journal article·2020-09Open access

Development of New Preheating Methods for Hot Forging Tools Based on Industrial Case Studies and Numerical Modeling

Marek Hawryluk, Paweł Widomski, Marcin Kaszuba, Jakub Krawczyk

Abstract

Abstract The study performs an overview and evaluation of the currently applied methods of preheating forging tools used in hot die forging processes performed on presses and presents the development and tests of new, more effective methods. Based on the conducted complex analysis of the temperature changes taking place on and directly beneath the surface of forging dies during their preliminary heating, an analysis was performed of one of the most commonly used methods of tool heating, i.e., using a charge material and a waste material. Next, the study proposes the introduction of changes and improvements of this method to achieve repeatability and stability of the obtained temperatures. To that end, detailed guidelines concerning the manner and time of the heating process were elaborated. The following step was the development of a new, more effective heating method. The first draft involved a new concept of heating using heaters localized in the die’s housing or heaters in the shape of forgings placed between the dies. Both concepts of heating were numerically modeled, which made it possible to assess their effectiveness. The last step of the research was the development of a heating method using induction heaters. This method was the most effective and brought the best results, which was confirmed during the modeling of the heating process and in the tests conducted on the prototype test stand. The obtained results confirm the effectiveness of almost all the methods, especially the method of heating by means of a charge material, supported by new guidelines, the method of heating with the use of forging-shaped heaters and the method of induction heating. Only in the case of heating with heaters mounted in the tool housing was the assumed working temperature not achieved. Some differences were observed mainly related to efficiency, that is, the heating speed in respect to the assumed temperature. The performed tests showed that the best method is induction heating as it is over twice as fast. Therefore, it is usually recommended for the process of heating and the additional heating realized in the work center of the press on the mounted tools, where the time aspect is especially important.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Induction Heating and Inverter Technology · Metallurgy and Material Forming · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. Z. Gronostajski, Z. Pater, L. Madej, A. Gontarz, L. Lisiecki, A. Lukaszek-Solek, J. Luksza, J. Mróz, Z. Muskalski, W. Muzykiewicz, M. Pietrzyk, R.E. Śliwa, J. Tomczak, S. Wiewiórowska, G. Winiarski, J. Zasadziński, S. Ziółkiewicz:Arch. Civ. Mech. Eng., 2019, vol. 19,pp. 898–941.
2. Forging Business Outlook, https://www.forgingmagazine.com/issues-and-ideas/2019-forging-business-outlook. Accessed 26 November 2019.
3. B.-A. Behrens, A. Bouguecha, M. Vucetic, A. Chugreev: Advanced Wear Simulation for Bulk Metal Forming Processes. MATEC Web of Conferences, 2016, 80, 1–4.10.1051/matecconf/20168004003 ↗
4. A.K.Singh: Wear, 1973, vol. 25, pp. 271-279.10.1016/0043-1648(73)90077-X ↗
5. R. Sharma and D.J. Arrowsmith: Wear, 1981, vol. 74, pp. 1-10.10.1016/0043-1648(81)90190-3 ↗
6. E. Summerville, K. Venkatesan, C. Subramanian: Materials&Design, 1995, vol. 16, pp. 289-294.10.1016/0261-3069(96)00010-6 ↗
7. M. Hawryluk: Arch. Civ. Mech. Eng, 2016, vol. 16, pp. 845–866.10.1016/j.acme.2016.06.001 ↗
8. M. Hawryluk,Z. Gronostajski,M. Kaszuba, S. Polak, P. Widomski, J. Smolik, J. Ziemba: Int. J. Mach. Tools Manuf., 2017, vol. 114, pp. 60-71.10.1016/j.ijmachtools.2016.12.010 ↗
9. M. Hawryluk, P. Widomski,J. Ziemba: Obróbka Plastyczna Metali = Metal Forming, 2017, vol. 28, pp. 75-92.
10. D. J. Politis, N. J. Politis, J. Lin, T. A. Dean: Int. J. Adv. Manuf. Technol., 2018, vol. 97, pp. 2809-33.10.1007/s00170-018-2151-2 ↗
11. H-W. Brockhaus, A. Guderjahn, I. Schruff, improving the performance of forging tools — a case study. https://www5.kau.se/sites/default/files/Dokument/subpage/2010/02/9_113_128_pdf_16762.pdf. Accessed 26 November 2019.
12. The Three Essential Forging Temperatures. https://www.williamsonir.com/blog/the-3-essential-forging-temperatures/. Accessed 26 November 2019.
13. Simulation of die heating for forgings and pressure castings by convective heating systems. https://mhi-inc.com/PG2/Die%20Heating%20Comparison%20Airtorch%20vs.%20Flame.PDF.Accessed 26 November 2019.
14. P. Widomski, M. Skwarski, M. Rychlik:Interdisciplinary Journal of Engineering Sciences, 2017, vol. V, http://ijes.pwr.wroc.pl
15. C. A. Blue, V. K. Sikka, E. K. Ohriner, P. G. Engleman, G. F. Mochnal, A. Underys, W-T. Wu, M. C. Maguire, R. Mayer: Infrared Heating Of Forging Billets And Dies.https://www.dykast.com/user/files/A_Forged_IinfraredHeatingReport1.pdf. Accessed 26 November 2019.
16. Z. Gronostajski, M. Hawryluk, J. Wollmann, M. Kaszuba, G. Misiun, P. Sadowski:Arch. Metall. Mater., 2015, vol. 60, pp. 2773-81.10.1515/amm-2015-0446 ↗
17. M.A. Kellow, A.N. Bramley, F.K. Bannister: International Journal of Machine Tool Design and Research, 1969, vol. 9, pp. 239-260.10.1016/0020-7357(69)90002-X ↗
18. Hot Die and Isothermal Forging. https://www.forging.org/forging/design/5224-hot-die-and-isothermal-forging.html. Accessed 26 November 2019.
19. US Patent US20150013421A1, Method for heating forging die device, 2012.
20. US Patent no WO2015167407A1, Forging dies with internal heating system, 2015.
21. M. Sawamura, Y. Yogo, S. Kondo, T. Tanaka, K. Nakanishi, T. Suzuki, A. Watanabe: R & D Review of Toyota CRDL, 2005, vol. 40, 50–56
22. T. Tanaka, K. Nakanishi, Y. Yogo, S. Kondo, T. Y. Tsuchiya, A. Watanabe: R & D Review of Toyota CRDL, 2005, 40, 1
23. K. Lange: Handbook of Metal Forming. Society of Manufacturing Engineers, Dearborn, 1985.
24. T. Altan: Metal Forming Handbook. Springer-Verlag Berlin Heidelberg New York, 1998, ISBN 3-540-61185-1
25. T. Altan, M. Shirgaokar, Advanced die materials and lubrication systems to reduce die wear in hot and warm forging, https://www.forging.org/uploaded/content/media/AltansPres.pdf. Accessed 26 November 2019.
26. B.-A. Behrens, J. Puppa, A. Huskic, K. Brunotte, A. Bouguecha, T. Prüß: Production Engineering, 2016, vol. 10, pp. 599-606.10.1007/s11740-016-0698-z ↗
27. B.-A. Behrens, R. Lachmayer, I. Malik, M. Bonhage, B. Sauthoff, P. Gottwald:WT Werkstattstechnik, 2015. Vol. 105, pp. 692-696.10.37544/1436-4980-2015-10-28 ↗
28. K. Staples, V. Sarvepalli, M. Fu, J. A.Sekhar, US Patent 5,963, 709 Oct. 5 1999.
29. F.H. Jeddy, M. A. Jog, J. A. Sekhar, R. D. Markle, V. Sarvepalli, R. Burada:Adv. Mater. and Process., 1999, vol. 156, pp. 213-15
30. M. Fu, K. Staples, V. Sarvepalli, JOM, 1998, vol. 50, pp. 42-44.10.1007/s11837-998-0032-0 ↗
31. Preheating moulds and dies quickly, homogeneously and without damaging materials. https://www.metec-tradefair.com/en/News/Topics/Preheating_moulds_and_dies_quickly,_homogeneously_and_without_damaging_materials. Accessed 26 November 2019.
32. Evaluation of various methods to pre-heat of forging dies. http://www.michigantechame.com/sites/default/files/Evaluation%20of%20Various%20Methods%20to%20Pre-Heat%20Forging%20Dies.pdf. Accessed 26 November 2019.
33. Infrared Die Pre-Heaters. https://www.infraredheating.com/industrial-ovens/infrared-die-pre-heaters/. Accessed 26 November 2019.
34. I.L. Akaro: Kuznechno-Shtampovochnoe Proizvodstvo (Obrabotka Metallov Davleniem), 2003, vol. 5, pp.40-43.
35. B. Mueller, N. Gerth, I. Hamann, A. Fischer, T. Rädel, M. Gebauer, T. Töppel: Prozessoptimierung im Druckgießverfahren – Laserstrahlgeschmolzener Werkzeugeinsatz im Praxistest,Giesserei, 2013, vol. 100, pp. 34-41.
36. Z. Gronostajski, P. Widomski, M. Kaszuba, M. Zwierzchowski, A. Barełkowski:Rudy i Metale Nieżelazne, 2018, vol. 63, pp. 9-18.
37. L. A. Dobrzański: Metalowe materiały inżynierskie. Wydawnictwo Naukowo Techniczne, 2004.
38. B. Buchmayr, BHM Berg- und Hüttenmännische Monatsheft, 2017, vol. 162, pp. 88-93.10.1007/s00501-016-0566-3 ↗
39. S. Singh, K. Sorensen, T. Condra, Appl. Therm. Eng., 2016, vol. 107, pp. 612-624.10.1016/j.applthermaleng.2016.07.022 ↗
40. M. Rywotycki, Z. Malinowski, J. Falkus, K. Sołek, A. Szajding, K. Miłkowska-Piszczek, Arch. Metall. Mater., 2016, vol. 61, pp. 341–346.10.1515/amm-2016-0063 ↗
41. X. Fu, B. Wang, X. Tang, H. Ji, X. Zhu, Appl. Therm. Eng., 2017, vol. 114, pp. 1-9.10.1016/j.applthermaleng.2016.11.192 ↗
42. M. C. Song, Y. H. Moon,Appl. Therm. Eng., 2016,vol. 98,pp. 98-10910.1016/j.applthermaleng.2015.11.129 ↗