journal article·2018-02

Solid Particle Erosion of Nanocrystalline Nickel Coatings: Influence of Grain Size and Adiabatic Shear Bands

Nitin P. Wasekar, Prathap Haridoss, G. Sundararajan

Publisher page

Abstract

The primary objective of the present study is to investigate the influence of nanocrystalline grain size on the solid particle erosion behavior of nickel. For the above purpose, 450-μm-thick nanocrystalline Ni coatings having the average grain sizes of 21, 42, 70, and 195 nm were obtained using pulsed electrodeposition (PED). All these samples along with bulk annealed Ni samples (43 μm grain size) were subjected to solid particle erosion using SiO2 particles as an erodent at a constant impact velocity of 45 m/s and two impact angles (30 and 90 deg). Erosion results indicate that bulk Ni and PED Ni coatings of grain sizes 195 and 70 nm exhibit the same erosion rate, while PED Ni coatings of 42 and 21 nm grain size exhibit marginally higher erosion rates with a clear trend of increasing erosion rate with decreasing grain size. It was also observed that the higher erosion rates exhibited by 21- and 42-nm-grain size PED Ni samples were associated with the formation of adiabatic shear bands (ASBs) originating from the eroded surface and propagating into the eroded sample. The experimental observations have been understood on the basis of a transition from a localization model for erosion for coarse-grained Ni (> 70 nm) to an ASB-induced erosion model for grain sizes less than 70 nm.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Erosion and Abrasive Machining · Advanced materials and composites · High-Temperature Coating Behaviors

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (50)

Show source-provided references
1. A. V. Levy: Wear, 1981, vol. 68, pp. 269-87.10.1016/0043-1648(81)90177-0 ↗
2. A.V. Reddy and G. Sundararajan: Tool and Alloy Steels, 1986, vol. 20, pp. 379-88.
3. T. Foley and A.V. Levy: Wear, 1983, vol. 91, 45-64.10.1016/0043-1648(83)90107-2 ↗
4. K.P. Balan, A. V. Reddy and G. Sundararajan: Wear, 1991, vol.145, pp. 283-96.10.1016/0043-1648(91)90136-I ↗
5. M. Roy, M. Subramanyam, G. Sundararajan: Tribology International, 1992, vol. 25, pp. 271-80.10.1016/0301-679X(92)90064-T ↗
6. D.R.K. Rao, B. Venkataraman, M.K. Asundi, G. Sundararajan: Scripta. Mater. 1992, vol. 27, pp. 937-42.10.1016/0956-716X(92)90420-J ↗
7. A.V. Levy, Z.R. Shui, B.Q. Wang: Wear, 1988, vol. 127, pp. 193-205.10.1016/0043-1648(88)90130-5 ↗
8. M. Roy, Y. Tirupataiah, G. Sundararajan: Mat. Sci. & Tech., 1995, vol. 11, pp. 791-97.10.1179/mst.1995.11.8.791 ↗
9. S. Yerramareddy and S. Bahadur : Wear, 1991, vol. 142, pp. 253-63.10.1016/0043-1648(91)90168-T ↗
10. N. Hansen: Scripta. Mater., 2004, vol. 51, pp. 801-806.10.1016/j.scriptamat.2004.06.002 ↗
11. A. V. Reddy and G. Sundararajan : Met. Trans., 1987, vol. 18A, pp. 1043-52.10.1007/BF02668553 ↗
12. A.M. El-Sherik, U. Erb, J. Page: Surf. Coat. Tech., 1996, vol. 88, pp. 70-78.10.1016/S0257-8972(96)02928-3 ↗
13. N.P. Wasekar, P. Haridoss, S.K. Seshadri, G. Sundararajan: Surf. Coat. Tech., 2016, vol. 291, pp. 130-40.10.1016/j.surfcoat.2016.02.024 ↗
14. A.J. Detor and C.A. Schuh: Acta. Mater., 2007, vol. 55, pp. 371-79.10.1016/j.actamat.2006.08.032 ↗
15. ASTM G76-13: Standard Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets, American Society for Testing and Materials, Philadelphia, USA, 2013.
16. S.A. Nasser, H.H. Afify, S.A. E-Hakim, M.K. Zayed : Thin Solid Films, 1998, vol. 315, pp. 327-35.10.1016/S0040-6090(97)00757-8 ↗
17. A.W. Thomas: Acta. Met., 1977, vol. 25, pp. 83-86.10.1016/0001-6160(77)90141-9 ↗
18. F. Ebrahimi, G.R. Bourne, M.S. Kelly, T.E. Mathews: Nanostruct. Mater., 1999, vol. 11, pp. 343-50.10.1016/S0965-9773(99)00050-1 ↗
19. N. Krasilnikov, W. Lojkowski, Z. Pakeila, R. Valiev : Mat. Sci. Engg. A, 2005, vol. 397, pp. 330-37.10.1016/j.msea.2005.03.001 ↗
20. F. Ebrahimi, Z. Ahmed, H.Q. Li: Mater. Manuf. Proc., 2006, vol. 21, pp. 687-93.10.1080/10426910600611748 ↗
21. P. S. Babu, B. Basu, G. Sundararajan: Acta. Mater., 2008, vol. 56, pp. 5012-26.10.1016/j.actamat.2008.06.023 ↗
22. K. L. Johnson: Contact Mechanics, Cambridge University Press, 1987.
23. W. Johnson, R. Sowerby, J.B. Haddow: Plane-Strain Slip-Line Fields, Theory and Bibliography, Edward Arnold, London. 1970.
24. G. Sundararajan: Wear, 1991, vol. 149, pp. 111-27.10.1016/0043-1648(91)90368-5 ↗
25. G. Sundararajan: Wear, 1995, vol. 186-187, pp. 129-44.10.1016/0043-1648(95)07172-5 ↗
26. G. Sundararajan and Y. Tirupataiah : Acta. Mater., 2006, vol. 54, pp. 565-75.10.1016/j.actamat.2005.09.022 ↗
27. G. Sundararajan and Y. Tirupataiah: Acta. Mater., 2006, vol. 54, pp. 577-86.10.1016/j.actamat.2005.09.021 ↗
28. K.G. Hoge and A.K. Mukherjee: J. Mater. Sci., 1977, vol. 12, pp. 1666-72.10.1007/BF00542818 ↗
29. Blazynski: Materials at High Strain Rates, Elsevier Applied Science Publishers Ltd. 1987.
30. R.E. Winter and I.M. Hutchings: Wear, 1975, vol. 34, pp. 141-48.10.1016/0043-1648(75)90060-5 ↗
31. S.P. Timothy and I.M. Hutchings: Acta. Met., 1985, vol. 33, pp. 667-76.10.1016/0001-6160(85)90030-6 ↗
32. Y. Bai and B. Budd: Adiabatic Shear Localisation, Oxford, UK, Pergamon Press, 1992.
33. Y.B. Xu, W.L. Zhong, Y.J. Chen, L.T. Shen, Q. Liu, Y.L. Bai, M. A. Meyers: Mater. Sci. & Engg. A, 2001, vol. 299, pp. 287-95.10.1016/S0921-5093(00)01412-X ↗
34. M. Zhou, A.J. Rosakis, G. Ravichandran: J. Mech. Phys. Solids., 1996, vol. 44, pp. 981-1006.10.1016/0022-5096(96)00003-8 ↗
35. A. Molinori, C. Musquar, G. Sutter: Int. J. Plasticity, 2002, vol. 18, pp. 443-59.10.1016/S0749-6419(01)00003-1 ↗
36. Y. Yang, B.F. Wang, B. Hu, K. Hu, Z.G. Li: Mater. Sci. Engg. A, 2005, vol. 398, pp. 291-96.10.1016/j.msea.2005.03.099 ↗
37. R.L. Woodward: Int. J. Mech. Sci., 1978, vol. 20, pp. 599-607.10.1016/0020-7403(78)90018-8 ↗
38. B. Venkataraman and G. Sundararajan: Acta.Mater., 1996, vol. 44, pp. 461-73.10.1016/1359-6454(95)00218-9 ↗
39. T. W. Wright: Adiabatic Shear Localisation, 2012, 2nd ed., pp. 215.10.1016/B978-0-08-097781-2.00005-8 ↗
40. A. Marchand and J. Duffy: J. Mech. Phys. Solids., 1988, vol. 36, pp. 251-83.10.1016/0022-5096(88)90012-9 ↗
41. A.M. Merzer: J. Mech. Phys. Solids, 1982, vol. 30, pp. 323-38.10.1016/0022-5096(82)90003-5 ↗
42. C. McVeigh and W.K. Liu: J. Mech. Phys. Solids, 2010, vol. 58, pp. 187-205.10.1016/j.jmps.2009.10.006 ↗
43. D. Rittle, I.G. Wang, A. Dorogoy: Int. J. Impact Engg., 2008, vol. 35, pp. 1280-92.10.1016/j.ijimpeng.2007.07.009 ↗
44. X.W. Chen, Q.M. Li, S.C. Fan: Int. J. Impact Engg., 2005, vol. 31, pp. 877-93.10.1016/j.ijimpeng.2004.04.011 ↗
45. A. Molinari: J. of Applied Mechanics, 1987, vol. 54, pp. 806-12.10.1115/1.3173121 ↗
46. H. Feng, M.N. Bassim: Mat. Sci. Engg. A, 1999, vol. 266, pp. 255-60.10.1016/S0921-5093(99)00026-X ↗
47. M.A. Meyers, G. Subhash, B.K. Kad, L. Prasad: Mech. Materials, 1994, vol. 17, pp. 175-93.10.1016/0167-6636(94)90058-2 ↗
48. G. Sundararajan: Proc. 6th Int. Conf. Fracture, Pergamon Press, London 1986, 5, pp. 3119.
49. 49. Carslaw HS, Jaeger JC (1959) Conduction of heat in solids. Clarendon Press, Oxford
50. Y. Tirupataiah and G. Sundararajan: J. Mech. Phys. of Solids, 1991, vol. 39, pp. 243-71.10.1016/0022-5096(91)90005-9 ↗