Ductility exhaustion mechanisms in thermally exposed thin sheets of a near-β titanium alloy
Source abstract
Abstract
This study examines the effects of thermal exposure in air environment on the plastic elongation of thin sheets of Ti-15Mo-2.7Nb-3Al-0.2Si (Timetal-21S) alloy. Specimens with thicknesses of 0.12, 0.39, and 1.0 mm were exposed in air environment to temperatures ranging from 482 °C to 693 °C. Tensile tests conducted on these specimens at room temperature show a reduction of plastic elongation proportional to the thermal exposure parameters, time and temperature. Furthermore, a change in the failure mode into a quasi-brittle fracture was observed in the near-surface region. The depth of this region depends on both exposure time and temperature. The kinetics of embrittlement is studied through theoretical considerations of gas diffusion into metal. This approach shows that two distinct embrittlement mechanisms operate in this alloy. The characteristics of each of these mechanisms depend on the corresponding temperature range. At temperatures higher than 545 °C, the embrittlement activation energy is 41.2 kcal·mol−1, indicating that the embrittlement process is governed by an enhanced diffusion of oxygen into Timetal-21S. Below this transitional temperature, the embrittlement activation energy approaches zero, a characteristic of slow kinetics transformation. The effects of solid-solution hardening, precipitation-hardening mechanisms, and alloying-element partitioning on ductility exhaustion processes are analyzed and discussed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Intermetallics and Advanced Alloy Properties · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. P.J. Bania: in Beta Titanium Alloys in the 1990’s, D. Eylon, R.R. Boyer, and D.A. Koss, eds., TMS, Warrendale, PA, 1993, pp. 3–14.
2. R.W. Schutz: in Beta Titanium Alloys in the 1990’s. D. Eylon, R.R. Boyer, and D.A. Koss eds., TMS, Warrendale, PA, 1993, pp. 75–91.
3. T.A. Wallace, K.E. Wiedemann, and R.K. Clark: in Titanium ’92: Science and Technology, F.H. Froes and I. Caplan, eds., TMS, Warrendale, PA, 1993, pp. 2177–84.
4. T.A. Wallace, R.K. Bird, and K.E. Wiedemann: in Beta Titanium Alloys in the 1990’s, D. Eylon, R.R. Boyer, and D.A. Koss, eds., TMS, Warrendale, PA, 1993, pp. 115–26.
5. K.E. Wiedemann, R.K. Bird, T.A. Wallace, and R.K. Clark: in Titanium ’92: Science and Technology, F.H. Froes and I. Caplan, eds., TMS, Warrendale, PA, 1993.
6. W. M. Parris and P.J. Bania: in Titanium ’92 Science and Technology, F.H. Froes, and I.L. Caplan, eds., TMS, Warrendale, PA, 1993, pp. 153–60.
7. X. Huang, J. Cuddy, N. Goel, and N.L. Richards: J. Mater. Eng. Performance, 1994, vol. 3, pp. 560–66.10.1007/BF02645322 ↗
8. M. Almesallmy: Master’s Thesis, University of Rhode Island, Kingston, RI, 2001.
9. K. Chaudhuri and J.H. Perepezko: Metall. Mater. Trans. A, 1994, vol. 25A, pp. 1109–18.10.1007/BF02652286 ↗
10. J.C. Williams, R.R. Boyer, and M.J. Blackburn: ASTM STP 453, ASTM, Warrendale, PA, 1969, pp. 215–35.
11. D.C. Lagoudas, X. Ma, D.A. Miller, and D.H. Allen: Int. J. Eng. Sci., 1995, vol. 33 (15), pp. 2327–43.10.1016/0020-7225(95)00073-7 ↗
12. P.B. Entchev, D.C. Lagoudas, and J.C. Slattery: Int. J. Eng. Sci., 2001, vol. 39, pp. 695–714.10.1016/S0020-7225(00)00053-7 ↗
13. C. Schuh: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 2411–21.10.1007/s11661-000-0186-z ↗
14. W.J. Boettinger, M.E. Williams, S.R. Coriell, U.R. Kattner, and B.A. Mueller: Metall. Mater. Trans. B, 2000, 31B, pp. 1419–27.10.1007/s11663-000-0026-y ↗
15. J.E. Reynolds, H.R. Ogdren, and R.I. Jaffee: Trans. ASM, 1957, vol. 49, pp. 280–99.
16. D.A. Porter and K.E. Easterling: Acta Metall., 1978, vol. 26 (9), pp. 1405–22.10.1016/0001-6160(78)90156-6 ↗
17. J. Crank: The Mathematics of Diffusion, Clarendon Press, Oxford, United Kingdom, 1975.
18. W.P. Roe, H.R. Palmer, and W.R. Opie: Trans. ASM, 1960, vol. 52, pp. 191–200.
19. Z. Liu and G. Welsch: Metall. Trans. A, 1988, vol. 19A, pp. 1121–1510.10.1007/BF02628396 ↗
20. K.E. Wiedemann, R.N. Shenoy, and J. Unnam: Metall. Trans. A, 1987, vol. 18A, pp. 1503–10.10.1007/BF02646662 ↗
21. A.I. Kahveci and G. Welsch: Scripta Metall., 1986, vol. 20, pp. 1287–90.10.1016/0036-9748(86)90050-5 ↗
22. H. Dong and X.Y. Li: Mater. Sci. Eng., 2000, vol. A280, pp. 303–10.10.1016/S0921-5093(99)00697-8 ↗
23. L. Bendersky and A. Rosen: Eng. Fract. Mech., 1980, vol. 13, pp. 111–18.10.1016/0013-7944(80)90046-6 ↗
24. J. Unnam, R.N. Shenoy, and R.K. Clark: Oxid. Met., 1986, vol. 26, pp. 231–52.10.1007/BF00659186 ↗
25. D.J. Simbi and J.C. Scully: Mater. Lett., 1996, vol. 26, pp. 35–39.10.1016/0167-577X(95)00204-9 ↗
26. Z. Liu and G. Welsch: Metall. Trans. A, 1988, vol. 19A, pp. 527–42.10.1007/BF02649267 ↗
27. H. Kellerer and L. Wingert: Metall. Trans., 1971, vol. 2 (1), pp. 113–15.10.1007/BF02662644 ↗
28. J.C. Williams, B.S. Hickman, and D.H. Leslie: Metall. Trans., 1971, vol. 2 (1), pp. 477–84.10.1007/BF02663337 ↗
29. F.H. Froes, C.F. Yolton, J.M. Capenos, M.G.H. Wells, and J.C. Williams: Metall. Trans. A, 1980, vol. 11A, pp. 21–31.10.1007/BF02700435 ↗
30. E. Sukedai, H. Hashimoto, M. Hida, and H. Mabuchi: Mater. Sci. Technol., 1992, vol. 8, pp. 3–9.10.1179/026708392790169858 ↗
31. S. Ankem, D. Banerjee, D.J. McNeish, J.C. Williams, and S.R. Seagle: Metall. Trans. A, 1987, vol. 18A, pp. 2015–25.10.1007/BF02647074 ↗
32. S. Ankem and C.A. Greene: Mater. Sci. Eng., 1999, vol. A263, pp. 127–31.10.1016/S0921-5093(98)01170-8 ↗
33. G. Sridhar and D.S. Sarma: Metall. Trans. A, 1993, vol. 24A, pp. 21–31.
34. V. Chandrasekaran, R. Taggart, and D.H. Polonis: Mater. Characterization, 1997, vol. 39, pp. 183–98.10.1016/S1044-5803(97)00131-9 ↗
35. F.H. Froes, J.M. Capenos, and M.G.H. Wells: Titanium Science and Technology; proceedings, R.I. Jaffee and H.M. Burte, eds., Plenum Press, New York, NY, 1973, pp. 1621–33.
36. J.W. Hagemeyer and D.E. Gordon: in Titanium Science and Technology; Proceedings, R.I. Jaffee and H.M. Burte, eds., Plenum Press, New York, NY, 1973, pp. 1957–68.
37. D.E. Gordon and J.W. Hagemeyer: J. Mater. Sci., 1975, vol. 10, pp. 1725–31.10.1007/BF00554934 ↗