Evaluation of Microstructure at Interfaces of Welded Joint Between Low Alloy Steel and Stainless Steel
Source abstract
Abstract
In the present investigation, welded joints between low alloy steel and 304LN stainless steel were considered. The joints were fabricated using Inconel 152 and 182 as buttering materials. A thin layer of martensite, Type-I boundary, and Type-II boundary were revealed near the fusion boundary between low alloy steel and the buttering material. The polygonal grain structure and unmixed zone were found near the fusion boundary between the weld metal and austenitic stainless steel. During a uniaxial in situ deformation test in an SEM, it was revealed that crack initiation and propagation were through the buttering material. In this respect, the weld fabricated with the Inconel 152 buttering material exhibited better joint efficiency and a higher strain-hardening exponent than the joint produced with the Inconel 182 buttering material. The improved strength of the former joint was attributed to a fine grain structure, fine-scale distribution of complex carbide phases, and qualitatively high dislocation density within the Inconel 152 buttering material.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. P.K. Singh, V. Bhasin, K.K. Vaze, A.K. Ghosh, and H.S. Kushwaha: BARC Newsletter, 2008, vol. 299, pp. 2–18.
2. U. State, N. R. Commission, Office of Reactor N. Information Notice 2000-17: Crack in Weld Area of Reactor Coolant System Hot Leg Piping at V.C. Summer 2000
3. C.D. Lundin: Weld J., 1982, pp. 58s–63s.
4. J.N. Dupont, J.C. Lippold, and S.D. Kaiser: Welding Metallurgy and Weldability of Nickel Base Alloys. Wiley, Hoboken, NJ, 2009.10.1002/9780470500262 ↗
5. M. Sireesha, S.K. Albert, V. Shankar, and S. Sundaresan: J. Nucl. Mater., 2000, vol. 279, pp. 65–76.10.1016/S0022-3115(99)00275-5 ↗
6. A.M. Shariatpanahi and H. Farhangi: Adv. Mater. Res., 2009, vols. 83–86, pp. 449–56.10.4028/www.scientific.net/AMR.83-86.449 ↗
7. H. Xu, S. Fyfitch, P. Scott, M. Foucault, R. Kilian, and M. Winters: Resistance to Primary Water Stress Corrosion Cracking of Alloys 690, 52, and 152 in Pressurized Water Reactors (MRP-111), EPRI, Washington, DC, 2004.
8. M. Ghosh, R. Santosh, S.K. Das, G. Das, B. Mahato, J. Korody, S. Kumar, and P.K. Singh: Metall. Mater. Trans. A, 2015, vol. 46A, pp. 3555–68.10.1007/s11661-015-2930-4 ↗
9. C. Jang, J. Lee, J.K. Sung, and T.J. Eun: Int. J. Press. Vessel Pip., 2008, vol. 85, pp. 635–46.10.1016/j.ijpvp.2007.08.004 ↗
10. K.J. Choi, J.J. Kim, B.H. Lee, C.B. Bahn, and J.H. Kim: J. Nucl. Mater., 2013, vol. 441, pp. 493–502.10.1016/j.jnucmat.2013.07.003 ↗
11. G.J. Brentrup and J.N. DuPont: Weld J., 2013, vol. 92, pp. 72–79.
12. H. Ming, Z. Zhang, J. Wang, E.H. Han, and W. Ke: Mater. Charact., 2014 vol. 97, pp. 101–15.10.1016/j.matchar.2014.08.023 ↗
13. Q. Peng, H. Xue, J. Hou, K. Sakaguchi, Y. Takeda, J. Kuniya, and T. Shoji: Corros. Sci., 2011, vol. 53, pp. 4309–17.10.1016/j.corsci.2011.08.046 ↗
14. R. Nivas, P.K. Singh, G. Das, S.K. Das, S. Kumar, B. Mahato, K. Shivaprasad, and M. Ghosh: J. Manuf. Processes, 2017, vol. 25, pp. 274–83.10.1016/j.jmapro.2016.12.004 ↗
15. H. Ming, Z. Zhang, J. Wang, E.H. Han, P. Wang, and Z. Sun: Mater. Charact., 2017, vol. 123, pp. 233–43.10.1016/j.matchar.2016.11.029 ↗
16. Z. Sun: Int. J. Press. Vess. Pip., 1996, vol. 68, pp. 153–60.10.1016/0308-0161(94)00048-4 ↗
17. J. Ruge, C. Oestmann, I. Decker, and K. Iversen: Proc. Electron Laser Beam Weld, 1986, pp. 193–203.
18. K. Murti and S. Sundaresan: Weld J., 1985, vol. 64, pp. 327–34.
19. R. Mouginot and H. Hanninen: Microstructure of Ni-Base Alloy Dissimilar Metal Welds, Aalto University, Espoo, Finland, 2013.
20. G.E. Dieter: Mechanical Metallurgy, 4th ed., McGraw-Hill, New York, NY, 1976.
21. D.W. Rathod, S. Pandey, P.K. Singh, and S. Kumar: J. Nucl. Mater., 2017, vol. 493, pp. 412–25.10.1016/j.jnucmat.2017.06.038 ↗
22. R. Nivas, G. Das, S.K. Das, B. Hato, S. Kumar, K. Sivaprasad, and M. Ghosh: Metall. Mater. Trans. A, 2017, vol. 48A, p. 23045.
23. S.L. Jeng, H.T. Lee, T.Y. Kuo, K.C. Tsai, C.L. Chung, and J.Y. Huang: Mater. Des., 2015, vol. 87, pp. 920–31.10.1016/j.matdes.2015.08.100 ↗
24. C. Lu, Y. He, Z. Gao, J. Yang, W. Jin, and Z. Xie: J. Nucl. Mater., 2017, vol. 495, pp. 103–10.10.1016/j.jnucmat.2017.08.013 ↗
25. S. Wang, J. Ding, H. Ming, Z. Zhang, and J. Wang: Mater. Charact., 2015, vol. 100, pp. 50–60.10.1016/j.matchar.2014.12.007 ↗
26. D. Porter and K. Easterling: Phase Transformations in Metals and Alloys, Chapman and Hall, London, 1992, p. 439.10.1007/978-1-4899-3051-4 ↗
27. K. Suzuki, I. Kurihara, T. Sasaki, Y. Koyoma, and Y. Tanaka: Nucl. Eng. Des., 2001, vol. 206, pp. 261–77.10.1016/S0029-5493(00)00440-4 ↗
28. J.N. Dupont and C.S. Kusko: Weld J.-NY, 2007, vol. 86, p. 5110.1016/B978-2-294-04792-3.50011-9 ↗
29. T.G. Gooch: TWI Res. Bull., 1977, pp. 343–49
30. J. Gegner, A.A. Vasilyev, P. Wilbrandt, and M. Kaffenberger: Proc. Int. Conf. Materials Technology Model, 2012, pp. 261–87
31. Y.J. Wu: Hydrogen Related Disbanding of Weld Overlay of Corrosion Resistant Alloys, University of Alberta, Edmonton, AB Canada, 1993
32. T.W. Nelson, J.C. Lippold, and M.J. Mills: Sci. Technol. Weld. Join., 1998, vol. 3, pp. 249–5510.1179/stw.1998.3.5.249 ↗
33. H. Shah Hosseini, M. Shamanian, and A. Kermanpur: Mater. Charact., 2011, vol. 62, pp. 425–3110.1016/j.matchar.2011.02.003 ↗
34. J.N. DuPont, A.R. Marder, M.R. Notis, and C.V. Robino: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 2797–280610.1007/s11661-998-0320-x ↗
35. H. Naffakh, M. Shamanian, and F. Ashrafizadeh: J. Mater. Process. Technol., 2009, vol. 209, pp. 3628–3910.1016/j.jmatprotec.2008.08.019 ↗
36. N. Suutala: Metall. Trans. A, 1983, vol. 14A, pp. 191–9710.1007/BF02651615 ↗
37. J.W. Elmer, S.M. Allen, and T.W. Eagar: Metall. Trans. A, 1989, vol. 20A, pp. 2117–3110.1007/BF02650298 ↗
38. S. Kou: Weld. Metall., 2002
39. R.W. Messler: Principles of Welding: Processes, Physics, Chemistry, and Metallurgy, Wiley, Weinheim, 1999.10.1002/9783527617487 ↗
40. W. Baeslack, J.C. Lippold, and W.F. Savage: Weld. J., 1979, vol. 58, p. 168.
41. H. Ming, R. Zhu, Z. Zhang, J. Wang, E.H. Han, W. Ke, and M. Su: Mater. Sci. Eng. A, 2016, vol. 669, pp. 279–90.10.1016/j.msea.2016.05.101 ↗
42. A. Joseph, S.K. Rai, T. Jayakumar, and N. Murugan: Int. J. Press. Vess. Pip., 2005, vol. 82, pp. 700–0510.1016/j.ijpvp.2005.03.006 ↗
43. D.A. Hughes and N. Hansen: in Fractography, eds., R.D. Joseph, D.D. James, A.D. Deborah, J.F. Heather, M.C. George, and M.J. Diane, ASM International, Metals Park, OH, 1987, pp. 192–206
44. S. Kumar, P.K. Singh, K.N. Karn, and V. Bhasin: Fatig. Fract. Eng. Mater. Struct., 2017, vol. 40, pp. 190–20610.1111/ffe.12484 ↗
45. H.T. Lee and T.Y. Kuo: Sci. Technol. Weld. Join., 1999, vol. 4, pp. 94–10310.1179/136217199101537626 ↗