journal article·2018-06

Delamination of Pearlitic Steel Wires: The Defining Role of Prior-Drawing Microstructure

A. Durgaprasad, S. Giri, S. Lenka, Sudip Kumar Sarkar, Aniruddha Biswas, S. Kundu, S. Mishra, S. Chandra, R. D. Doherty, I. Samajdar

Publisher page

Abstract

This article reports the occasional (< 10 pct of the actual production) delamination of pearlitic wires subjected to a drawing strain of ~ 2.5. The original wire rods which exhibited post-drawing delamination had noticeably lower axial alignment of the pearlite: 22 ± 5 pct vs 34 ± 4 pct in the nondelaminated wires. Although all wires had similar through-thickness texture and stress gradients, delaminated wires had stronger gradients in composition and higher hardness across the ferrite–cementite interface. Carbide dissolution and formation of supersaturated ferrite were clearly correlated with delamination, which could be effectively mitigated by controlled laboratory annealing at 673 K. Direct observations on samples subjected to simple shear revealed significant differences in shear localizations. These were controlled by pearlite morphology and interlamellar spacing. Prior-drawing microstructure of coarse misaligned pearlite thus emerged as a critical factor in the wire drawing-induced delamination of the pearlitic wires.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Advanced Surface Polishing Techniques · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (52)

Show source-provided references
1. Y. Li, D. Raabe, M. Herbig, P. Choi, S. Goto, A. Kostka and H. Yarita: Phys. Rev. Lett., 2014, Vol. 113, 106104, pp. 1-5.
2. M. Zelin: Acta Mater., 2002, Vol. 50, pp. 4431-4447.10.1016/S1359-6454(02)00281-1 ↗
3. X. Zhang, A. Godfrey, X. Huang, N. Hansen, Q. Liu, Acta Mater., 2011, Vol. 59, pp. 3422-3430.10.1016/j.actamat.2011.02.017 ↗
4. C. Borchers and R. Kirchheim: Prog. Mater. Sci., 2016, Vol. 82, pp. 405–444.10.1016/j.pmatsci.2016.06.001 ↗
5. J. D. Embury and R. M. Fisher: Acta Metall., 1966, Vol. 14, pp. 147-159.10.1016/0001-6160(66)90296-3 ↗
6. G. Langford: Metall. Trans. A, 1970, Vol. 1, pp. 465-477.10.1007/BF02811557 ↗
7. J. Languillaume, G. Kapelski and B. Baudelet: Acta Mater., 1997, Vol. 45, pp. 1201-1212.10.1016/S1359-6454(96)00216-9 ↗
8. K. Hono, M. Ohnuma, M. Murayama, S. Nishida, A. Yoshie and T. Takahashi: Scr. Mater., 2001, Vol. 44, pp. 977–98310.1016/S1359-6462(00)00690-4 ↗
9. W. J. Nam, C. M. Bae, S. J. Oh and S. Kwon: Scr. Mater., 2000, Vol. 42, pp. 457–463.10.1016/S1359-6462(99)00372-3 ↗
10. S. Goto, R. Kirchheim, T. Al-Kassab and C. Borchers: Trans. Nonferrous Met. SOC. China, 2007, Vol. 17, pp. 1129-1138.10.1016/S1003-6326(07)60238-6 ↗
11. N. Maruyama, T. Tarui and H. Tashiro: Scr. Mater., 2002, Vol. 46, pp. 599-603.10.1016/S1359-6462(02)00037-4 ↗
12. Y. S. Yang and C. G. Park: Int. J Mod. Phy. B, 2008, Vol. 22, pp. 5471–5476.10.1142/S021797920805067X ↗
13. K. Shimizu and N. Kawabe: ISIJ Int., 2001, Vol. 41, pp. 183–191.10.2355/isijinternational.41.183 ↗
14. X. Hu, L. Wang, F. Fang, Z. Ma, Z. Xie and J. Jiang: J Mater Sci., 2013,Vol. 48, pp. 5528–5535.10.1007/s10853-013-7347-0 ↗
15. D.B. Park, E.G. Kang and W.J. Nam: J Mater. Proc. Tech., 2007, Vol. 187–188, pp. 178–181.10.1016/j.jmatprotec.2006.11.136 ↗
16. D. B. Park, J. W. Lee, Y. S. Lee, K. T. Park and W. J. Nam: Met. Mater. Int., 2009, Vol. 15, pp. 197-202.10.1007/s12540-009-0197-2 ↗
17. N. Guo, B. Song, B. Shu and Q. Liu: Acta Metall. Sin., 2015, Vol. 28, pp. 707-714.10.1007/s40195-015-0251-7 ↗
18. S. K. Lee, D. C. Ko and B. M. Kim: Mater. Des., 2009, Vol. 30, pp. 2919-2927.10.1016/j.matdes.2009.01.007 ↗
19. J.W. Lee, J.C. Lee, Y.S. Lee, K.T. Park and W.J. Nam: J Mater. Proc. Tech., 2009, Vol. 209, pp. 5300–5304.10.1016/j.jmatprotec.2009.03.019 ↗
20. M. Tanaka, H. Saito, M. Yasumaru and K. Higashida: Scr. Mater., 2016, Vol. 112, pp. 32-3610.1016/j.scriptamat.2015.09.004 ↗
21. H. M. Baek, S. K. Hwang, H. S. Joo, Y. T. Im, I. H. Son and C. M. Bae: Mater. Des., 2014, Vol. 62, pp. 137-14810.1016/j.matdes.2014.05.014 ↗
22. S.W. Joung, U.G.Kang, S.P.Hong, Y.W.Kim and W.J.Nam: Mater. Sci. Eng. A, 2013, Vol. 586, pp. 171-17710.1016/j.msea.2013.07.095 ↗
23. C. M. Bae, W. J. Nam and C. S. Lee: Scr. Mater., 1996, Vol. 35, pp. 641-646.10.1016/1359-6462(96)00183-2 ↗
24. A. Durgaprasad, Ph.D. Thesis, Dept. of Metallurgical Engineering and Materials Science, Indian Institute of Bombay, Mumbai, 2017.
25. A. Durgaprasad, S. Giri, S. Lenka, S. Kundu, S. Mishra, S. Chandra, R. D. Doherty and I. Samajdar, Acta Mater., 2017, Vol. 129, pp. 278-289.10.1016/j.actamat.2017.02.008 ↗
26. A. Durgaprasad, S. Giri, S. Lenka, S. Kundu, S. Mishra, S. Chandra, R. D. Doherty and I. Samajdar: Metall. Trans A., 2017, vol. 48, pp. 4583-4597.10.1007/s11661-017-4269-5 ↗
27. A. Durgaprasad, S. Giri, S. Lenka, S. Kundu, S. Mishra, S. Chandra, R. D. Doherty and I. Samajdar: “Microstructural Engineering in Eutectoid Steel: A Technological Possibility?”, Under review (Manuscript # E-TP-17-1040-A), Metallurgical and Materials Transaction A, 2017.
28. T. Z. Zhao, S. H. Zhang, G. L. Zhang, H. W. Song and M. Cheng: Mater. Des., 2014, Vol. 59, pp. 397-40510.1016/j.matdes.2014.03.029 ↗
29. P. Van Houtte, The “MTM-FHM” and “MTM-TAY” Software System - Version 2, Manual, Department of MME, KLU Leuven, Belgium, 1995.
30. HJ Bunge (2013) Texture Analysis in Materials Science: Mathematical Methods, Elsevier, Oxford.
31. P. Van Houtte P. and L. De Buyser: Acta Metall. Mater., 1993, Vol. 41, pp. 323.10.1016/0956-7151(93)90063-X ↗
32. Verlinden B, Driver J, Samajdar I, Doherty RD. Thermo-Mechanical Processing of Metallic Materials, 1st edition. Pergamon Materials Series, Elsevier, Oxford; 2007.
33. A. Borbely, J. H. Driver and T. Ungar: Acta Mater., 2000, Vol. 48, pp. 2005-2016.10.1016/S1359-6454(99)00457-7 ↗
34. T. Ungar, I. Dragomir, A. Revesz and A. Borbely: J. Appl. Cryst., 1999, Vol. 32, pp. 992 - 100210.1107/S0021889899009334 ↗
35. Aniruddha Biswas, Debasis Sen, Sudip Kumar Sarkar, Sarita, S. and David N. Seidman: Acta Mater., 2016, Vol. 116, pp. 219-23010.1016/j.actamat.2016.06.043 ↗
36. Aniruddha Biswas, Donald J. Siegel and David N. Seidman: Acta Mater., 2014, Vol. 75, pp. 322–336.10.1016/j.actamat.2014.05.001 ↗
37. T. Z. Zhao, G. L. Zhan, S. H. Zhang, L. Y. Zhang: J Iron Steel Res. Int., 2016, vol. 23, pp. 1206-1212.10.1016/S1006-706X(16)30177-7 ↗
38. L. Zhou, F. Fang, L. Wang, H. Chen, Z. Xie, J. Jiang: Mater. Sci. Eng. A, 2018, vol. 713, pp. 52–60.10.1016/j.msea.2017.12.055 ↗
39. VN Gridnev, VG Gavrilyuki, Y Dekhtyayr, YM Eshkov, PS Nizin, VG Prokope (1972) Phys. Stat. Sol. A 11:689-694.10.1002/pssa.2210140238 ↗
40. Y.J. Li, P. Choi, C. Borchers, S. Westerkamp, S. Goto, D. Raabe and R. Kirchheim: Acta Mater., 2011, Vol. 59, pp. 3965–3977.10.1016/j.actamat.2011.03.022 ↗
41. Y.J. Li, P. Choi, C. Borchers, Y. Z. Chen, S. Goto, D. Raabe and R. Kirchheim: Ultramicroscopy, 2011, Vol. 111, pp. 628–632.10.1016/j.ultramic.2010.11.010 ↗
42. J. Chakraborty, M. Ghosh, Rajeev Ranjan, G. Das, D. Das and S. Chandra: Phil. Mag., 2013, Vol. 93,pp. 4598-4616.10.1080/14786435.2013.838010 ↗
43. V. G. Gavriljuk: Mater Sci Eng. A., 2003, Vol. 345, pp. 81-89.10.1016/S0921-5093(02)00358-1 ↗
44. H. G. Read, W. T. Reynolds Jr, K. Hono and T. Tarui: Scr Mater., 1997, Vol. 37, pp. 1221-123010.1016/S1359-6462(97)00223-6 ↗
45. M. H. Hong, W. T. Reynolds Jr, T. Tarui and K. Hono: Metall. Mater Trans. A., 1999, Vol. 30, pp. 717-2710.1007/s11661-999-1003-y ↗
46. Y. Li, D. Raabe, M. Herbig, P. Choi, S. Goto, A. Kostka, H. Yarita, C. Borchers and R. Kirchheim: Phy Rev Let., 2014, Vol. 113, pp. 1-5.
47. C. Borchers, T. A. Kasaab, S. Goto and R. Kirchheim: Mater Sci Eng. A, 2009, Vol. 502, pp. 131-138.10.1016/j.msea.2008.10.018 ↗
48. C. A. Bronkhorst, E. K. Cerreta, Q. Xue, P. J. Maudlin, T. A. Mason and G. T. Gray, Int. J Plast, 2006, Vol. 22, pp. 1304-1335.10.1016/j.ijplas.2005.10.002 ↗
49. Y. Yang, F. Jiang, B. M. Zhou, X. M. Li, H. G. Zheng and Q. M. Zhang: Mater. Sci. Eng. A, 2011, Vol. 528, pp. 2787-2794.10.1016/j.msea.2010.12.053 ↗
50. N. Keskar, S. Mukherjee, K.V. Mani Krishna, D. Srivastava, G.K. Dey, P. Pant, R.D. Doherty and I. Samajdar: Acta Mater., 2014, Vol. 69, pp. 265–274.10.1016/j.actamat.2014.01.023 ↗
51. Jaiveer Singh, S. Mahesh, Shomic Roy, Gulshan Kumar, D. Srivastava, G.K. Dey, N. Saibaba and I. Samajdar: Acta Mater., 2017, Vol. 123, pp. 337-349.10.1016/j.actamat.2016.10.049 ↗
52. Gulshan Kumar, Sandip Balo, Ashish Dhoble, Jaiveer Singh, Ramesh Singh, D. Srivastava, G.K. Dey and I. Samajdar: Metall. Mater. Trans. A, 2017, Vol. 48, pp. 2844–2857.10.1007/s11661-017-4032-y ↗