journal article·2017-12

Microstructure Optimization of Dual-Phase Steels Using a Representative Volume Element and a Response Surface Method: Parametric Study

Tarek M. Belgasam, Hussein M. Zbib

Publisher page

Abstract

Dual-phase (DP) steels have received widespread attention for their low density and high strength. This low density is of value to the automotive industry for the weight reduction it offers and the attendant fuel savings and emission reductions. Recent studies on developing DP steels showed that the combination of strength/ductility could be significantly improved when changing the volume fraction and grain size of phases in the microstructure depending on microstructure properties. Consequently, DP steel manufacturers are interested in predicting microstructure properties and in optimizing microstructure design. In this work, a microstructure-based approach using representative volume elements (RVEs) was developed. The approach examined the flow behavior of DP steels using virtual tension tests with an RVE to identify specific mechanical properties. Microstructures with varied martensite and ferrite grain sizes, martensite volume fractions, carbon content, and morphologies were studied in 3D RVE approaches. The effect of these microstructure parameters on a combination of strength/ductility of DP steels was examined numerically using the finite element method by implementing a dislocation density-based elastic-plastic constitutive model, and a Response surface methodology to determine the optimum conditions for a required combination of strength/ductility. The results from the numerical simulations are compared with experimental results found in the literature. The developed methodology proves to be a powerful tool for studying the effect and interaction of key microstructural parameters on strength and ductility and thus can be used to identify optimum microstructural conditions.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (48)

Show source-provided references
1. J. Galan, L. Samek, P. Verleysen, K. Verbeken, and Y. Houbaert, Rev. Metal., 2008, vol. 48, pp. 118–131.10.3989/revmetalm.1158 ↗
2. M. Y. Demeri, Advanced High-Strength Steels: Science, Technology, and Applications, 1st ed., ASM International, Materials Park, Oh:, 2013, pp. 105-120.10.31399/asm.tb.ahsssta.9781627082792 ↗
3. A. Haldar, S. Suwas, and D. Bhattacharjee: Proceedings of the International Conference on Microstructure and Texture in Steels, Springer-Verlag London Ltd., Guildford, Surrey, 2009, pp. 484–86.10.1007/978-1-84882-454-6 ↗
4. V. H. Baltazar Hernandez, S. S. Nayak, and Y. Zhou: Metall. Mater. Trans., 2011, vol. 42, pp. 3115–3129.10.1007/s11661-011-0739-3 ↗
5. S. S. Hansen, J. Appl. Metalwork, 1982, vol.2, pp.107-118.10.1007/BF02834208 ↗
6. Z. Jiang, Z. Guan, and J. Lian, Mater. Sci. Eng. A, 1995, vol 190, pp. 55-64.10.1016/0921-5093(94)09594-M ↗
7. A. Ramazani, K. Mukherjee, U. Prahl, and W. Bleck, Comput. Mater. Sci., 2012, vol. 52, pp. 46–54.10.1016/j.commatsci.2011.05.041 ↗
8. N. K. Balliger and T. Gladman, Met. Sci., 1981, vol. 15, pp. 95–108.10.1179/030634581790426615 ↗
9. X. Sun, K. S. Choi, W. N. Liu, and M. A. Khaleel, Int. J. Plast., 2009, vol. 25, pp. 1888–1909.10.1016/j.ijplas.2008.12.012 ↗
10. J. Samei, D. E. Green, S. Golovashchenko, and A. Hassannejadasl, J. Mater. Eng. Perform., 2013, vol. 22, pp. 2080–2088.10.1007/s11665-012-0438-2 ↗
11. J. Samei, D. E. Green, and S. Golovashchenko, J. Manuf. Sci. Eng., 2014, vol. 136, pp. 1-6.
12. N. D. Beynon, S. Oliver, T. B. Jones, and G. Fourlaris, Mater. Sci. Technol., 2005, vol. 21, pp. 771–778.10.1179/174328405X41038 ↗
13. A. M. Sherman and R. G. Davies, Int. J. Fatigue, 1981, vol. 3, pp. 195–198.10.1016/0142-1123(81)90020-7 ↗
14. D. L. Bourell and A. Rizk, Acta Metall., 1983, vol. 31, pp. 609–617.10.1016/0001-6160(83)90051-2 ↗
15. M. Azuma, S. Goutianos, N. Hansen, G. Winther, and X. Huang, Mater. Sci. Technol., 2012, vol. 28, pp. 1092–1100.10.1179/1743284712Y.0000000006 ↗
16. S. Sodjit and V. Uthaisangsuk, Mater. Des., 2012, vol. 41, pp. 370–379.10.1016/j.matdes.2012.05.010 ↗
17. M. Amirmaleki, J. Samei, D. E. Green, I. van Riemsdijk, and L. Stewart, Mech. Mater., 2016, vol. 101, pp. 27–39.10.1016/j.mechmat.2016.07.011 ↗
18. F. M. Al-Abbasi and J. A. Nemes, Int. J. Mech. Sci., 2003, vol. 45, pp. 1449–1465.10.1016/j.ijmecsci.2003.10.007 ↗
19. S. A. Asgari, P. D. Hodgson, C. Yang, and B. F. Rolfe, Comput. Mater. Sci., 2009, vol. 45, pp. 860–866.10.1016/j.commatsci.2008.12.003 ↗
20. A. S. Khan, M. Baig, S.-H. Choi, H.-S. Yang, and X. Sun, Int. J. Plast., 2012, vol. 30, pp. 1–17.
21. S. Nemat-Nasser, Mech. Mater., 1999, vol. 31, pp. 493–523.10.1016/S0167-6636(98)00073-8 ↗
22. A. Ramazani, K. Mukherjee, H. Quade, U. Prahl, and W. Bleck, Mater. Sci. Eng. A, 2013, vol. 560, pp. 129–139.10.1016/j.msea.2012.09.046 ↗
23. V. Uthaisangsuk, U. Prahl, and W. Bleck, Eng. Fract. Mech., 2011, vol. 78, pp. 469–486.10.1016/j.engfracmech.2010.08.017 ↗
24. N. H. Abid, R. K. Abu Al-Rub, and A. N. Palazotto, Int. J. Solids Struct.,2017, Vol. 104–105, pp.8-24.10.1016/j.ijsolstr.2016.11.005 ↗
25. M. J. Deepu, H. Farivar, U. Prahl, and G. Phanikumar, IOP Conf. Ser. Mater. Sci. Eng., 2017, Vol. 192, pp. 1.
26. D. Gerbig, A. Srivastava, S. Osovski, L. G. Hector, and A. Bower, Int. J. Fract., 2017, vol 207, pp. 1-24.10.1007/s10704-017-0215-1 ↗
27. A. C. Lewis and A. B. Geltmacher, Scr. Mater., 2006, vol. 55, pp. 81–85.10.1016/j.scriptamat.2006.01.043 ↗
28. D. Brands, J. Schröder, D. Balzani, O. Dmitrieva, and D. Raabe, Appl. Math. Mech, 2011, vol. 11, pp. 503–504.
29. C. Douglas: Montgomery: Design and Analysis of Experiments, 7th ed., Wiley, Hoboken, NJ, 2008, pp. 478–545.
30. M. Delincé, Y. Bréchet, J. D. Embury, M. G. D. Geers, P. J. Jacques, and T. Pardoen, Acta Mater., 2007, vol. 55, pp. 2337–2350.10.1016/j.actamat.2006.11.029 ↗
31. M. Jafari, S. Ziaei-Rad, and N. Torabian, Metallogr. Microstruct. Anal., 2014, vol. 3, pp. 185–193.10.1007/s13632-014-0136-6 ↗
32. S. Krajewski and J. Nowacki, Arch. Civ. Mech. Eng., 2014, vol. 14, pp. 278–286.10.1016/j.acme.2013.10.002 ↗
33. S. K. Paul, Mater. Des., 2013, vol. 44, pp. 397–406.10.1016/j.matdes.2012.08.023 ↗
34. S. K. Paul, Mater. Des., 2013, vol. 50, pp. 782–789.10.1016/j.matdes.2013.03.096 ↗
35. C. C. Tasan, M. Diehl, D. Yan, M. Bechtold, F. Roters, L. Schemmann, C. Zheng, N. Peranio, D. Ponge, M. Koyama, K. Tsuzaki, and D. Raabe, Annu. Rev. Mater. Res., 2014, vol. 45, pp. 391-431.10.1146/annurev-matsci-070214-021103 ↗
36. D. Brands, D. Balzani, L. Scheunemann, J. Schröder, H. Richter, and D. Raabe, Arch. Appl. Mech., 2016, vol. 86, pp. 575–598.10.1007/s00419-015-1044-1 ↗
37. S.K. Paul: Model. Simul. Mater. Sci. Eng., 2013, vol. 21, pp. 55001(1–26).10.1088/0965-0393/21/5/055001 ↗
38. T. Mori and K. Tanaka, Acta Metall., 1973, vol. 21, pp. 571–574.10.1016/0001-6160(73)90064-3 ↗
39. R. M. Rodriguez and I. Gutiérrez, Mater. Sci. Forum, 2003, vol. 426–432, pp. 4525–4530.10.4028/www.scientific.net/MSF.426-432.4525 ↗
40. S. K. Paul and A. Kumar, Comput. Mater. Sci., 2012, vol. 63, pp. 66–74.10.1016/j.commatsci.2012.05.061 ↗
41. A. Ramazani, P. T. Pinard, S. Richter, A. Schwedt, and U. Prahl, Comput. Mater. Sci., 2013, vol. 80, pp. 134–141.10.1016/j.commatsci.2013.05.017 ↗
42. A. Ramazani, K. Mukherjee, A. Abdurakhmanov, U. Prahl, M. Schleser, U. Reisgen, and W. Bleck, Mater. Sci. Eng. A, 2014, vol. 589, pp. 1–14.10.1016/j.msea.2013.09.056 ↗
43. S. Sodjit and V. Uthaisangsuk, J. Met. Mater., 2012, vol. 22, pp. 87–97.
44. C. Thomser, V. Uthaisangsuk, and W. Bleck, Steel Res. Iner., 2009, vol. 80, pp. 582–587.
45. A. P. Pierman, O. Bouaziz, T. Pardoen, P. J. Jacques, and L. Brassart, Acta Mater., 2014, vol. 73, pp. 298–311.10.1016/j.actamat.2014.04.015 ↗
46. G.I., Metalurgija, 2012, vol. 11, pp. 201–14.
47. H. Öktem, T. Erzurumlu, and H. Kurtaran, J. Mater. Process. Technol., 2005, vol. 170, pp. 11–16.10.1016/j.jmatprotec.2005.04.096 ↗
48. M. Calcagnotto, D. Ponge, and D. Raabe, Mater. Sci. Eng. A, 2010, vol. 527, pp. 7832–7840.10.1016/j.msea.2010.08.062 ↗