., 2006, vol. 18, no. 4, pp. 289–93.10.2351/1.2227006 ↗
19. K. Howard, S. Lawson, and Y. Zhou: Weld. J., 2006, vol. 85, no. 5, pp. 101–10.
20. J.M. Sánchez-Amaya, Z. Boukha, L. González-Rovira, J. Navas, J. Martín-Calleja, and F.J. Botana: J. Laser Appl., 2012, vol. 24, no. 1, pp. 012002–9.10.2351/1.3659991 ↗
21. J.M. Sánchez-Amaya, Z. Boukha, M.R. Amaya-Vázquez, and F.J. Botana: Weld. J., 2012, vol. 91, no. 5, pp. 155–61.
22. T. Nacey: Weld. J., 2001, vol. 6, pp. 28–30.
23. L. Li: Opt. Laser. Eng., 2000, vol. 34, pp. 231–53.10.1016/S0143-8166(00)00066-X ↗
24. H. Wang, Y. Shi, S. Gong, and A. Duan: J. Mater. Process. Tech., 2007, vol. 184, pp. 379–85.10.1016/j.jmatprotec.2006.12.014 ↗
25. E. Akman, A. Demir, T. Canel, and T. Sınmazcelik: J. Mater. Process. Tech., 2009, vol. 209, pp. 3705–13.10.1016/j.jmatprotec.2008.08.026 ↗
26. L. Shanping, F. Hidetoshi, and N. Kiyoshi: ISIJ Int., 2005, vol. 45, no. 1, pp. 66–70.10.2355/isijinternational.45.66 ↗
27. B.E. Paton: Avtom. Svarka., 1974, vol. 6, pp. 1–7.
28. W.S. Bennett and G.S. Mills: Weld. J., 1974, vol. 53, pp. 548–53.
29. B.G. Chung, S. Rhee, and C.H. Lee: Mater. Sci. Eng. A-Struct., 1999, vol. 272, no. 2, pp. 357–62.10.1016/S0921-5093(99)00499-2 ↗
30. S. Katayama, H. Nagayama, M. Mizutani, and Y. Kawahito: Weld. Int., 2009, vol. 23, no. 10, pp. 744–52.10.1080/09507110902836911 ↗
31. A. Matsunawa, S. Katayama, and K. Kojima: Weld. Res. Abroad, 1999, vol. 45, no. 8, pp. 2–11.
32. G. Tani, A. Ascari, G. Campana, and A. Fortunato: Appl. Surf. Sci., 2007, vol. 254, no. 4, pp. 904–7.10.1016/j.apsusc.2007.08.067 ↗
33. W.F. Savage, E.F. Nippes, and G.M. Goodwin: Weld. J., 1977, vol. 56, pp. 126–32.
34. C.R. Heiple and J.R. Roper: Weld. J., 1981, vol. 60, pp. 143–5.
35. Y. Takeuchi, R. Takagi, and T. Shinoda: Weld. J., 1992, vol. 71, pp. 283–9.
36. D.H. Abbott and C.E. Albright: J. Laser. Appl., 1994, vol. 6, no. 2, pp. 69–80.10.2351/1.4745339 ↗
37. L. Shanping, F. Hidetoshi, and N. Kiyoshi: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 2861–7.
38. M.J. Tobar, I.M. Lamas, A. Yáñez, J.M. Sánchez-Amaya, Z. Boukha, and F.J. Botana: Phys. Procedia, 2010, vol. 5, no. 2, pp. 299–308.10.1016/j.phpro.2010.08.056 ↗
39. J.M. Sánchez-Amaya, Z. Boukha, M.R. Amaya-Vázquez, L. González-Rovira, and F.J. Botana: Mater. Sci. Forum, 2012, vol. 713, pp. 7–12.10.4028/www.scientific.net/MSF.713.7 ↗
40. J.M. Sánchez-Amaya, Z. Boukha, L. González-Rovira, M.R. Amaya-Vázquez, and F.J. Botana: Adv. Mater. Res., 2012, vol. 498, pp. 37–42.10.4028/www.scientific.net/AMR.498.37 ↗
41. ASTM E-384, “Standard Test Method for Micro-indentation Hardness of Materials”, 1999.
42. M. Mohai: Surf. Interface Anal., 2004, vol. 36, pp. 828–32.10.1002/sia.1775 ↗
43. C.J. Powell and A. Jablonski: NIST Electron-Effective-Attenuation Length Database, Version 1.3, SRD 82, National Institute of Standards and Technology, Gaithersburg, MD, 2011, pp. 24–25.
44. M. Tsuji, T. Yamamoto, Y. Tamaura, T. Kodama, and Y. Kitayama: Appl. Catal. A: Gen., 1996, vol. 142, pp. 31–45.10.1016/0926-860X(96)00050-6 ↗
45. C.R. Heiple and J.R. Roper: Weld. J., 1982, vol. 61, pp. 97–102.
46. A. Aballe, M. Bethencourt, F.J. Botana, M. Marcos, and J.M. Sánchez-Amaya: Corros. Sci., 2004, vol. 46, pp. 1909–20.10.1016/j.corsci.2003.10.028 ↗
47. A. Aballe, M. Bethencourt, F.J. Botana, M.J. Cano, and M. Marcos: Corros. Sci., 2001, vol. 43, pp. 1657–74.10.1016/S0010-938X(00)00166-9 ↗
48. R. Naghizadeha, H.R. Rezaie, and F. Golestani-Fard: Ceram. Int., 2011, vol. 37, no. 1, pp. 349–54.10.1016/j.ceramint.2010.09.016 ↗
49. B.R. Strohmeier: Surf. Interf. Anal., 1990, vol. 15, pp. 51–6.10.1002/sia.740150109 ↗
50. S.O. Saied and J.L. Sullivan: J. Phys. Condens. Mater., 1993, vol. 5, pp. 165–6.10.1088/0953-8984/5/33A/043 ↗
51. J.M. Sánchez-Amaya, G. Blanco, F.J. Garcia-Garcia, M. Bethencourt, and F.J. Botana: Surf. Coat. Tech., 2012, vol. 213, pp. 105–16.10.1016/j.surfcoat.2012.10.027 ↗
52. F.J. Garcia-Garcia, E.V. Koroleva, G.E. Thompson, and G.C. Smith: Surf. Interface Anal., 2010, vol. 42, pp. 258–63.10.1002/sia.3137 ↗
53. P. Sahoo, T. DebRoy, and M.J. McNallan: Metall. Trans. B., 1988, vol. 19B, pp. 483–91.10.1007/BF02657748 ↗
54. K. Ishizaki, N. Araki, and H. Murai: J. Jpn. Weld. Soc., 1965, vol. 34, pp. 146–53.10.2207/qjjws1943.34.146 ↗
55. L. Shanping, F. Hidetoshi, and N. Kiyoshi: J. Mater. Sci., 2005, vol. 40, pp. 2481–5.10.1007/s10853-005-1979-7 ↗
56. L. Shanping, F. Hidetoshi, T. Manabu, and N. Kiyoshi: Trans. JWRI., 2004, vol. 33, no. 1, pp. 5–9.
57. S. Hassanifard and M. Zehsaz: Procedia Eng., 2010, vol. 2, pp. 1077–85.10.1016/j.proeng.2010.03.116 ↗