Effects of Au plating on dynamic resistance during small-scale resistance spot welding of thin Ni sheets
Source abstract
Abstract
The effects of Au plating on dynamic resistance during small-scale resistance spot welding of thin Ni sheets have been investigated. Compared to the small-scale resistance spot welding of bare Ni, the Au-plated material showed much lower initial static resistance, and the contribution of constriction resistance to overall dynamic resistance reduced to a negligible value very early in the welding sequence because of the low softening temperature and its lack of surface oxide film. For the same reason, the asperity heating and surface breakdown stages during resistance spot welding of bare Ni were not observed during resistance spot welding of Au-plated Ni. Furthermore, the partial surface melting stage was replaced by the solid-state bonding and brazing stages. Step increases in the sheet-to-sheet dynamic resistance curves of Au-plated Ni were shown to be due to the peripheral unzipping of a prior solid-state bond caused by uneven local thermal expansion. The electrode-to-electrode dynamic resistance curve when welding Au-plated material is not useful for monitoring the state of nugget formation.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Electrical Contact Performance and Analysis · Electronic Packaging and Soldering Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (15)
Show source-provided references
1. Resistance Welding Manual, 5th ed., Resistance Welder Manufacturers’ Association, Philadelphia, PA, 2003, pp. 1–3 to 1–4.
2. D.W. Dickinson, J.E. Franklin, and A. Stanya: Welding Res. Suppl., 1980, vol. 59 (6), pp. 170s-176s.
3. J.G. Kaiser, G.J. Dunn, and T.W. Eagar: Welding Res. Suppl., 1982, vol. 61 (6), pp. 167s-174s.
4. M. Towey and D.R. Andrews: Welding Met. Fabr., 1968, vol. 36 (10), pp. 383–92.
5. B.M. Brown: Welding J., 1987, vol. 66 (1), pp. 18–23.
6. W.F. Hess and R.L. Ringer: Welding Res. Suppl., 1938, vol. 17 (10), pp. 39s-48s.
7. W. Tan, Y. Zhou, and H.W. Kerr: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2667–75.10.1007/s11661-002-0388-7 ↗
8. W. Tan, Y. Zhou, H.W. Kerr, and S. Lawson: J. Phys. D, Appl. Phys., 2004, vol. 37 (14), pp. 1998–2008.10.1088/0022-3727/37/14/017 ↗
9. Electric Contacts Theory and Application, R. Holm, ed., Springer-Verlag, New York, NY, 1967, pp. 9–26.
10. Physical Design of Electronic System, D. Baker et al., eds., Prentice-Hall Inc., Englewood Cliffs, NJ, 1971, vol. 3.
11. B.H. Chang, M.V. Li, and Y. Zhou: Sci. Technol. Welding Joining, 2001, vol. 6 (5), pp. 273–80.10.1179/136217101101538875 ↗
12. ASM Handbook (formerly Metals Handbook, 10th ed.), ASM INTERNATIONAL. Materials Park, OH, 1992, vol. 2, pp. 704–05.
13. Binary Alloy Phase Diagrams, T.B. Massalski, ed., ASM Handbook, ibid., 1992, vol. 3, p. 273.
14. Analytical Chemistry of the Noble Metals, F.E. Beamish, Pergamon Press, Oxford United Kingdom, 1966, pp. 26–38.
15. S.A. Gedeon and T.W. Eagar: Metall. Trans. B, 1986, vol. 17B, pp. 887–901.10.1007/BF02657152 ↗