Effect of Sintering on the Properties of γ-Brass (Cu5Zn8) Nanoparticles Produced by the Electric Arc Discharge Method and the Thermal Conductivity of γ-Brass Oil-Based Nanofluid
Source abstract
Abstract
Cu5Zn8 nanoparticles with a mean particle size of 21 nm were produced using the electric arc discharge method at 1 atm pressure Ar and 300 A arc current. The effect of sintering on the properties of Cu5Zn8 nanoparticle pellets prepared by pressing nanopowders under 750 MPa pressure was studied. Particles grew uniformly when sintered at 1013 K (740 °C), as opposed to those samples that were unsintered, resulting in a reduction of pores and an increase in density of about 21 pct. The electrical resistivity and hardness of the samples were also highly reduced. The results showed that the cooling rate can affect the properties of the sintered samples. The oil-based nanofluids with 0.2 to 3 wt pct of Cu5Zn8 nanoparticles were prepared, and it was found that the thermal conductivity of nanofluids increased with an increase in the weight percent of nanoparticles up to 1 pct and decreased afterward. The highest increase in thermal conductivity of 6 pct was measured compared to the base fluid.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Lubricants and Their Additives · Electrodeposition and Electroless Coatings · Block Copolymer Self-Assembly
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (21)
Show source-provided references
1. 1. C. Kittel: Introduction to Solid State Physics, John Wiley & Sons Inc., Berkeley, CA, 2005, pp. 625–28.
2. 2. W.F. Smith and J. Hashemi: Foundations of Materials Science and Engineering, McGraw-Hill Inc., New York, NY, 2006.
3. 3. C. Salzemann, F. Kameche, A. Ngo, P. Andreazza, M. Calatayud, and C. Petit: Faraday Disc ., 2015, vol. 181, pp. 19–36.10.1039/C5FD00002E ↗
4. 4. R. Ferro and A. Saccone: Intermetallic Chemistry, Elsevier, Philadelphia, PA, 2008, pp. 728–29.
5. 5. N.K. Mukhopadhyay, D. Mukherjee, and S. Bera: Mater. Sci. Eng. A, 2008, vol. 485, pp. 673–80.10.1016/j.msea.2007.10.039 ↗
6. 6. A.J. Bradley: Physica, 1949, vol. 15, pp. 170–74.10.1016/0031-8914(49)90038-5 ↗
7. 7. N.A. Jasli, H.A. Hamid, and R. Mayappan: Adv. Mater. Res., 2013, vol. 620, pp. 273–77.10.4028/www.scientific.net/AMR.620.273 ↗
8. 8. M.S. Liu, M.C.C. Lin, and C.C. Wang: Nanoscale Res. Lett., 2011, vol. 6, p. 297.10.1186/1556-276X-6-297 ↗
9. 9. E. Ebrahimnia-Bajestan, M. Charjouei Moghadam, H. Niazmand, W. Daungthongsuk, and S. Wongwises: Int. J. Heat Mass Transfer, 2016, vol. 92, pp. 1041–52.10.1016/j.ijheatmasstransfer.2015.08.107 ↗
10. 10. Y.Y. Wu, W.C. Tsui, and T.C. Liu: Wear, 2007, vol. 262, pp. 819–25.10.1016/j.wear.2006.08.021 ↗
11. 11. M. Chopkar, S. Kumar, D.R. Bhandari, P.K. Das, and I. Manna: Mater. Sci. Eng. B, 2007, vol. 139, pp. 141–48.10.1016/j.mseb.2007.01.048 ↗
12. 12. G. Paul, J. Philip, B. Raj, P.K. Das, and I. Manna: Int. J. Heat Mass Transfer, 2011, vol. 54, pp. 3783–88.10.1016/j.ijheatmasstransfer.2011.02.044 ↗
13. 13. M. Farbod and A. Mohammadian: Intermetallics, 2014, vol. 45, pp. 1–4.10.1016/j.intermet.2013.09.012 ↗
14. 14.M. Farbod and M.M. HasaniMatin: Curr. Nanosci., 2011, 7: 794–9610.2174/157341311797483790 ↗
15. 15. M. Farbod and A. Movahed: Mater. Lett., 2012, vol. 89, pp. 140–42.10.1016/j.matlet.2012.08.091 ↗
16. 16.G.F. VanderVoort: Metallography and Microstructures, vol. 9, ASM Handbook, ASM International Inc, Materials Park, OH, 2004, p. 2254.10.31399/asm.hb.v09.9781627081771 ↗
17. 17. G.E. Dieter: Mechanical Metallurgy, McGraw-Hill Inc., New York, NY, 1988.
18. 18. H. Liang, X. Yao, H. Deng, H. Zhang, X. Liu, and Z. Huang: J. Eur. Ceram. Soc., 2015, vol. 35, pp. 399–403.10.1016/j.jeurceramsoc.2014.08.025 ↗
19. 19. A.R. Madaria, A. Kumar, F.N. Ishikawa, and C. Zhou: Nano Res., 2010, vol. 3, pp. 564–73.10.1007/s12274-010-0017-5 ↗
20. 20. X. Yang, Y. Yang, and J. Chen: Tectonophysics, 2014, vols. 619–620, pp. 133–42.10.1016/j.tecto.2013.09.012 ↗
21. 21. H.E. Patel, T. Sundararajan, and S.K. Das: Nanopart. Res., 2010, vol. 12, pp. 1015–31.10.1007/s11051-009-9658-2 ↗