journal article·2018-04

Embrittlement of Intercritically Reheated Coarse Grain Heat-Affected Zone of ASTM4130 Steel

Liying Li, Tao Han, Bin Han

Publisher page

Abstract

In this investigation, a thermal welding simulation technique was used to investigate the microstructures and mechanical properties of the intercritically reheated coarse grain heat-affected zone (IR CGHAZ) of ASTM4130 steel. The effect of post weld heat treatment (PWHT) on the toughness of IR CGHAZ was also analyzed. The toughness of IR CGHAZ was measured by means of Charpy impact, and it is found that IR CGHAZ has the lowest toughness which is much lower than that of the base metal regardless of whether PWHT is applied or not. The as-welded IR CGHAZ is mainly composed of ferrite, martensite, and many blocky M–A constituents distributing along grain boundaries and subgrain boundaries in a near-connected network. Also, the prior austenite grains are still as coarse as those in the coarse grain heat-affected zone (CGHAZ). The presence of the blocky M–A constituents and the coarsened austenite grains result in the toughness deterioration of the as-welded IR CGHAZ. Most of the blocky M–A constituents are decomposed to granular bainite due to the effect of the PWHT. However, PWHT cannot refine the prior austenite grains. Thus, the low toughness of IR CGHAZ after PWHT can be attributed to two factors, i.e., the coarsened austenite grains, and the presence of the remaining M–A constituents and granular bainite, which are located at grain boundaries and subgrain boundaries in a near-connected network. The absorbed energy of the IR CGHAZ was increased by about 3.75 times, which means that the PWHT can effectively improve the toughness but it cannot be recovered to the level of base metal.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. J.R. Still and V. Blackwood: Weld. J., 1997, vol. 76(7), pp. 37–42.
2. L.Y. Lan, C.L. Qiu, D.W. Zhao, X.H. Gao, and L.X. Du: Mater. Sci. Technol., 2011, vol. 27, pp. 1657–63.10.1179/1743284710Y.0000000026 ↗
3. E. Bonnevie, G. Ferrière, A. Ikhlef, D. Kaplan, and J.M. Orain: Mater. Sci. Eng. A, 2004, vol. 385, pp. 352–58.10.1016/S0921-5093(04)00859-7 ↗
4. C.W. Li, Y. Wang, T. Han, B. Han, and L.Y. Li: J. Mater. Sci., 2011, vol. 46, pp. 727–33.10.1007/s10853-010-4803-y ↗
5. L.Y. Li, Y. Wang, T. Han, and C.W. Li: Sci. China-Phys. Mech. Astron., 2011, vol. 54(8), pp. 1447-54.10.1007/s11433-011-4401-2 ↗
6. C.L. Davis and J.E. King: Metall. Mater. Trans. A., 1994, vol. 25(3), pp. 563–73.10.1007/BF02651598 ↗
7. J.I. Jang, J.B. Ju, B.W. Lee, D. Kwon, and W.S. Kim: Mater. Sci. Eng. A, 2003, vol. 340, pp. 68–79.10.1016/S0921-5093(02)00190-9 ↗
8. C.W. Li, Y. Wang and Y.H. Chen: J. Mater. Sci., 2011, vol. 46, pp. 6424-31.10.1007/s10853-011-5592-7 ↗
9. H. Qiu, H. Mori, M. Enoki, and T. Kishi: Metall. Mater. Trans. A, 2000, vol. 31, pp. 2785-91.10.1007/BF02830338 ↗
10. K. Ohya, J. Kim, K. Yokoyama, and M. Nagumo: Metall. Mater. Trans. A., 1996, vol. 27, pp. 2574-82.10.1007/BF02652351 ↗
11. X. Wang, J.W. Chang, G.Z. Huang, and Y.L. Zhang: Trans. China Weld. Inst., 2008, vol. 29(10), pp. 29-32.
12. [V.G. Haugen, B.R.S. Rogne, O.M. Akselsen, C. Thaulow, and E. Østby: Mater. Design, 2014, vol. 59, pp. 135-40.10.1016/j.matdes.2014.02.010 ↗
13. Y. You, C.J. Shang, L. Chen, and S. Sundaresa: Mater. Design, 2013, vol. 43, pp. 485-91.10.1016/j.matdes.2012.07.015 ↗
14. F. Matsuda, K. Ikeuchi, Y. Fukada, Y. Horii, H. Okada, T. Shiwaku,C. Shiga, S. Suzuki: Trans. JWRI, 1995, vol. 24(1), pp. 1–24.
15. S.S. D’yachenko: Met. Sci. Heat Treat., 2000, vol. 42, pp. 122–7.10.1007/BF02471324 ↗
16. S.S. Yugai, L.M. Kleiner, A.A. Shatsov and N.N. Mitrokhovich: Met. Sci. Heat Treat., 2004, vol. 46, pp. 539-44.10.1007/s11041-005-0015-5 ↗
17. S. Lee, B.C. Kim, D. Kwon: Metall. Mater. Trans. A, 1992, vol. 23, pp. 2803-16.10.1007/BF02651759 ↗
18. B.C. Kim, S. Lee, N.J. Kim, and D.Y. Lee: Metall. Trans. A, 1991, vol. 22, pp. 139-49.10.1007/BF03350956 ↗
19. X.D. Li, Y.R. Fan, X.P. Mao, S.V. Subramanian and C.J. Shang: Mater Des, 2015, vol. 67, pp. 457-463.10.1016/j.matdes.2014.10.028 ↗
20. X.D. Li, C.J. Shang, X.P. Ma, B. Gault, S.V. Subramanian, J.B. Sun and R.D.K. Misra: Scripta Mater., 2017, vol. 139, pp. 67-70.10.1016/j.scriptamat.2017.06.017 ↗
21. A. Lambert, J. Drillet, A.F. Gourgues, T. Sturel, A. Pineau: Sci. Technol. Weld. Joining, 2000, vol. 5, pp. 168–73.10.1179/136217100101538164 ↗
22. ASM Handbook Volume 4: Heat Treating, ASM International®, p. 105.
23. ASM Handbook Volume 6: Welding, Brazing and Soldering, ASM International®, p. 1655.
24. Y.H. Li and F.H. Bao: Trans. China Weld. Inst., 1987, vol. 8(4), pp. 181-7.
25. Y.P. Kang: Metallic Solid-state Phase Transformation and Application, Chemical Industry Press, Beijing, 2007, pp. 27-30.
26. E. Bayraktar and D Kaplan: J. Mater. Process. Technol., 2004, vol. 153-154, pp. 87-92.10.1016/j.jmatprotec.2004.04.021 ↗
27. C.L. Davis and J.E. King: Metall. Mater. Trans. A, 1996, vol. 27, pp. 3019-29.10.1007/BF02663851 ↗
28. S. Moeinifar, A.H. Kokabi, and H.R. Madaah Hosseini: J. Mater. Process. Technol., 2011, vol. 211, pp. 368-75.10.1016/j.jmatprotec.2010.10.011 ↗
29. P. Mohseni, J.K. Solberg, M. Karlsen, O.M. Akselsen, and E. Østby: Metall. Mater. Trans. A., 2014, vol. 45, pp. 384-94.10.1007/s11661-013-2110-3 ↗
30. C.L. Davis, and J.E. King: Mater. Sci. Technol., 1993, vol. 9, pp. 8-15.10.1179/mst.1993.9.1.8 ↗
31. J.S. Liao, K. Ikeuchi, and F. Matsuda: Nucl. Eng. Des., 1998, vol. 183, pp. 9-20.10.1016/S0029-5493(98)00151-4 ↗
32. A. Lambert-Perlade, A.F. Gourgues, and A. Pineau: Acta Mater., 2004, vol. 52, pp. 2337-48.10.1016/j.actamat.2004.01.025 ↗
33. H.L. Gao, Y.H. Dong and Y.R. Feng: J. Mech. Eng., 2001, vol. 37(3), pp. 14-19.10.3901/JME.2001.03.014 ↗
34. X. Wang, J.W. Chang, F.Y. Chen and M.L. Qiu: Trans. China Weld. Inst., 2008, vol. 29(3), pp. 9-12.