journal article·2014-08

The Effect of Cu Powder During Friction Stir Welding on Microstructure and Mechanical Properties of AA3003-H18

B. Abnar, M. Kazeminezhad, A. H. Kokabi

Publisher page

Abstract

Friction stir welding (FSW) was used to join 3003-H18 non-heat-treatable aluminum alloy plates by adding copper powder. The copper powder was first added to the gap (0.1 and 0.2 mm) between two plates and then the FSW was performed. The specimens were joined at various rotational speeds of 800, 1000, and 1200 rpm at traveling speeds of 70 and 100 mm/min. The effects of rotational speed, second pass of FSW, and direction of second pass also were studied on copper particle distribution and formation of Al-Cu intermetallic compounds in the stir zone. The second pass of FSW was carried out in two ways; in line with the first pass direction (2F) and in the reverse direction of the first pass (FB). The microstructure, mechanical properties, and formation of intermetallic compounds type were investigated. In high copper powder compaction into the gap, large clusters were formed in the stir zone, while fine clusters and sound copper particles distribution were obtained in low powder compaction. The copper particle distribution and amount of Al-Cu intermetallic compounds were increased in the stir zone with increasing the rotational speed and applying the second pass. Al2Cu and AlCu intermetallic phases were formed in the stir zone and consequently the hardness was significantly increased. The copper particles and in situ intermetallic compounds were symmetrically distributed in both advancing and retreating sides of weld zone after FB passes. Thus, the wider area was reinforced by the intermetallic compounds. Also, the tensile test specimens tend to fracture from the coarse copper aggregation at the low rotational speeds. At high rotational speeds, the fracture locations are placed in HAZ and TMAZ.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. R.S. Mishra and Z.Y. Ma: Mater. Sci. Eng., 2005, vol. 50, pp. 1-78.10.1016/j.mser.2005.07.001 ↗
2. R. Nandan, T. DebRoy, and H.K.D.H. Bhadeshia: Prog. Mater. Sci., 2008, vol. 53, pp. 980-1023.10.1016/j.pmatsci.2008.05.001 ↗
3. R.S. Mishra and M.W. Mahoney: Friction Stir Welding and Processing, 1st edition, ASM International, Novelty, OH, 2007, pp. 52-58.
4. H. Aydin, A. Bayram, M.T. Yildrim, and K. Yigit: Mater. Sci., 2010, vol. 16, pp. 311-19.
5. M. Sarkari Khorrami, M. Kazeminezhad, and A.H. Kokabi: Mater. Sci. Eng. A, 2012, vol. 543, pp. 243-48.10.1016/j.msea.2012.02.082 ↗
6. G. Mathers: The Welding of Aluminium and Its Alloys, Woodhead Publishing Ltd, Cambridge, 2002, pp. 41, 161–165.10.1201/9781439823224 ↗
7. P. M. G. P. Moreira, M. A. V. de Figueiredo, and P. M. S. T. de Castro: Theor. Appl. Fract., 2007, vol. 48, pp. 169-77.10.1016/j.tafmec.2007.06.001 ↗
8. P. L. Threadgill, A. J. Leonard, H. R. Shercliff, and P. J. Withers: Int. Mater. Rev., 2009, vol. 54, pp. 49-93.10.1179/174328009X411136 ↗
9. W. Woo, L. Balogh, T. Ungár, H. Choo, and Z. Feng: Mater. Sci. Eng. A, 2008, vol. 498, pp. 308-13.10.1016/j.msea.2008.08.007 ↗
10. M. Sarkari Khorrami, M. Kazeminezhad, and A. H. Kokabi: Mater. Des., 2012, vol. 40, pp. 364-72.10.1016/j.matdes.2012.04.016 ↗
11. V. M. Linton and M. I. Ripley: Acta. Mater. 2008, vol. 56, pp. 4319-27.10.1016/j.actamat.2008.04.059 ↗
12. Y. Bozkurt and S. Duman: Sci. Res. Essays, 2011, vol. 6, pp. 3702-16.10.5897/SRE11.616 ↗
13. R. Kumar, K. Singh, and S. Pandey: Trans. Nonferr. Met. Soc. China, 2012, vol. 22, pp. 288-98.10.1016/S1003-6326(11)61173-4 ↗
14. M. A. Mofid, A. Abdollah-zadeh, and F. Malek Ghaini: Mater. Des., 2012, vol. 36, pp. 161-67.10.1016/j.matdes.2011.11.004 ↗
15. W. F. Xu, J. H. Liu, D. L. Chen, G. H. Luan, and J. S. Yao: Mater. Sci. Eng. A, 2012, vol. 548, pp. 89-98.10.1016/j.msea.2012.03.094 ↗
16. L. Fratini, G. Buffa, and R. Shivpuri: Int. J. Adv. Manuf. Technol., 2009, vol. 43, pp. 664-70.10.1007/s00170-008-1750-8 ↗
17. H. Zhang and H. Liu: Mater. Des., 2013, vol. 45, pp. 206-11.10.1016/j.matdes.2012.09.022 ↗
18. H. J. Zhang, H. J. Liu, and L. Yu: Mater. Des., 2011, vol. 32, pp. 4402-07.10.1016/j.matdes.2011.03.073 ↗
19. H. J. Liu, H. J. Zhang, and L. Yu: Mater. Des., 2011, vol. 32, pp. 1548-53.10.1016/j.matdes.2010.09.032 ↗
20. H. J. Zhang, H. J. Liu, and L. Yu: Trans. Nonferr. Met. Soc. China., 2013, vol. 23, pp. 1114-1122.10.1016/S1003-6326(13)62573-X ↗
21. C. J. Hsu, P. W. Kao, and N. J. Ho: Scripta Mater., 2005, vol. 53, pp. 341-45.10.1016/j.scriptamat.2005.04.006 ↗
22. K. Inada, H. Fujii, Y. S. Ji, Y. F. Sun, and Y. Morisada: Sci. Technol. Weld. Join., 2010, vol. 15, pp. 131-36.10.1179/136217109X12568132624244 ↗
23. H. S. Arora, H. Singh, and B. K. Dhindaw: Int. J. Adv. Manuf. Technol., 2012, vol. 61, pp. 1043-55.10.1007/s00170-011-3758-8 ↗
24. K. Inada, H. Fujii, and Y. S. Ji: Mater. Sci. Forum., 2010, vol. 638–642, pp. 2058-63.10.4028/www.scientific.net/MSF.638-642.2058 ↗
25. L. Ke, C. Huang, L. Xing, and K. Huang: J. Alloys Compd., 2010, vol. 503, pp. 494-99.10.1016/j.jallcom.2010.05.040 ↗
26. J. Gilbert Kaufman: Introduction to Aluminum Alloys and Tempers, 1st edition, ASM International, Novelty, OH, 2000, pp. 111-12.
27. M. M. R. Jaradeh and T. Carlberg: J. Mater. Sci. Technol., 2011, vol. 27(7), pp. 15-627.10.1016/S1005-0302(11)60116-3 ↗
28. H. W. Huang and B. L. Ou: Mater. Des., 2009, vol. 30, pp. 2685-92.10.1016/j.matdes.2008.10.012 ↗
29. G. L. You, N. J. Ho, and P. W. Kao: Mater. Lett., 2013, vol. 90, pp. 26-29.10.1016/j.matlet.2012.09.028 ↗
30. ASTM Standards: ASTM E8-04, Standard Test Methods for Tension Testing of Metallic Materials, ASTM Standards, 2004.
31. ASM International: Powder Metal Technologies and Applications, ASM Handbook, ASM International, 1998, vol. 07, pp. 63–64.
32. F. V. Lenel: Powder Metallurgy: Principles and Applications, Metal Powder Industries Federation, Princeton, 1980, pp. 102-05.
33. R. Beygi, M. Kazeminezhad, and A. H. Kokabi: Trans. Nonferr. Met. Soc. China, 2012, vol. 22, pp. 2925-29.10.1016/S1003-6326(11)61555-0 ↗
34. P. Xue, D. R. Ni, D. Wang, B. L. Xiao, and Z.Y. Ma: Mater. Sci. Eng. A, 2011, vol. 528, pp. 4683-89.10.1016/j.msea.2011.02.067 ↗
35. P. Xue, B.L. Xiao, D. R. Ni, and Z. Y. Ma: Mater. Sci. Eng. A., 2010, vol. 527, pp. 5723-27.10.1016/j.msea.2010.05.061 ↗
36. R. M. Leal, C. Leitao, A. Loureiro, D. M. Rodrigues, and P. Vilaça: Mater. Sci. Eng. A, 2008, vol. 498, pp. 384-91.10.1016/j.msea.2008.08.018 ↗
37. C. Genevois, M. Girard, B. Huneau, X. Sauvage, and G. Racineux: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 2290-95.10.1007/s11661-011-0660-9 ↗
38. M. Azizieh, A. H. Kokabi, and P. Abachi: Mater. Des., vol. 32, pp. 2034-41.10.1016/j.matdes.2010.11.055 ↗